Fisher-Price L0542 User Manual
L0542
IMPORTANT!
KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
www.fi sher-price.co.uk
Consumer Information
WARNING
Prevent serious injury or death from falls
or sliding out:
• The child should at all times wear a safety
harness correctly fitted and adjusted. The tray
is not designed to hold the child in the chair.
• It is recommended that only children capable
of sitting upright unassisted use the high
chair in the upright position.
• Always keep child in view while in the
high chair.
• Never leave child unattended.
• Do not use the high chair unless all
components are correctly fitted and adjusted.
Prevent injury from burns: Do not place this
high chair near open fires or any hot surfaces.
IMPORTANT! Place the high chair on a level, stable surface
away from electrical flexes. Be sure to keep electrical flexes out
of child's reach.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.
• Tool needed for assembly: Phillips screwdriver (not included).
• Product features and decorations may vary from photographs.
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: +603-3341 9052.
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
2
2
Assembled Parts
Pad Seat Bottom
2 Bases
Seat Back
Footrest
2 Frames
2 Seat Bottom Tubes
Hinge Rod
Food Tray
Base Tray
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
#8 x 1,9 cm Screws – 8 #10 x 2,2 cm Black Screw – 7
Shown Actual Size
3
Teether Toy
Assembly
IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Mattel for replacement parts and instructions if needed.
Never substitute parts.
Footrest
Seat Bottom
1
• Place the seat bottom face down on a flat surface.
• At an angle, fit the footrest on the seat bottom, as shown.
Plastic Rings
Seat Bottom Tubes
2
Plastic Rings
3
• Align the holes in the plastic rings and the seat bottom tubes.
• Insert a #8 x 1,9 cm screw through each plastic ring and into
the seat bottom tubes, as shown. Tighten the screws. This may
require extra force.
• Push the seat bottom tubes back and forth to be sure they are
secured to the seat bottom. If the seat bottom tubes move, you
have probably not fastened them properly. Remove the screws
and check to be sure the screw holes in the seat bottom tubes
and seat bottom plastic rings are aligned. Replace and tighten
the screws.
• Slide a seat bottom tube through each set of plastic rings on
the seat bottom.
4
Insert Screws Here
4
• Insert two #10 x 2,2 cm black screws through the footrest
and into the seat bottom. Tighten the screws. This may require
extra force.
Seat Back Pin
Seat Back Pin
Assembly
Hinge
Hinge Rod
6
• Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back and
seat bottom, as shown.
• Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten
the screw.
• Set the seat assembly aside for Assembly step 9.
Slot
Slot
5
• Turn the seat bottom assembly upright.
• Fit the seat back pins into the slots in the top side of the seat
bottom assembly.
5
Loading...