L7334
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three “D” (LR20) alkaline batteries for
mobile and two "AAA" (LR03) alkaline batteries for
remote (batteries not included) operation.
Adult assembly is required.
Tool required for assembly:
Phillips screwdriver (not included).
www.fisher-price.com
Consumer Information
WARNING
Possible entanglement injury.
• Keep out of baby’s reach.
• Remove mobile portion of product from crib or playpen
when baby begins to push up on hands and knees.
• This product will not attach to all crib designs. Do not add
additional strings or straps to attach to crib or playpen.
• The mobile portion of a product may be used from birth until 5 months.
• The base portion of product may be used from birth until 36 months.
• A crib mobile is intended for visual stimulation and is not to be grasped by a child.
• Always attach with all provided fasteners (clamp) tightly to a crib or playpen according
to the instructions. Check frequently.
• Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not
immerse this toy.
• This toy has no consumer serviceable parts. Do not take this toy apart.
2
Parts
Crib AdaptorBase
3 Soft Animals Clamp
Mobile Hub
Remote
3 Soft Stars
Arm
Note: All of the screws used to assemble this toy are located in the product.
Follow these instructions carefully to fully secure the screws. Tighten and loosen
all screws with a Phillips screwdriver. Do not over-tighten.
3
Base Battery Installation
1.5V x 3
“D” (LR20)
• Locate the battery compartment on the back of the base.
• Loosen the screws in the battery compartment door and lift to remove it.
Hint: If the crib adaptor is attached to the base, loosen the screws in the crib adaptor and
remove it first.
• Insert three “D” (LR20) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws.
IMPORTANT! Under normal use conditions, the batteries in the base will require
replacement more often than the batteries in the remote. When sounds or light become
faint or movement of the mobile is sluggish, it’s time for an adult to replace the batteries
in the base.
4
Remote Battery Installation
1.5V x 2
"AAA" (LR03)
• Locate the battery compartment on the back of the remote.
• Loosen the screw in the battery compartment door and lift to remove it.
• Insert two "AAA" (LR03) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screw.
IMPORTANT! If the mobile does not respond to the remote, it does not mean that the
battery power in the remote is low. Replace the batteries in the remote if the LED signal
indicator on the remote is dim when the button is pressed. If the LED signal indicator
does not light after installing new batteries in the remote, check the orientation of the
batteries in the battery compartment to make sure they are properly installed.
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities
(Europe only).
5
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
FCC Statement
United States Only
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful inter-ference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user's authority to operate the equipment.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. L7334a-0920
©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA
6
Assembly
PRESS
SLIDE
Base
1
• Fit the crib adaptor to the base.
• Tighten all four screws in the crib adaptor.
PRESS
PRESS
Crib Adaptor
Arm
SLIDE
SLIDE
Socket
Base
2
• First press the button next to the socket and then slide the socket door open .
• Fit the arm into the socket in the base.
• Tighten both screws in the arm.
7
Assembly
Mobile
Hub
3
• Fit the mobile hub onto the end of the arm.
• Tighten both screws in the arm to secure the mobile hub.
Soft Animal
4
Attach Soft Animals
• Fit the string on a soft animal through the slot in the end of outer spoke (larger).
• Pull down gently on the soft animal to secure the string in the outer spoke.
• Repeat this procedure to attach the remaining soft animals to the other two outer spokes.
Attach Soft Stars
• Fit the string on a soft star through the slot in the end of inner spoke (smaller).
• Pull down gently on the soft star to secure the string in the inner spoke.
• Repeat this procedure to attach the remaining soft stars to the other two inner spokes.
Soft Star
8
Crib Attachment
Base
Crib Top Rail
Clamp
• Fit the base onto the crib top rail, so that the threaded peg extends outside the crib.
• Fit the clamp onto the threaded peg and turn the clamp clockwise to secure the base to
the crib. Do not over-tighten the clamp.
Mattress
At least 7 inches
Bottom of Base
• If the distance between the base and the mattress is less than 7 inches (18 cm), lower
the crib mattress.
9
Use
Base Dome
• When using the remote, make sure that the arrow on the base dome is pointing towards
the transmitter window on the remote. For best results, make sure the path between
the transmitter window on the remote and the dome on the base are in a direct line
and free of obstacles. Rotate the base dome so that the arrow points to the area from
which you’re most likely to use the remote. For example, if you’ll most often be using
the remote from the doorway of the nursery, make sure that the arrow on the base
dome is pointing towards the doorway and that the path between the base dome and
the doorway is free from obstructions.
IMPORTANT!
• In the unlikely event that use of the remote interferes with normal use of other remote
controlled equipment, such as televisions and stereos, or use of other electric or
battery powered appliances interfere with operation of the mobile, do not use both
appliances at the same time.
• For best performance between the base and the remote, avoid using the remote in
areas of bright light. In bright natural or artificial light, you may notice loss of range.
Move the base or otherwise reduce the amount of light to improve performance.
10
Classical Music, Soothing Lullabies, Lights and Motion
Dome/Lights Control Button
Power/Volume Switch
Mode Select Switch
Music Select Buttons
Dome/Lights Control Button
Press this button to turn the soothing night light on.
Press again to turn the night light off.
Hint: Be sure the power/volume switch is set to an on position.
Power/Volume Switch
Choose from four settings:
off
; on with low volume ;
on with medium volume
or on with high volume
Mode Select Switch
Slide the switch to select one
of three modes:
Music, motion and
projected lights
Music and motion
Music only
.
;
Music Select Buttons
Choose classical music from
Bach, Mozart, Beethoven or
soothing lullabies.
• Press the button on the remote to
activate music, lights and motion.
Press again to stop.
Note: The remote will remain active for
about one hour. After an hour, you will
need to slide the power/volume switch
on the mobile off, then on again
to reactivate.
11
Convert to a Cribside Night Light
Remove the mobile and use as a music box with a night light!
• Loosen both screws in the arm near
the base.
• Lift and remove the arm from the base.
• Close the small door on top of the base.
Store the mobile in a safe place for
future use.
12
Loading...