Fisher-Price P6946 User Manual

P6946

Swing

WARNING

Rocker

IMPORTANT! KEEP

INSTRUCTIONS FOR

FUTURE REFERENCE.

Infant Seat

www.fi sher-price.co.uk

Consumer Information

WARNING

To prevent injury or death from
falls or being strangled in the
restraint system

• Never leave child unattended.

When used as a Swing:

• Always use the restraint system.

• Never use with an active child who may
be able to climb out of the product.

When used as an Infant Seat
or Rocker:

• Fall Hazard - It is dangerous to use
this product on an elevated surface.
Use only on a floor.

• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion)
since the product can tip over and
cause suffocation in soft surfaces.

• Always use the restraint until child
is able to climb in and out of the
product unassisted.

• Never use as a carrier. Never use the
toy bar as a handle.

• Infant seat and swing modes not
recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).

• Use the Rocker position only when
child has developed enough upper
body control to sit without
leaning forward.

• IMPORTANT! PLEASE KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE, AS THEY CONTAIN
IMPORTANT INFORMATION.

• Please read these instructions before assembly and use of
this product.

• Adult assembly is required. Tools needed for assembly:
Phillips screwdriver (not included) and assembly tool (included).

• Requires four “D” (LR20) alkaline batteries (not included) for
swing operation.

• In Swing mode, only to be used by children that cannot climb
out of seat.

• In Infant Seat and Rocker mode, designed for use with children
from birth to 9 kg (20 lbs).

• In Rocker mode, always use restraint until your child is able to
climb in and out of the chair unassisted.

• Product features and decoration may vary from photos.

Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.

Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.

New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre,

Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P)

Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country
Resort, 47410 PJ. Tel: [phone], Fax: [phone].

2

Parts

IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed inside the pad.

Toy Bar (Toys may be different)

Seat Back Tube

2 Retainers
(with Lock Nut)

Cross Brace

Pad

2 Side Rails
with Waist Belts

2 Retainers (with Lock Nut)

2 Seat Tubes

Housing

2 Legs

Seat Tube Support

Motor Housing

Front Tube

Kickstand

Assembly Tool (This tool is not a toy. Please throw away
after assembly is complete.)

Back Base

Front Curved Base

Note: Tighten or loosen screws with a Phillips screwdriver
or the assembly tool. Do not over-tighten the screws.

#4 x 3,18 cm Screw – 2M5 x 2,9 cm Screw – 4

Shown Actual Size

IMPORTANT! Before assembly, inspect this product for damaged

hardware, loose joints, missing parts or sharp edges. DO NOT
use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never
substitute parts.

3

Infant Seat/Rocker Assembly

PRESS

CAUTION

This package contains small parts

in its unassembled state.

Adult assembly is required.

Cross Brace

PRESS

1

• While pressing the tab on each end of the cross brace, insert the
cross brace into the side rails, as shown. Make sure you hear
a “snap” on each side.

Side Rails

PRESS

Side Rail Hole

Front Tube

Side Rail Hole

3

• Insert a M5 x 2,9 cm screw through the outside of each side rail
and into the ends of the front tube.

IMPORTANT! Please follow the next assembly (step 4) carefully to
completely secure the front tube to the side rails.

Retainer with Lock Nut

Front Tube

Side Rail Hole

2

• Locate the hole in each side rail.

• Position the front tube so that it is a shape.

• Fit the front tube to the side rails, as shown. Hold the front tube
in place and proceed to step 3.

4

• Fit a retainer with lock nut onto the end of a screw and to the
inside of a side rail. Tighten the screw using the assembly tool.
Turn the tool clockwise to tighten.

Hint: A lock nut has been factory assembled to the retainer.
During shipment, the lock nut may have fallen out of the retainer.
If it has, please fit it into the hexagonal hole in the retainer so that
the rounded side of the lock nut faces out.

• Repeat this procedure to fasten the screw to the other end of
the front tube and side rail using another retainer with lock nut.

4

Seat Back Tube

Infant Seat/Rocker Assembly

PRESS

Lower Pocket

Sockets

5

• Insert the seat back tube into the socket in each side rail.

• While pressing the tabs on the ends of the seat back tube,
continue to insert the seat back tube into the sockets in each
side rail until the tabs “snap” into place. Make sure you hear

a “snap” on each side.

• Pull the seat back tube up to be sure it is secure in the side
rail sockets.

Hardboard

Upper Pocket

Seat Back Tube

7

• Fit the upper pocket on the pad onto the seat back tube.

• Turn the hardboard over and insert it into the slot in the front
edge of the pad.

PRESS

PRESS

Kickstand

6

• While pressing the tab on each end of the kickstand, insert the
kickstand into the small tube inside each side rail.

Hint: The kickstand is designed to fit into the siderails one way.
If you cannot insert it into the small tubes (inside the side rails),
turn it around and re-insert it into the small tubes.

• Push the kickstand into the small tubes until the tabs “snap”
into place. Make sure you hear a “snap” on each side.

• Pull the kickstand to be sure it is secure in each side rail.

5