Fisher-Price T4201 User Manual

T4201

Infant Rocker Seat ­Recline Position

Toddler Rocker ­Upright Position

IMPORTANT!

KEEP FOR FUTURE

REFERENCE.

www.fi sher-price.co.uk

Consumer Information

WARNING

To prevent serious injury or death:

• Fall Hazard - Never use this product on an

elevated surface, since child’s movement may
cause the product to slide or tip over. Use
only on a floor.

• Suffocation Hazard - Never use on a soft

surface (bed, sofa, cushion) since the
product can tip over and cause suffocation in
soft surfaces.

• Never leave child unattended.

Care

• The pad is machine washable. Wash the pad separately in
cold water on the gentle cycle. Do not use bleach. Tumble dry
separately on low heat and remove promptly.

• The frame, toy bar and toys may be wiped clean using a mild
cleaning solution and a damp cloth. Do not use bleach. Do not
use harsh or abrasive cleaners. Rinse clean with water to remove
residue. Do not immerse the frame, toy bar and toys.

To remove the pad:

• Unfasten the waist belts. Pull them down through the slots in the
seat pad.

• Unbuckle the straps on the front edge of the pad.

To replace the pad, refer to Assembly steps 8-10.

• Never use as a carrier or lift while child
is seated.

• This product is not intended to replace a cot
or bed for prolonged periods of sleep.

• Use the upright position (toddler mode) only
when child has developed enough upper
body control to sit without leaning forward.

• Always use the restraint system until
child is able to climb in and out of the
product unassisted.

• Do not use reclined position (infant mode)
once child can sit unaided.

• Never use toy bar as a handle.

• Please read these instructions before assembly and use of
this product.

• Adult assembly is required. Tool needed for assembly: Phillips
screwdriver (not included).

• Requires one "D" (LR20) alkaline battery (not included) for
soother operation.

• Product features and decorations may vary from photographs.

• Use the recline position (infant mode) until child is able to sit
unaided (approximately 9 kg/20 lbs).

• This product does not replace a cot or bed. Should the child
need to sleep, place the child in a suitable cot or bed.

• Use the upright position (toddler mode) only when child has
developed enough upper body control to sit without leaning
forward (maximum 18 kg/40lbs).

Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.

Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked
Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.

New Zealand: 16-18 William Pickering Drive, Albany 1331,
Auckland.

Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.

Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].

Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.

PRINTED IN CHINA

Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.

©2010 Mattel, Inc. All Rights Reserved.

®

and ™ designate U.S. trademarks of Mattel, Inc.

2

T4201pr-0726

Parts

IMPORTANT! Please remove all parts from the package and

identify them before assembly. Some parts may be packed
in the pad.

Assembly

CAUTION

This package contains small parts

in its unassembled state.

Adult assembly is required.

IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.

Pad

2 Retainers with Lock Nut

Back Crossbar

2 Side Rails

Seat Back Tube

PRESS

Seat Back Tube

PRESS

Toy Bar

Side Rails

1

Front Crossbar

Note: Tighten or loosen all screws with a Phillips screwdriver.

Do not over-tighten the screws.

M5 x 30 mm Screw – 6

Kickstand

Shown Actual Size

• Fit the ends of the seat back tube to the ends of each side rail.

Hint: The seat back tube is designed to fi t one way. If it does not
seem to fi t, turn it around and try again.

• While pressing the button on the end of the seat back tube/side

rail, continue to insert until the buttons “click” into place.
Make sure you hear a “click” on each side.

• Pull the seat back tube to be sure it is secure on the side rails.

3