Fisher Scientific ABR-Z32, ABR-Z33, MP-EP10X-305, MP-ECZ1, MP-HTT2 User Manual

Broad Range Zoom Microscope Head

Binocular and Trinocular Models

User Guide

Broad Range Zoom Microscope Head

Assembly Instructions

Parts Included

1. Optical Head

- ABR-Z32 or

- ABR-Z33

2. Pair of 10x Eyepieces

- MP-EP10X-305

3. Pair of Eyecups

- MP-ECZ1

4. Trinocular Port Adaptor

(trinocular model only)

- MP-HTT2

5. Dust Cover (not shown)

Additional eyepieces and
lenses are available; contact
Customer Service for more
information.

Specications

Working Distance 100mm (3.93”)

Primary Magnication 0.65X to 6.0X

Magnication with

10X eyepieces

Zoom Ratio

Field of View 32.10mm — 3.83mm

Resolution 25µ — 4µ

6.5X to 60X

9.2:1

Setup and Operation

1. Mount head on stand

a. Loosen the head retention screw, place the

head into the ring mount, and secure with
the head retention screw.

b. Remove the protective cover on the

objective housing.

2. Prepare eyepieces

a. Remove the eyetube covers and insert

eyepieces into the eyetubes.

b. Slide the eyecups over the eyepieces.

3. Adjust interpupillary distance

a. Place a specimen on the stage and bring it

into focus.

b. While looking through both eyepieces,

move eyepieces together or apart until the
eld appears as one circle.

4. Adjust diopter (Note: Each user should make this

adjustment before use.)

a. Set a at specimen on the stage plate and

turn the zoom control knobs all the way
toward you to the lowest setting.

b. Use the focus knobs (on stand) to bring the

image into sharp focus.

c. Turn the zoom control to the highest

setting and refocus.

d. Close your left eye and adjust the diopter

on the right eyetube until the image is
clear; then close your right eye and repeat
the process.

e. When each eyetubes focuses sharply, the

diopter is properly set.

5. Adjust magnication

a. First, focus on a specimen at the highest

magnication setting (turn zoom control
knobs all the way back) to ensure the
specimen stays in focus at all magnications.

b. Turn the zoom control knobs toward you

to lower the magnication.

Magnication = eyepiece value × zoom value

Westover Scientic Customer Service

Toll Free Customer &
Technical Service 866-614-4022

Local and International
Customer & Technical Service 425-368-0444
Fax [phone]

Customer service hours are 7:00 a.m. to 4:00 p.m. Pacic Standard Time.

Eyecups

Eyepieces

Diopter Adjustment

Trinocular
Port

Trinocular Model

1. Change the light path direction

a. Slide the prism bar (left side of head,

not shown) all the way in to direct the
light to the binocular eyepieces.

b. Slide the prism bar out to directed

light to the trinocular port. Note that
you cannot simultaneously observe
the sample with both the eyepieces
and the trinocular port.

2. Attach a camera to the trinocular port

a. Use a compatible camera and camera

adaptor.
Trinocular port ID = 27mm
Trinocular port adapter ID = 23mm

b. Refer to the manufacturer’s

instructions to install the camera and
camera adapter.

3. Adjust the camera adaptor so that it

is parfocal (the image in focus in the
eyepieces is also in focus in the camera.)

a. Focus on a sample while looking through

the eyepieces at the highest magnication,
and then slide out the prism.

b. Loosen the set screw on the trinocular

port and slide the tube up or down
to adjust the adapter height until the
image on the camera is in focus. Do
not use the focusing knobs to focus
the camera image.

c. Tighten the set screw to secure the

adapter.

Set Screw for

adaptor
adjustment

Zoom Control
Knob

Objective Housing

Statement of Limited P roduct Warrant y: These models are warranted to be free of all defects in material and workmanship for a period of 12 months (1 year) from the date of delivery. The warranty does not apply to any instrument
which has become worn, defective, damaged or broken due to abuse, misuse, tampering, or unauthorized repairs. Under this warranty, Westover Scientic will repair or replace, without charge to the purchaser, any part which upon our examination,
appears to be defective in materials or workmanship. Returned Goods Policy for Repair or Replacement Parts: To return goods for repair or replacement, please contact Westover Scientic Customer Service.

diScLai mer: Information provided by Westover Scientic is believed to be accurate and reliable. However, no responsibility is assumed by Westover Scientic for its use. The information contained in this publication is subject to change without
notice. Words that Westover Scientic considers trademarks have been identied as such. However, neither the presence nor absence of such identication aects the legal status of any trademark. Units of measurement in this document conform
to SI standards and practices. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form, be it electronically, mechanically, or by any other means such as photocopying, recording, or
otherwise, without the prior written permission of Westover Scientic Inc.

Manufactured by WESTOVER SCIENTIFIC, INC. | 18421 Bothell-Everett Hwy, Suite 150 | Mill Creek, WA 98012

© 2009 Westover Scientic, Inc. All rights reserved. ZP-PKGA-0208 REV 01