Assembly
Fork Post
Label DecorationLabel Decoration
• Periodically, check the plastic parts and if broken or
• Periodically, check all fasteners regularly to be sure they
• To clean, use a mild soap and water solution and a clean
Consumer Information
cracked, dispose of them properly.
are tight. If the fasteners are not tight, tighten them
as necessary.
cloth. Rinse clean with water to remove soap residue.
V4270
9
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
Handlebar Front
Handlebar Back
¾" Screw
2¼" Screw
Fork Cover
Fork Post
¾" Screw
7
BACK VIEW
2
FRONT VIEW
• Wipe the trike with a clean, dry cloth to remove any dust
or oils before applying labels.
• Apply labels exactly as shown in the illustrations. For best
results, avoid repositioning the label after it has been applied.
• Starting at the center of a label rub rmly with a dry cloth,
and smooth towards the outer edges to remove air bubbles.
8
RIGHT SIDE VIEW
LEFT SIDE VIEW
IMPORTANT! It is a good practice to start training children
very young regarding the importance of helmet use. When
children are older and riding bicycles and faster vehicles,
it is important that they use a helmet each and every time
they ride. For this reason, even while riding a tricycle, it is
a good idea to familiarize your child with helmet use,
so that it becomes a habit for life. Choose a helmet that
complies with requirements of the applicable certifying
agency for bicycle helmets.
UMER
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
10
• Fit the handlebar front to the fork post.
Hint: The handlebar front is designed to assemble to the
fork post one way.
• Fit the handlebar back to the fork post and handlebar
front. Hold them together rmly.
• First, insert the remaining #8 x ¾" screws through the
outer holes in the handlebar back and tighten.
• Then, insert the #8 x 2¼" screw through the center hole
in the handlebar back and tighten.
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tools required for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (not included).
Nick.com
©2010 Viacom International Inc. All Rights Reserved. Nickelodeon, Nick Jr., Go, Diego, Go! and all related titles, logos and characters are trademarks of Viacom International, Inc.
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc., unless otherwise indicated.
5
PRINTED IN MEXICO V4270pr-0920
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
Weight limit: 55 lbs (25 kg).
www.fi sher-price.com
Age: 2-5 years
Consumer Information
Assembly
Assembly
WARNING CAUTION
TO AVOID SERIOUS INJURY:
• Adult supervision is required.
•
Never use near cars and other motor
vehicles, near streets, steps, sloped
driveways, hills, roadways, alleys, swimming
pools or other bodies of water.
• Always wear shoes.
• Never allow more than one rider.
*We’ve included one extra .354" cap nut for your convenience.
#8 x 2¼" Screw - 1
#8 x¾" Screw - 6
FASTENERS SHOWN ACTUAL SIZE
Parts
• Please save all packaging material until assembly is complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry cloth before assembly.
• Some parts shown are assembled to both sides of the trike.
• Tighten assembled screws with a Phillips screwdriver. Do not over-tighten the screws.
• Part not shown: Label Sheet.
Handlebar Front
Handlebar Back
.354"
.354" Cap Nut - 2*
This product contains small parts
in its unassembled state.
Adult assembly is required.
PUSH
Seat
Frame
1
• Fit the seat onto the frame. Push rmly near the back end
of the seat to "snap" it into place.
Bushing
(Grooved Side Down)
Straight Axle Assembly
3
• Turn the frame upside down.
• Insert the straight axle assembly through the holes in the
rear of the frame.
Straight Axle
BOTTOM VIEW
Rear Wheel
(Flat Side First)
.354"
5
• Fit the cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel to be sure the cap nut is securely attached to
the straight axle.
Hint: You may need the help of another adult to hold the
other end of the straight axle in place.
Pedal Axle Tab
Pedal Hub
Pedal Hub
7
• Fit two pedal hubs onto the pedal axle tabs. Make sure
the tabs t into the slot in each pedal hub.
• Press the pedal hubs into the center of the front wheel
until they are ush with the surface of the front wheel.
• Repeat this procedure to assemble the remaining
pedal hubs.
Fork Arms
Front Wheel
Assembly
Seat
Straight Axle
2 Bushings
Frame
Fork
2 Fork Covers
4 Pedal Hubs
Front Wheel Assembly
Rear
Wheel
(Indented
Side Down)
Wheel Hub
(Flat Side Down)
Straight
Axle
.354"
Straight
Axle
Cap Nut
4
• Turn the assembly upright.
• Slide a bushing, smooth side rst, onto the end of the
straight axle.
• Slide a rear wheel, at side rst, onto the end of the
straight axle.
• Slide a wheel hub, pointed end rst, onto the end of the
straight axle.
Bushing
(Smooth Side First)
Wheel Hub
(Pointed End First)
Wheel Hub
2
• Place one end of the straight axle into the cap nut. Tap
the end of the straight axle with a hammer. Make sure
the cap nut is securely attached to the straight axle.
2 Rear Wheels
2 3 4
2 Wheel Hubs 2 Wheel Caps
• Slide a wheel hub, at side down, onto the straight axle.
• Slide a rear wheel, indented side down, onto the
straight axle.
• Slide a bushing, grooved side down, onto the straight axle.
6
• Fit the tabs on the wheel cap into the slots in the wheel
hub. Push to "snap" the wheel cap in place.
• Repeat this procedure to attach the other wheel cap to
the other wheel hub.
Wheel Cap
Groove
Fork Cover
Pedal Axle
8
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle ts into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x ¾" screws into the fork cover and tighten.
• Repeat this procedure to attach the other fork cover to the
other fork arm.