Fisher-Price T3643 User Manual

Infant Seat

T3643

Infant Swing

High Chair

www.fi sher-price.com

Toddler Seat

Consumer Information

Infant Seat

• Age: approximately 0-6 months.

• Maximum weight: 25 lbs (11,3 kg).

• Use infant seat from birth until child is able to sit up unassisted.

WARNING

To prevent serious injury or death:

• Fall Hazard

- Never use on any elevated surface, since child's movement may cause infant seat

to slide or tip over. Use only on a oor.

- Never release seat from base with child in seat.

• Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion), since infant

seat may tip over and cause suffocation in soft surfaces.

• Always use restraint system.

• Never leave child unattended.

• The infant seat is not intended to replace a crib or bassinet for prolonged periods
of sleep.

• Never use infant seat for a child able to sit up unassisted.

• Never attach infant seat to a chair.

• Never use as a carrier or lift while child is seated.

Infant Swing

• Age: approximately 0-6 months.

• Maximum weight: 25 lbs (11,3 kg).

• Use infant swing from birth until child becomes active and attempts to climb out of the product.

WARNING

To prevent injury or death from falls and being strangled in the restraint system:

• Always use restraint system.

• Never use with an active child who may be able to climb out of swing.

• Never leave child unattended.

• Never release seat from frame with child in swing. Never carry child in seat.

2

Consumer Information

High Chair

• Age: approximately 6-24 months.

• Maximum weight: 50 lbs (22,6 kg).

• Use high chair only with a child who has enough upper body control to sit up unassisted.

WARNING

To prevent serious injury or death from falls or sliding out:

• Always secure child with restraint belts adjusted to t your child snugly. The tray is
not designed to hold child in high chair.

• Use only with a child who has enough upper body control to sit unassisted.

• Never leave child unattended.

• Never release seat from base with child in high chair. Never carry child in seat.

Toddler Seat

• Age: approximately 18 months and up.

• Maximum weight: 50 lbs (22,6 kg).

• Use toddler seat only with a child capable of getting into and out of the product unassisted.

WARNING

To prevent serious injury or death:

• Fall Hazard

- Never use on any elevated surface, since child’s movement may cause the product
to slide or tip over. Use only on a oor.

- Never release seat from base with child in seat.

• Use only with a child who is able to get in and out of the seat unassisted. Do not use
restraint system.

• Never use as a carrier or lift while child is seated.

• Never attach toddler seat to a chair.

3

Consumer Information

• IMPORTANT! Please keep these instructions for future reference.

• Please read these instructions before assembly and use of
this product.

• Adult assembly is required. Tool required for assembly: Phillips
screwdriver (not included).

• Requires four “C” (LR14) alkaline batteries for swing operation
(not included).

• Product features and decoration may vary from photos.

Care

• Before use, thoroughly wash all parts (the tray) that may contact

food. The tray is not microwave or dishwasher safe.

• The bases, swing frame, legs, seat, toy and tray can be wiped clean

using a mild cleaning solution and a damp cloth. Do not immerse
the swing frame. Do not use bleach. Do not use harsh or abrasive
cleaners. Rinse clean with water to remove residue.

• The pad can be machine washed in cold water on the gentle cycle.

Do not use bleach. Tumble dry on low heat.

To remove the pad:

• Remove the four elastic loops from the pegs on the underside and

back of the seat.

• Push the waist and crotch restraints down through the slots in

the pad.

• Lift to remove the pad from the seat.

• Refer to the Seat Pad Assembly section to replace the pad.

FCC Statement (United States Only)

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manu-

facturer responsible for compliance could void the user’s authority to
operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.

ICES-003

This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause
undesired operation.

NMB-003

Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.L’utilisation de ce dispositif est autorisée seule­ment aux conditions suivantes : (1) il ne doit pas produire de brouillage
et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.

4

Parts

IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad.

Infant Seat Front Crossbar

Toddler Seat Front Crossbar

Swing Frame

Seat

Infant Seat Rear Crossbar

Toddler Seat Rear

Crossbar

2 Swing Arms

(Left and Right)

2 Infant Seat Side Rails

(Left and Right)

2 Toddler Seat Side Rails

(Left and Right)

4 Legs

Toy

High Chair Tray

Pad

Swing Seat Base

Note: The swing seat base is attached

to the seat to fit in the package. Please
remove the seat from the swing seat
base (see page 6).

5

Note: Tighten or loosen all screws with a Phillips

screwdriver. Do not over-tighten the screws.

#8 x 1" (2,5 cm) Screw – 20

Shown Actual Size

CAUTION

Assembly

Seat

This package contains small parts
in its unassembled state. For adult
assembly only.

IMPORTANT! Before assembly and each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges. DO
NOT use if any parts are missing or broken. Contact Fisher-Price® for
replacement parts and instructions if needed. Never substitute parts.

PRESS

Swing Seat

Base

PRESS

1

• Press the buttons on each side of the seat and lift to remove the
seat from the swing seat base.

• Set both parts aside for Infant Swing Frame and Pad assembly.

T-strap

Slot

2

• If desired, fit the toy T-strap down through the slot in the seat.

6

Infant Seat

Front Crossbar

Release Button

Infant Seat Base

One-Time Assembly

Infant Seat

Side Rails

Infant Seat

Rear Crossbar

Release Button

3

1

• Locate the infant seat side rails and the infant seat front crossbar.

• Position the infant seat side rails, as shown, with the release
buttons outward.

• Fit the crossbar into the sockets in the side rails, as shown.

Hint: The crossbar is designed to fit the side rails one way.
If it does not seem to fit, turn it around and try again.

2 Screws

• Fit the infant seat rear crossbar into the sockets in on the side rails,
as shown.

Hint: The crossbar is designed to fit the side rails one way. If it does
not seem to fit, turn it around and try again.

2 Screws

2

• Insert two screws into the holes in the crossbar and tighten.

4

• Insert two screws into the holes in the crossbar and tighten.

• Turn the infant seat base assembly upright.

7

Swing Seat Base

Infant Swing Frame

One-Time Assembly

Swing Frame Hubs

1

• Slide the longer, straight ends of the swing arms through the
holes in the swing seat base.

Hint: The swing arms are designed to fit one way. If a swing arm
does not seem to fit, try inserting it into the other hole in the
swing seat base.

• Turn the assembly over.

2 Screws

Swing Arms

2 Screws

3

• Fit the swing arms into the sockets in the swing frame hubs.

• Turn the assembly around.

4

BACK VIEW

2 Screws

2 Screws

FRONT VIEW

2

• Insert two screws into each swing arm and tighten.

• Turn the assembly upright.

BOTTOM VIEW

• Insert two screws into each hub and tighten.

8

Toddler Seat Base

One-Time Assembly

Curve

Toddler Seat

Front Crossbar

1

Release Button

• Position the toddler seat side rails, with the release buttons outward.

• Position the toddler seat front crossbar with the curve outward.

• Fit posts on the crossbar into the sockets in side rails.

Hint: The crossbar is designed to fit one way. If it does not seem to fit
in the side rails, turn it around and try again.

Toddler Seat

Side Rails

Release Button

Toddler Seat

Rear Crossbar

3

• Fit posts on the toddler seat rear crossbar into the sockets in
side rails.

Hint: The crossbar is designed to fit one way. If it does not seem to
fit onto the side rails, turn it around and try again.

4 Screws

2

• Insert four screws into the crossbar and tighten.

2 Screws

2 Screws

4

• Insert four screws into the crossbar. Fully tighten the screws.

• Turn the toddler seat base upright.

9

Seat Pad Assembly

1

Pad

SIDE VIEW

Seat

Tabs

BOTTOM VIEW

Elastic LoopElastic Loop

Hole

Hole

3

• Fit the pocket on the top of the pad over the seat back.

Slots

Waist Belt

• Insert both elastic loops on the pad through the holes in the
seat bottom.

• From the bottom of the seat, hook the elastic loops to the tabs
on the seat.

Tabs

BOTTOM FRONT VIEW

Waist Belt

Crotch Belt

2

• Lift the front edge of the pad up and fit the waist and crotch belts
up through the slots in the pad.

FRONT VIEW

TOP VIEW

4

• Hook the elastic loops on the front edge of the pad to the tabs
on the seat bottom.

Elastic Loops

10

1,5V x 4

“C” (LR14)

Swing Frame Battery Installation

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:

• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.

• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the product before charging.

• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.

• Locate the battery compartment door on the swing frame.

• Loosen the screws in the battery compartment door with a
Phillips screwdriver.

• Insert four “C” (LR14) alkaline batteries.

Hint: We recommend using alkaline batteries for longer battery life.

• Replace the battery compartment door and tighten the screws. Do
not over-tighten.

• If this product begins to operate erratically, you may need to reset
the electronics. Turn the power off and then back on.

• When motion from the swing becomes slow/faint or stops, it's
time to replace the batteries.

• Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).

11

Use one seat 4 different ways!

Infant Seat

Infant Swing

High Chair

Toddler Seat

12

Infant Seat Use

WARNING

To prevent serious injury or death:

• Fall Hazard

- Never use on any elevated surface,
since child's movement may cause
infant seat to slide or tip over. Use
only on a oor.

- Never release seat from base with
child in seat.

• Suffocation Hazard - Never use on a

soft surface (bed, sofa, cushion), since
infant seat may tip over and cause
suffocation in soft surfaces.

• Always use restraint system.

• Never leave child unattended.

• The infant seat is not intended to

replace a crib or bassinet for prolonged
periods of sleep.

• Never use infant seat for a child able

to sit up unassisted.

• Never attach infant seat to a chair.

• Never use as a carrier or lift while child

is seated.

Seat

Infant Seat Base

Hint: If you are converting to an infant seat from high chair, toddler
seat or swing modes, remove the seat from the toddler seat base
or swing seat base.

• Fit the seat onto the infant seat base.

• Push to “snap” the seat onto the base. Pull up on the seat to

be sure it is secure.

13

WARNING

Infant Swing Use

To prevent injury or death from
falls and being strangled in the
restraint system:

• Always use restraint system.

• Never use with an active child who
may be able to climb out of swing.

• Never leave child unattended.

• Never release seat from frame with
child in swing. Never carry child in seat.

PRESS

PRESS

1

Hint: If you are converting to an infant swing from infant seat mode,
follow this step.

• Press the release buttons on each side of the seat.

• Lift the seat off the infant seat base.

• Set the infant seat base aside for future use.

Swing Frame

Legs

Legs

2

Hint: If you are converting to an infant swing from high chair mode,
remove the legs from the toddler seat base.

• Fit the legs into the holes in the bottom of the swing frame,
as shown.

• Push to “snap” each leg in place. Pull on each leg to be sure it

is secure.

14

Infant Swing Use

Seat

Swing Seat Base

3

Hint: If you are converting to an infant swing from high chair or
toddler seat modes, remove the seat from the toddler seat base.

• Fit the seat onto the swing seat base.

• Push to “snap” the seat in place. Pull up on the seat to be sure

it is secure.

Speed/Power

Switch

4

• Slide the swing speed/power switch ON

• Give the seat a light push to start the swinging motion.

• Adjust the swing speed/power switch to the desired swing
motion setting.

Hints:

- After turning on power, this product may not swing unless there is
a child in the seat.

- As with most battery-power swings, a heavier child will reduce
the amount of swinging motion on all settings. In most cases, the
low setting works best for a smaller child while the higher setting
works best for a heavier child.

- If swinging stops while using a lower setting, try a higher setting.
Give the seat a light push to start the swinging motion again.

• Slide the swing speed/power switch OFF when you are finished.

.

•

15

WARNING

High Chair Use

To prevent serious injury or death
from falls or sliding out:

• Always secure child with restraint
belts adjusted to  t your child snugly.
The tray is not designed to hold child
in high chair.

• Use only with a child who has enough
upper body control to sit unassisted.

• Never leave child unattended.

• Never release seat from base with
child in high chair. Never carry child
in seat.

PRESS

PRESS

PRESS

PRESS

2

• Press the release buttons on the swing frame assembly and pull to
remove the legs.

PRESS

PRESS

1

Hint: If you are converting to a high chair from swing mode, follow
steps 1 and 2.

• Press the release buttons on each side of the seat.

• Lift the seat off the swing seat base.

Toddler Seat Base

3

• Insert each of the legs into the holes in the toddler seat base.

• Push to “snap” each leg in place. Pull on each leg to be sure it

is secure.

Legs Legs

16

Seat

High Chair Base

High Chair Use

6

4

Hint: If you are converting to a high chair from infant seat mode,
remove the seat from the infant seat base.

• Fit the seat onto the high chair base.

• Push to “snap” the seat in place. Pull up on the seat to be sure

it is secure.

Tray

• While pulling the release handles on the sides of the tray, adjust
the tray forward or backward.

7

5

Using the Tray

• Fit the tray onto the seat armrests. Push down until the tray

"snaps" into place.

Hint: Before use, thoroughly wash all parts (the tray) that may
contact food. The tray is not dishwasher or microwave safe.

• While pulling the release handles on the sides of the tray, pull the
tray towards you and lift to remove it from the seat.

17

WARNING

Toddler Seat Use

To prevent serious injury or death:

• Fall Hazard

- Never use on any elevated surface,
since child’s movement may cause
the product to slide or tip over. Use
only on a oor.

- Never release seat from base with
child in seat.

• Use only with a child who is able to get

in and out of the seat unassisted. Do
not use restraint system.

• Never use as a carrier or lift while child

is seated.

• Never attach toddler seat to a chair.

PRESS

PRESS

PRESS

PRESS

2

• Press the release buttons near each leg and pull to remove each leg.

Seat

1

Hint: If you are converting to toddler seat from high chair mode,
follow steps 1 and 2.

• While pulling the release handles on the sides of the tray, pull the
tray towards you and lift to remove it from the seat.

Toddler Seat Base

3

Hint: If you are converting to toddler seat from infant seat or swing
modes, remove the seat from the infant seat base or swing seat base.

• Fit the seat onto the toddler seat base.

• Push to “snap” the seat onto the base. Pull up on the seat to be

sure it is secure.

4

• Store the restraint system underneath the pad.

• Unbuckle the restraint system.

• Push the waist and crotch belts back through the slots in the pad.

Restraint System

18

Infant Seat, Infant Swing and High Chair

Restraint System Use

Waist Belt

1

Securing Your Infant

• Place your child in the seat. Position the crotch belt between
your child’s legs.

• Fasten the waist belts to the crotch belt. Make sure you hear a

“click” on both sides.

• Tighten each waist belt so that the restraint system is snug
against your child. Please refer to step 3 for instructions to
tighten the waist belts.

• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.

Crotch Belt

Waist Belt

Free End

Anchored End

3

To tighten the waist belts:

• Feed the anchored end of the waist belt up through the buckle to
form a loop

To loosen the waist belts:

• Feed the free end of the waist belt up through the buckle to form a
loop
the buckle. Pull the anchored end of the waist belt to shorten the
free end of the waist belt

Adjuster

A

. Pull the free end of the waist belt

A

. Enlarge the loop by pulling on the end of the loop toward

B

.

Free End

Anchored End

LOOSENTIGHTEN

B

.

Adjuster

Waist Belt

Waist Belt

2

• Adjust the length of the crotch belt so that the waist belts rest on
baby's belly button.

• Please refer to step 4 in this section for instructions on how to
shorten or lengthen the crotch belt.

4

To shorten the crotch belt:

• Hold the adjuster and pull the rear crotch strap down.

To lengthen the crotch belt:

• Slide the adjuster up.

SHORTEN

LENGTHEN

19

International Packaging & Instructions

& limited space US Packaging

Power Wheels Packaging

& Instructions

CONSU

MER ASSISTAN

CE

1-800-348-0751 (US & Canada)

Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.

BabyGear Instructions

CONS

ASSISTANC

A

CONS

S

YUDA AL
ERVICE À LA CLIENTÈLE

1-800-432-5437 (US & Canada)

Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.

Hearing-impaired consumers/Clientes con problemas auditivos/
Pour les malentendants: 1-800-382-7470.

En México: 59-05-51-00 Ext. 5205 ó 01-800-463-59-89

CANADA

Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.

MÉXICO

Importado y distribuido por Mattel de México, S.A. de C.V.,
Insurgentes Sur #3579, Torre 3, Oficina 601, Col. Tlalpan,
Delegación Tlalpan, C.P. 14020, México, D.F. R.F.C. MME-920701-NB3.

CHILI

Mattel Chile, S.A., Avenida Américo Vespucio 501-B, Quilicura, Santiago, Chile.

UMER

VENEZUELA

Mattel de Venezuela, C.A., RIF J301596439, Ave. Mara, C.C. Macaracuay Plaza,
Torre B, Piso 8, Colinas de la California, Caracas 1071.

ARGENTINA

Mattel Argentina, S.A., Curupaytí 1186, (1607) – Villa Adelina, Buenos Aires.

COLOMBIA

Mattel Colombia, S.A., calle 123#7-07 P.5, Bogotá.

E

UMIDOR

Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2010 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.

Fisher-Price, Inc., une liale de Mattel, Inc., East Aurora, New York 14052, É.-U.
©2010 Mattel, Inc. Tous droits réservés. PRINTED IN CHINA/IMPRIMÉ EN CHINE
® et ™ désignent des marques de Mattel, Inc. aux É.-U. T3643pr-0920