Page 1
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Requires three “AA” batteries for operation (included).
Tool required for assembly: Phillips screwdriver (not included).
www.fisher-price.com
Page 2
Head
Assembled Parts
Track 2
Track 1
Base
Part not shown: label sheet.
1
#6 x 1
#6 x
/
3
/
" - 16
4
” - 1
2
Post
(2 Pieces)
4 Feet
Screws Shown Actual Size
Note: Tighten and loosen all screws
with a Phillips screwdriver.
Do not over-tighten.
2
Page 3
Assembly
CAUTION
This product contains small parts in its unassembled
state, Adult assembly is required. Take extra
care during unpacking and assembly.
Foot
Base
PUSH
1
• Place the base upside down on a flat surface.
• Fit a foot into the grooved areas in the base.
• Insert four #6 x
• Repeat this assembly process to assemble the other
three feet.
• Turn the toy upright.
Post
3
/
” screws into the foot and tighten.
4
Post
3
• Insert and “snap” the post into the slots in the top of the base.
Hint: The post is designed to fit into the base one way!
Post
Track 1
Ta b
Base Slot
4
2
• Fit both halves of the post together. Squeeze them to “snap”
into place.
• Position track 1 with the grooved side up.
• Fit track 1 onto the post. Turn it clockwise until it reaches
the base.
• Insert and “snap” the tab on the end of track 1 into the slot
in the base.
3
Page 4
Track 2
Slot
Small Tab
5
Small TabSmall Tab
Track 1
Assembly
SlotSlot
Head
• Position track 2 with the grooved side up. Slide track 2 onto
the post.
• Turn track 2 clockwise until it meets track 1. Insert and “snap”
the tab on the end of track 2 into the slot in track 1. Be sure
the small tab on the end of track 2 fits into the slot in track 1.
#6 x 1 1/2”
Screw
Track 2
6
7
• Fit the head onto the post, as shown.
• Press down on the head to “snap” it into place. Pull up on the
head to be sure it is secure.
1
2
1
3
2
3
8
1
• Insert the #6 x 1
into the post. Tighten the screw.
/
” screw through the hole in track 2 and
2
• Make sure the areas where the labels will be applied are
clean and dry. Wipe this product with a clean, soft, dry cloth
to remove any dust or oils.
• For best results, do not attempt to apply a label more
than once.
• Apply the labels as shown in the illustrations above.
4
Page 5
Battery Replacement
Lights and Sounds Fun!
1,5V x 3
“AA” (LR6)
For best performance, we recommend replacing the
batteries that came with this toy with three, new alkaline
“AA” (LR6) batteries.
• Locate the battery compartment on the back of the
giraffe’s head.
• Loosen the screws in the battery compartment door and
remove the door. Remove the exhausted batteries and
throw them away.
• Insert three, new “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically, you may need
to reset the electronics. Slide the power/volume switch off
and then back on.
• When sounds or lights from this toy become faint or stop,
it’s time for an adult to change the batteries!
Press
Power/Volume Switch
Press for music
and lights!
• Slide the power/volume switch on the back of the head to
ON with high volume ; ON with low volume or OFF .
• Place a ball in the giraffe’s mouth for fun sounds and music.
Watch the ball spiral down!
• Press the button on the head for music and lights.
• Protect the environment by not disposing of this
product with household waste (2002/96/EC).
Check your local authority for recycling advice and
facilities (Europe only).
5
Page 6
Consumer Information
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product.
Dispose of batteries safely. Do not dispose of this product in
a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
•
Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are only
to be charged under adult supervision.
FCC Statement (United States Only)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
ICES-003
This Class B digital apparatus complies with Canadian
ICES-003. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada. L’utilisation de ce dispositif est
autorisée seulement aux conditions suivantes: (1) il ne doit pas
produire de brouillage et (2) l’utilisateur du dispositif doit être
prêt à accepter tout brouillage radioélectrique reçu, meme si
ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Care
• Wipe this toy with a clean cloth dampened with a mild soap
and water solution. Do not immerse this toy.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2010 Mattel, Inc. All Right Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
K8844b-0920
PRINTED IN CHINA
Loading...