Page 1
V7599
Please keep this instruction
sheet for future reference, as it
contains important information.
Adult assembly is required.
No tools needed for assembly.
www.fisher-price.com
Page 2
IMPORTANT!
• Your toy includes bubble solution in
the bubble dispenser. Once bubble
solution is gone, do not remove or
throw away the bubble dispenser
that comes with this toy. Simply
refill the bubble dispenser with
bubble solution.
• Use only bubble solution in this toy.
• Make sure your child understands
that bubble solution is not for drinking
and that it should be kept away from
the eyes.
• While filling or cleaning this toy, try
to avoid spilling bubble solution on
the floor. It may create slippery
floor conditions.
• Bubble solution used in this product
may stain or stick to some surfaces.
Water toys sometimes get messy. •
Protect play surfaces before use.
To avoid bubble solution leaking •
from this toy, do not over-fill the
bubble chamber.
Assembly
Lower Handle
1
1
• Insert and "snap" the lower handle
into the socket in Mater, as shown.
Handlebar
2
1
• Fit the handlebar into the socket on
one side of the lower handle.
•
Push to "snap" the handlebar in place.
2
Page 3
Using the Bubble Dispenser
IMPORTANT! Before use, remove
the cap and seal from the bubble
dispenser and throw it away.
Engine Cover
Cap
2
1
Bubble
Dispenser
1
1
Slide the engine cover to access the •
bubble dispenser.
Locate the cap in the engine.•
Attach the cap to the top of the •
bubble dispenser. Twist the dispenser
to secure it to the cap.
• Turn the bubble dispenser over so that
the cap is down and insert it back into
the engine.
3
1
• Replace the engine cover over the
bubble dispenser and press down
for about 15 seconds to fill the
bubble chamber inside Mater.
3
Page 4
Bubblin' Fun
• Make sure all four wheels contact
the ground when pushing this toy.
• Bubbles will begin to blow after
about 15-20 walking steps and keep
blowing as long as the toy is
being pushed!
• When bubbles stop, press the bubble
Note: We do not recommend the use
of silicones or oily lubricants on this
toy. As with any bubble producing toy,
when even a very small amount of
silicone or oily lubricants are put into
or used near the bubble chambers,
bubbles will not form.
dispenser again for 15 seconds to
refill the fun!
©Disney/Pixar
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2011 Mattel, Inc.
All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc., unless otherwise indicated.
PRINTED IN MEXICO V7599pr-0920
4
Page 5
Let's Clean Up
1
1
• Slide the engine cover to the side and
lift to remove the bubble dispenser
from the engine.
• Turn the bubble dispenser upright and
twist to
2
• Thoroughly rinse the bubble chamber
on the side of this toy and the opening
in the engine with clean water from a
garden hose or faucet.
remove
1
the cap.
Rinse HereRinse Here
3
1
• Tip this toy forward to empty all the
water.
Cap End Up
For Storage
4
1
• Replace the cap on the bubble
dispenser and place the it back into
the engine, cap end up.
IMPORTANT! Do not remove or throw
away the bubble dispenser that comes
with this toy. Simply refill the bubble
dispenser with bubble solution.
5
Page 6
CONSU
CE
Problems and Solutions
Problem Cause Solution
No bubbles Not enough bubble solution in
bubble chamber
Bubble chamber is clogged
and dirty
You have not walked far enough
to produce bubbles
You are walking too quickly Walk at a slow, steady pace.
The rear wheels do not contact
the ground
Silicone or oily lubricants
got into the bubble chamber
Bubble solution is leaking Bubble chamber over-filled Fill only by using the attached
This toy is being pushed uphill Use only on flat, level ground.
Bubble solution is foaming Bubble chamber is clogged Follow instructions in "Let's
Press down on bubble dispenser
for 15 seconds to refill.
Follow instructions in “Let’s
Clean Up” section to clean bubble
chamber thoroughly.
This toy needs to be pushed a
minimum of 15-20 walking steps
before bubbles will begin to blow.
Push this toy so that the
rear wheels always contact
the ground.
Never use silicone or oily
lubricants on this product (the
wheels). Bubbles will not form
if even a very small amount of
these substances get into the
bubble chamber.
bubble dispenser.
Clean Up" section to clean bubble
chamber thoroughly.
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
6
MER ASSISTAN
Loading...