M6711
WARNING
IMPORTANT!
KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
www.fi sher-price.co.uk
Consumer Information
WARNING
To prevent serious injury and/or
falls and being strangled in the
restraint system:
• Always use the restraint system.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product on
an elevated surface.
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
Care
• GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303;
www.service.mattel.com/uk.
• Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
• New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
• Asia: Mattel East Asia Ltd, Room 1106, South Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China.
• Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: 03-78803817,
Fax: 03-78803867.
Care
The pads and toys are machine washable. Wash them separately
in cold water on the gentle cycle. Do not use bleach. Tumble
dry separately on low heat and remove promptly. The
frame and toy bar can be wiped clean using a mild cleaning
solution and a damp cloth. Do not immerse this product.
To remove the pad:
• Lift the seat bottom tube and remove the pad lower pocket.
• Push the restraint belts back through the pad.
• Turn the product face down. Unfasten the buckle, and turn
the product upright again.
• Slide the pad upper pocket off the seat back tube.
To re-assemble the pad:
• Refer to assembly steps 8 and 9.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.
• Tool required for assembly: Phillips screwdriver (not included).
• Requires four “C” (LR14) alkaline batteries for operation
(not included).
• Weight Limit: 9 kg (20 lbs).
IMPORTANT! The maximum weight limit for this product is
9 kg (20 lbs). If your child weighs less than 9 kg (20 lbs), but is
really active and appears to be able to climb out of the swing,
immediately discontinue its use.
• Product features and decoration may vary from photo.
©2007 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.. PRINTED IN CHINA
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. M6711pr-0726
2
Parts
Adjustable Pillow
Assembly
IMPORTANT! Please remove all parts from the package
and identify them before assembly. Some parts may be
packed in the pad.
2 Swing Frames
Hint: To allow the product
to swing properly, the swing
arm-to-frame (with power
switch) connection is
designed to be loose.
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.
Front Leg
Back Leg
1
Seat Frame
Adjustable Pillow
2 Base Tubes
Seat Pad
Toy Bar
2 Toys
• Slide the front and back legs on the swing frame out until
they “click” into place.
• Repeat this procedure to open the other swing frame.
Press Buttons
on Front Legs
Base Tube
2
#6 x 3 cm Screw – 2
Shown Actual Size
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
• While pressing the buttons on each front leg, insert the
front legs into the base tube.
• Push the front legs down into the base tube until the
buttons “click” into place.
3
PULL UP
Base Tube
Assembly
PULL UP
Base Tube
3
• While standing on the base tube, pull the front legs up. The
front legs should remain secured to the base tube. If you
can remove the front legs, you have not assembled them
correctly to the base tube. Re-read and repeat assembly
step 2.
Press Buttons
on Back Legs
Base Tube
4
5
• While standing on the base tube, pull the back legs up.
The back legs should remain secured to the base tube.
If you can remove the back legs, you have not assembled
them correctly to the base tube. Re-read and repeat
assembly step 4.
Seat Frame
Frame Hubs
Seat Hubs
• While pressing the buttons on each back leg, insert the
back legs into the remaining base tube.
• Push the back legs down into the base tube until the
buttons “click” into place.
6
• Position the seat frame so that the tubes are upright,
as shown.
• While gently pulling the seat hubs out, fit them to the
matching frame hubs.
Hint: If the hubs do not fit together, simply turn the seat
frame around and try again!
4
Assembly
Seat Hub
Seat Hub
7
• Insert a screw through the outside of each seat hub.
Tighten the screws.
Pad Upper
Pocket
Pad Lower Pocket
Seat Bottom Tube
9
• Fit the pad lower pocket onto the seat bottom tube,
as shown.
• Lift the seat bottom tube and buckle the straps on the
pad together. Make sure you hear a "click".
Seat Back Tube
Waist Belts
Slots
Waist Belt
8
• Fit the pad upper pocket over the seat back tube.
• From behind the assembly, insert the waist belts through
the slots in the pad.
Toy Bar
Socket
10
• Insert and “snap” the peg on the toybar into the socket
on the swing arm. Pull the toy bar up to be sure it is secure.
• Fit the toy strings up through the slots in the toy bar leaf.
Assembly is now complete.
5
Battery Installation
Hint: We recommend using alkaline batteries for
longer battery life.
Note: Low battery power may cause product movement
to slow and sound volume to become faint or turn off all
together. If this should happen, please remove and discard
all four batteries and replace with four, new “C” (LR14)
alkaline batteries.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids
that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of this product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removeable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Battery Compartment Door
• Locate the battery compartment door on the frame.
• Loosen the screws in the battery compartment door.
• Remove the battery compartment door.
• Insert four "C" (LR14) alkaline batteries.
• Replace the battery compartment door and tighten
the screws.
• Protect the environment by not disposing of the product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
6
Securing Your Child
WARNING
To prevent serious injury and/or
falls and being strangled in the
restraint system:
• Always use the restraint system.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product on
an elevated surface.
Adjustable Pillow
Waist Belt
Buckle
Restraint Pad
• Place your child in the seat. Position the restraint pad
between your child’s legs.
• Fasten both waist belts to the buckles on each side of the
restraint pad. Make sure you hear a “click” on both sides.
• Check to be sure the restraint system is securely attached
by pulling it away from your child. The restraint should
remain attached.
IMPORTANT! The maximum weight limit for this product
is 9 kg (20 lbs). If your child weighs less han 9 kg (20 lbs),
but is really active and appears to be able to climb out of
the swing, immediately discontinue its use.
• Place the pillow on the strap and press into place.
Hint: You can move the pillow up or down for
baby's comfort.
Anchored EndAnchored End
A
B
Free End
TIGHTEN LOOSEN
To tighten the belts: Feed the anchored end of the belt up
through the buckle to form a loop A. Pull the free end of
the belt B. Repeat this procedure to tighten the other belt.
To loosen the belts: Feed the free end of the belt up
through the buckle to form a loop A. Enlarge the loop by
pulling on the end of the loop toward the buckle. Pull the
anchored end of the belt to shorten the free end of the belt
B. Repeat this procedure to loosen the other belt.
Please Note: After adjusting the belts to fit your child, make
sure you pull on them to be sure they are securely fastened.
B
A
Free End
7
Swinging and Music
Storage
Music Switch
Power Switch
• Place your child in the seat and secure properly.
Hint: After turning on power, this product may not swing
unless there is a child in the seat.
• Slide the power switch to any of five speed settings.
• Give the seat a light push to start the swinging motion.
Adjust the power switch to the desired swing motion setting.
Hint: As with most battery-powered swings, a heavier child
will reduce the amount of swinging motion on all settings.
In most cases, the low setting works best for a smaller child
while the high setting works best for a larger child.
• If swinging stops while using a lower setting, try a higher
setting. Give the seat a light push to start the swinging
motion again.
• Slide the music switch to on with low volume ; on with
high volume or off .
• Be sure to turn this product off when not in use. Slide
the power switch to the off setting .
• Make sure your child is properly secured in the swing seat.
• Grasp both handles, as shown, and lift.
• Carefully carry the swing to another room. Be sure to set
the swing down on a non-elevated, flat surface.
• Lift the seat bottom.
• Press the frame release buttons on the inside of the frames
and push the front legs inward.
8
Loading...