Fisher-Price T6197 User Manual
T6197
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required. Tools required for assembly:
Phillips Screwdriver, Hammer and Scrap Block of Wood (not included).
Requires three "AA" batteries (included).
Age: 2-6 years.
Weight limit: 60 lbs (27 kg).
www.fi sher-price.com
Consumer Information
WARNING CAUTION
To avoid serious injury:
• Adult supervision is required.
• Never use near cars and other motor vehicles,
near streets, steps, sloped driveways, hills,
roadways, alleys, swimming pool areas or
other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
Note: Some parts are assembled on both
sides of the vehicle.
Basket Mount
Handlebar
This product contains small parts
in its unassembled state.
Adult assembly is required.
IMPORTANT!
• Please save all packaging material until assembly is complete
to ensure that no parts are discarded.
• Please wipe each part with a clean, dry cloth before assembly.
• Some parts shown are assembled to both sides of the trike.
Note: Tighten and loosen screws with a Phillips
screwdriver. Do not over-tighten the screws.
#8 x 3/4" Screw – 6
Cap Nut – 1
FASTENERS SHOW ACTUAL SIZE
#6 x 1/2" Screw – 4
#8 x 3" Screw – 1
Basket
Front Wheel
Fork
Frame
Pedal Axle
Cap
2 Fork Covers
Pedal
Straight Axle
2 Rear Wheels
Seat
Seat Retainer
2 Hubcaps
2 Covers
4 Pedal Hubs
Part Not Shown: Label Sheet
©2010
Viacom International Inc. All Rights Reserved. Nickelodeon, Nick Jr., Dora the Explorer
and all related titles, logos and characters are trademarks of Viacom International, Inc.
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc., unless otherwise indicated.
PRINTED IN MEXICO T6197pr-0920
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
2
Assembly
Rear Wheel
(Indented Side Up)
Cap Nut
Hubcap
(Peg Side Down)
Rear Wheel
(Indented Side Down)
Hubcap
(Peg Side Up)
Straight Axle
1
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
Frame
Cover
Hubcap
3
Straight Axle
Frame
Assembled
Rear Wheel
Scrap Block
of Wood
Cap Nut
Assembly Tool
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle. Tap the
cap nut with a hammer. Gently pull the rear wheel up
to be sure the cap nut is securely attached to the
straight axle.
• Insert one of the tabs on a cover into a slot in the hubcap.
Push to snap the cover into place. Repeat this procedure
to attach the other cover to the other hubcap.
Hole
Straight Axle
2
BOTTOM VIEW
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
Hole
Pedal Hub
Pedal Axle
Slot
Ta b
Ta b
Pedal Hub
4
• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs t into the slot in each pedal hub.
3
Loading...