Page 1
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three “AA” (LR6) alkaline batteries for operation (not included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
1
www.fisher-price.com
Page 2
Assembled Parts
CAUTION
This product contains small parts in its unassembled state.
Adult assembly is required.
Bird’s NestTree Top Bird
Tree Trunk – 2 Pieces
Base
Ramp – 3 Pieces
#6 x 1/2" Screw – 4
Shown Actual Size
Tighten all screws with a Phillips
screwdriver. Do not over-tighten
the screws.
2
Page 3
Battery
Battery Safety
Installation
1.5V x 3
“AA” (LR6)
• Locate the battery compartment on the
top of the toy.
• Loosen the screws in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
• Insert three “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline
batteries for longer battery life.
• Replace the battery compartment door
and tighten the screws with
a Phillips screwdriver.
• If the toy begins to operate erratically
you may need to reset the electronics.
Slide the power/volume switch off and
then back on.
• When sounds from this toy become faint
or stop, it’s time for an adult to change
the batteries.
• Protect the environment by not
disposing of this product with
household waste (2002/96/EC).
Check your local authority for
recycling advice and facilities
(Europe only).
Information
In exceptional circumstances, batteries
may leak fluids that can cause a chemical
burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the product. Dispose
of batteries safely. Do not dispose of
product in a fire. The batteries inside
may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or
equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the
product before charging.
• If removable, rechargeable batteries are
used, they are only to be charged under
adult supervision.
3
Page 4
Consumer Information
FCC Statement (United States Only)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there
is no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try
to correct the interference by one or more
Care
• Wipe this toy with a cloth clean. Do not
use water or other liquids to clean.
Do not immerse.
• This product has no consumer serviceable
parts. Do not take this toy apart.
ICES-003
• This Class B digital apparatus complies
with Canadian ICES-003.
• Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
NMB-003
• Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’utilisateur du dispositif doit être prêt
à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible
de compromettre le fonctionnement
du dispositif.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. P1532a-0920
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modifications not expressly
approved by the manufacturer responsible
for compliance could void the user’s authority
to operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
4
Page 5
Assembly
Tree Trunk Pieces
1
• Fit the tree trunk pieces together. Push to
“snap” them in place.
Bird’s Nest
3
Tree Trunk
Base
2
• Insert and “snap” the tree trunk into the
center of the base.
Hint: The tree trunk only fits into the base
one way. If it does not seem to fit, turn it
around and try again!
• Fit the bird’s nest onto the top of the tree
trunk. Push to “snap” it in place.
Ramp 1
4
• Slide the ramp labeled 1 onto the bottom
of the tree trunk.
• Insert the tab on ramp into the slot in the
base. Push to “snap” in place.
5
Page 6
Assembly
Screw
5
• Insert a screw into the hole under ramp 1
and tighten.
Ramp 2
Ramp 1
6
• Slide the ramp labeled 2 onto the tree trunk.
• Insert the tab on ramp 2 into the end of
ramp 1. Press the ends to “snap”
them together.
Screws
7
• Insert two screws into the holes under
ramp 2 and tighten.
Ramp 3
Ramp 2
8
• Slide the ramp labeled 3 onto the tree trunk.
• Insert the tab on ramp 3 into the end of
ramp 2. Press the ends to “snap”
them together.
6
Page 7
Assembly
Bird's Nest
Ramp 3
9
• “Snap” the top of ramp 3 onto the
bird’s nest.
Screw
Bird
Tree Top
11
• Insert and “snap” the tree top onto the
bird’s nest.
Hint: The tree top only fits one way. If it
does not seem to fit, turn it around and
try again!
• Insert and "snap" the bird into the hole
in the bird's nest.
10
• Insert a screw into the hole under ramp 3
and tighten.
7
Page 8
A Jungle of Fun!
Power/Volume
Switch
Roller
Power/Volume
Switch
Power/Volume
Switch
• Slide the power/volume switch to ON with low volume , ON with high
volume , or when finished using the product, slide the switch OFF .
• Place an animal in the tree house. Let go and listen to fun tunes as the
animal rolls down the ramp.
• Spin the roller for more fun tunes and sound effects.
8
Loading...