Page 1
1
Please keep this instruction sheet for future reference,
as it contains important information.
Requires nine “AA” (LR6) alkaline batteries (not included) for operation.
Adult assembly is required for battery installation.
Tool required for battery installation: Phillips screwdriver (not included).
This product functions with most other Shake ‘n Go™ vehicles. Each sold separately.
www.fisher-price.com
N0246
Page 2
• Slide the tab near the starting gate to release it. Lift the starting gate.
• Set the cars on each starting arrow. The red start light turns on when a
car is placed on a starting arrow.
Tab
Starting Gate
Starting Arrow
Red Start
Lights
Page 3
Ready - Set - Go!
• Lift the light post.
• Once both cars are on the starting arrows the lights on the light post
flash red, yellow and then green to go!
Light Post
Page 4
• Press the pedal next to each car to start the race!
Note: If one car takes off before the green light, you will hear a buzzer
and the lights will reset.
• Shake the cars to start the “engine” and the sound effects.
Note: For maximum distance, shake the car 7 or 8 times. Shaking more
than this does not increase the distance it will travel.
Pedals
Base
Car
Slide the power
switch on each
car and the
base on .
Page 5
Battery Installation
In exceptional circumstances, batteries
may
leak fluids that can cause a chemical
burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries
or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the product. Dispose of
batteries safely. Do not dispose of this
product in a fire. The batteries inside
may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same
or equivalent type, as recommended.
• Do not charge non-rechargeable
batteries.
• Remove rechargeable batteries
from the product before charging.
• If removable, rechargeable batteries
are used, they are only to be charged
under adult supervision.
1.5V x 9
"AA" (LR6)
• Locate the battery compartment on the
bottom of each car and the base.
• Loosen the screw(s) in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
• Insert three, new “AA” (LR6) alkaline
batteries in each car and the base.
Hint: We recommend using alkaline
batteries for longer battery life.
• Replace the battery compartment door
and tighten the screw(s).
• If the cars or the base begin to operate
erratically, you may need to reset the
electronics. Slide the power switch on the
bottom of a car or the base off and then
back on.
• When lights/sounds/motions become
faint or stop, it’s time for an adult to
change the batteries!
Battery Safety Information
• Protect the environment by not
disposing of this product with
household waste (2002/96/EC).
Check your local authority for
recycling advice and facilities
(Europe only).
Car
Base
Page 6
Consumer Information
FCC Statement (United States Only)
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio
or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modifications not
expressly approved by the manufacturer
responsible for compliance could
void the user’s authority to operate
the equipment.
This device complies with Part 15 of the
FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
Care
• When you’re finished playing with this toy,
slide the power switch on the base and
the cars off
.
• Wipe this toy with a clean cloth dampened with a mild soap and water
solution. Do not immerse this toy.
• This toy has no consumer serviceable
parts. Do not take this toy apart.
Storage
• When finished racing, place both cars
on the start arrows on the base.
• Push the light post and starting gate
down to fold for storage.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA N0246pr-0920
Loading...