Fisher-Price N7630 Instruction Sheet

Page 1
Sit & Play
Stand & Walk
1
www.fisher-price.com
Page 2
Assembled Parts
CAUTION
This product contains small parts in its unassembled state.
Adult assembly is required.
3
#8 x
/4" Screw – 8
Shown Actual Size
Tighten all screws with a Phillips
Handle
screwdriver. Do not over-tighten the screws.
Activity Panel
2 Bases
2
Page 3
Battery
Battery Safety
Replacement
1.5V x 3
“AA” (LR6)
For best performance, we recommend replacing the batteries that came with this toy with three, new "AA" (LR6) alkaline batteries.
• Locate the battery compartment on the back of the toy.
• Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door.
• Remove the exhausted batteries and throw them away.
• Insert three “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws with a Phillips screwdriver.
• If the toy begins to operate erratically you may need to reset the electronics. Slide the power/volume switch off and then back on.
• When sounds or lights from this toy become faint or stop, it’s time for an adult to change the batteries.
Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.
3
Page 4
Handle
Assembly
1
Activity Panel
• At an angle, fit the handle to the activity panel. Rotate the handle down to fit the holes in the handle to the pegs on the activity panel.
Handle
Retainer
2
• Place the handle retainer on top of the handle.
• Insert four screws into the handle retainer and tighten.
3
Bases
• Fit the activity panel into each base.
Hint: The activity panel will only fit in each base one way. If it does not seem to fit, turn it around and try again!
4
• Carefully turn the assembly over.
• Insert two screws into each base and tighten.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. N7630pr-0920 ©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO
4
Page 5
2-in-1 Fun!
Slide the power/volume
switch to on with low
volume , on with high
volume or off .
Sit & Play
• Press the buttons on the piano and saxophone, or slide the guitar switch for tunes and musical scats.
• Turn the page on the book for sing-along songs.
• Watch the dancing lights while you listen to the tunes.
Slide the mode switch
to Sit & Play or
Stand & Walk .
Stand & Walk
• Push the walker for fun music and dancing lights.
5
Page 6
Consumer Information
• Please keep this instruction sheet for future reference, as it contains important information.
• Requires three “AA” batteries for operation (included).
• Adult assembly is required. Tool required for assembly: Phillips screwdriver (not included).
Care
• Wipe this toy with a damp cloth. Do not immerse.
• This product has no consumer serviceable parts. Do not take this toy apart.
Protect the environment by not
disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only).
ICES-003
• This Class B digital apparatus complies with Canadian ICES-003.
• Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
NMB-003
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
6
Loading...