Fisher-Price P4259 User Manual
P4259
www.fisher-price.com
Consumer Information
WARNING
Prevent serious injury or death from falls or
sliding out.
• The child should be secured in the high
chair at all times by the restraint system,
either in the reclining or upright position.
The restraint belts must be adjusted to fit
your child snugly. The tray is not designed
to hold the child in the chair.
• It is recommended that only children
capable of sitting upright unassisted use the
high chair in the upright position.
• Always keep child in view while using the
high chair.
• Never leave child unattended.
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
IMPORTANT! Please keep these instructions for future reference.
Please read these instructions before assembly and use of •
this product.
Adult assembly is required. Tool needed for assembly: •
Allen wrench (included).
Product features and decorations may vary from photographs. •
2
Parts
Food Tray Snack Tray
2 Front Legs 2 Back Legs
Footrest
Seat Back with Shoulder
and Waist Belts
Seat Bottom with
Crotch Belt
Back Base
Front Base
M4 x 17mm Screw – 6
M6 x 28mm Screw – 8
Tighten the screws with the enclosed Allen wrench.
Seat Pad
M5 x 60mm Screw – 6
All Fasteners Shown Actual Size
2 Seat Brackets
Allen Wrench
M6 x 15mm Screw – 2
3
Assembly
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never substitute parts.
Back Leg
Seat Bottom
Large Socket
Back Leg
1
Turn the seat bottom upside down on a flat surface. •
Position a back leg so that it curves up and fit it into a large •
socket in the seat bottom.
Hint: If the leg does not seem to fit into the seat bottom socket,
try the other back leg.
PUSH
M5 x 60mm
Screw
3
Fit the other back leg into the large socket in the seat bottom.•
PUSH
M5 x 60mm
Screw
2
Insert an M5 x 60mm screw into the side of the seat bottom •
and tighten.
Push the back leg until it• "snaps" in place.
4
Insert an M5 x 60mm screw into the side of the seat bottom •
and tighten.
Push the back leg until it • "snaps" in place.
4
Assembly
Front Leg
Small Socket
5 7
Front Leg
Seat Bottom
Position a front leg so that it curves up and fit it into the small •
socket in the seat bottom.
Hint: If the leg does not seem to fit into the seat bottom, try the
other front leg.
M5 x 60mm
Screws
Fit the other front leg into the small socket in the seat bottom. •
M5 x 60mm
Screws
6
Insert two M5 x 60mm screws into the other side of the seat •
bottom and tighten.
8
Insert two M5 x 60mm screws into the side of the seat bottom •
and tighten.
5
Assembly
Back Base
M6 x 28mm
Screws
Back Legs
M6 x 28mm
Screws
9
Fit the back base onto the bottom of both back legs, as shown. •
Insert two M6 x 28mm screws into• each back leg and tighten.
Posts
Footrest
11
Fit the sockets on the footrest onto the posts on the front of •
the assembly.
Slide the footrest up onto the posts.•
Hint: You may want to lower the seat to assemble the footrest.
Refer to page 13 for instructions to lower the seat.
Front Legs
10
BACK VIEW
M6 x 28mm
Screws
M6 x 15mm Screws
M6 x 28mm
Screws
Front Base
Fit the front base onto the bottom of both front legs. •
Insert two M6 x 28mm screws into • each front leg and tighten.
Turn the assembly upright. •
12
While holding the footrest in place, insert two M6 x 15mm screws •
into the holes on the back of the footrest and tighten.
6
Loading...