Fisher-Price L3891 User Manual

L3891

IMPORTANT!

KEEP INSTRUCTIONS

FOR FUTUREREFERENCE.

www.fisher-price.com.au

Consumer Information

WARNING

Prevent serious injury or death from falls
or sliding out:

• Always use the restraint system for the
upright and reclined positions of the seat.
Adjust restraint to fit your child snugly.
The tray is not designed to hold the child
in the chair.

• It is recommended that only children
capable of sitting upright unassisted use
the upright position of the high chair.

• Position the high chair away from steps,
hot surfaces, electrical cords and other
items that may cause injury to the child.

• Always leave wheels locked.

• Always keep child in view while in
high chair.

• Never leave child unattended.

• Follow the manufacturer’s instructions.

IMPORTANT! Place the high chair on a level, stable surface
away from electrical flexes. Be sure to keep electrical flexes
out of child's reach.

• Please read these instructions before assembly and use of
this product.

• Adult assembly is required. Tool needed for assembly:

Phillips screwdriver (not included).

• Weight limit: 22,7 kg (50 lbs).

• Product features and decorations may vary from photos.

• Australia: Mattel Australia Pty. Ltd., 658 Church Street,

Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.

New Zealand: 16-18 William Pickering Drive, Albany 1331,

•

Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,

•

World Finance Centre, Harbour City, Tsimshatsui,
HK, China.

Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd

•

Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe,
Persiaran Tropicana Golf Country Resort, 47410 PJ.
Tel: [phone], Fax: [phone].

CAUTION

This package contains small parts in
its unassembled state. Adult assembly
is required.

2

2

Parts

Pad

Seat Bottom

Footrest

Seat Back

Back Base

Hinge Rod

2 Frames

Front Base

2 Seat Bottom Tubes

Base TrayFood Tray

Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.

#8 x 1,9 cm Screws - 8

#10 x 2,2 cm Black Screws - 7

Shown Actual Size

3

Teether Toy

Assembly

IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.

Footrest

Seat Bottom

1

• Place the seat bottom face down on a flat surface.

• At an angle, fit the footrest to the seat bottom, as shown.

Plastic Rings

Seat Bottom Tubes

2

• Slide a seat bottom tube through each set of plastic rings
on the seat bottom.

Plastic Rings

3

• Align the holes in the plastic rings and the seat bottom tubes.

• Insert a #8 x 1,9 cm screw through each plastic ring and into
the seat bottom tubes, as shown. Tighten the screws. This may
require extra force.

• Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly. Remove
the screws and check to be sure the screw holes in the
seat bottom tubes and seat bottom plastic rings are aligned.
Replace and tighten the screws.

4

Assembly

Insert Screws Here

4

• Insert two #10 x 2,2 cm black screws through the

footrest and into the seat bottom. Tighten the screws.

Seat Back Pins

Hinge

Hinge Rod

6

• Turn the seat assembly face down.

• Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.

• Insert a #10 x 2,2 cm black screw into the hinge rod.
Tighten the screw.

• Set the seat assembly aside for Assembly step 10.

Slot

Slot

5

• Turn the seat bottom assembly upright.

• Fit the seat back pins into the slots in the top side of the
seat bottom assembly.

Frame Leg

7

• Pull the frame leg out on each frame to open. Make sure it

"clicks" into place.

5