Fisher-Price L7345 Instruction Sheet

Please keep this instruction sheet
for future reference, as it contains
important information.

Adult assembly is required
to install batteries.

Tool needed for
battery installation:
Phillips screwdriver
(not included).

Requires three “AA”
batteries (included)
for operation.

1

www.fisher-price.com

Consumer Information

WARNING

To prevent child from climbing

out of a crib/cot, remove this

product from crib/cot once child

can sit up unassisted or can pull

to a standing position.

• Always attach all provided fasteners
(strings, straps, clamps, etc.) tightly to
a crib/cot or playpen according to the
instructions. Check frequently.

• Do not add additional strings or straps
to attach to crib/cot or playpen.

2

Attaching to a Crib/Cot

Mattress

Mattress

MattressMattress

• Position this toy against the rails
(on the inside of baby’s crib/cot) near
the mattress.

Hint: For newborns, place this toy along
a side rail where baby can easily hear
and see it. For infants, place this toy
near baby’s feet (within reach).

• Tie each fastener to fit snugly around

a crib/cot rail.

MattressMattress

Note: It is better to tie the straps in a knot
than a bow, since a bow may be
easily untied.

3

Play Time!

Volume SwitchMode Switch

• Slide the mode switch to: Learn , Short Tune , Music or Off .

• When baby kicks or presses the pig, cow or chick’s feet:

Listen to a fun sound, song or farm animal identified.

Baby enjoys a short tune.

Sing-along to original songs.

Hint: Baby enjoys an oink-oink, moo-moo or peep-peep with each kick in Short Tune or
Music modes!

• Adjust the volume to high or low for your child’s comfort. The volume switch is
located on the back of the toy. Simply open the fasteners to access the switch.

• Remove the toy from the crib/cot to extend play as baby grows!

Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. PRINTED IN CHINA
©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. L7345a-0920

4

Battery Replacement

Battery Compartment Door

Battery Compartment DoorBattery Compartment Door

For best performance, we recommend
that you replace batteries that came
with this toy with three, new “AA”
(LR6) alkaline batteries.

• Open the fasteners on the fabric cover
on the back of the toy.

• Loosen the screws in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.

Hint: You may need to use the tip of
the screwdriver to lift the battery
compartment door.

• Remove the worn batteries and dispose
of them properly.

• Insert three “AA” (LR6) alkaline batteries.

Hint: We recommend using alkaline
batteries for longer battery life.

• Replace the battery compartment door
and tighten the screws with a Phillips
screwdriver. Do not over-tighten.

• Press to secure the fasteners on the
fabric cover.

• When sounds or lights become faint
or stop, it’s time for an adult to change
the batteries!

• Protect the environment by not
disposing of this product with
household waste (2002/96/EC).
Check your local authority for
recycling advice and facilities
(Europe only).

Battery Safety

1.5V x 3

"AA" (LR6)

In exceptional circumstances, batteries
may leak fluids that can cause a chemical
burn injury or ruin your toy. To avoid
battery leakage:

• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).

• Insert batteries as indicated inside the
battery compartment.

• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the toy. Dispose of batteries
safely. Do not dispose of the product in
a fire. The batteries inside may explode
or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or
equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the
toy before charging.

• If removable, rechargeable batteries are
used, they are only to be charged under
adult supervision.

5

Care

PUSH

PUSH

• Hand wash the fabric cover in cold water
with a mild detergent. Do not use bleach.
Line dry. Do not machine wash or place
in a dryer.

• Surface clean the plastic toy by wiping it
with a damp cloth. Do not immerse the
plastic toy.

• To remove the fabric cover, open the
fasteners on the back of the toy. Push
both tabs, one at a time, toward the
unlock position
pull the plug(s) on the fabric cover from
the front of the plastic toy. Remove the
fabric cover.

• To replace the cover, first place the plastic
toy into the fabric cover. Then, fit and
snap the plugs (one at a time) on the
fabric cover into the slots in the plastic toy.
You should hear a “click”. Pull gently on
the fabric cover to be sure it is attached to
the plastic toy.

• Press to secure the fasteners on the back
of the toy.

. At the same time,

FCC Statement

United States Only

This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference ina residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there
is no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the
equipment and receiver.

• Consult the dealer or an experienced
radio/TV technician for help.

Note: Changes or modifications not
expressly approved by the manufacturer
responsible for compliance could void the
user's authority to operate the equipment.

6