Fisher-Price J9609 Instruction Sheet

Model J9609

™



www.fisher-price.com

PARTS

PARTS

• Please keep this instruction sheet for future reference, as it contains important information.

• Adult assembly is required.

• Tool needed for assembly: Phillips Screwdriver (not included).

• Hand pump (not included) and inflation pin (included) required to inflate the soccer ball.

• Requires three “AAA” (LR03) alkaline batteries (not included) for operation.

• Please remove all parts from the package and identify them before assembly.

Tube with Tapered End and

Target

Net

Regular End (Upper)

2 Tubes with Tapered Ends

(Upper and Lower)

Pin

Ball

2 Side Tubes

Tube with Tapered End

and Regular End (Lower)

M5 x 28 mm Screw

BOTH SHOWN ACTUAL SIZE

Note: Tighten and loosen all screws with a Phillips

Screwdriver. Do not over-tighten the screws.

2

M5 Lock Nut

ASSEMBLY

ASSEMBLY

Rounded

Side

Tube with Tapered Ends

Tube with Tapered

End and Regular End

1

• Place a tube with tapered end and regular end on a flat surface.

• Fit a tube with tapered ends into the regular end, as shown.

Hint: The tube assembly should form this shape .

• Align the holes in the tubes.

• Fit a lock nut, rounded side out, into the hex hole on the inside of the

tube with tapered end and regular end.

• Insert a screw through the outside of the tube with tapered end and
regular end.

• While holding the lock nut in place, tighten the screw.

Rounded

Side

Side Tube

Tapered

Long End

End

3

• Fit the long end of the other side tube onto the other tapered end of
the assembly.

• Align the holes in the two tubes.

• Fit a lock nut, rounded side out, into the hex hole on the inside of
the side tube.

• Insert a screw through the hole on the outside of the side tube.

• While holding the lock nut in place, tighten the screw.

Rounded

Long End

Tapered

Side Tube

2

2

• Fit the long end of a side tube onto either tapered end of the assembly.

• Align the holes in the two tubes.

Hint: If the holes in the tubes do not align, remove the side tube and place
it on the other end of the assembly.

• Fit a lock nut, rounded side out, into the hex hole in the inside of

the side tube.

• Insert a screw through the hole on the outside of the side tube.

• While holding the lock nut in place, tighten the screw.

End

Side

TOP OF NET

Long Sleeve

Binding

BOTTOM OF NET

4

• Lay the net on a flat surface.

• Note the long sleeve, four short sleeves and the binding around the edge

of the net.

- Long sleeve is the top of the net.

- Binding is the bottom of the net.

3

ASSEMBLY

ASSEMBLY

Short Sleeves

Short Sleeve

5

• Locate the short sleeves near the binding on the bottom of the net.

• First, fit the short sleeve onto the side tube.

• Next, fit the longer side sleeve onto the side tube.

6

• Continue to fit the remaining sleeves onto the side tube.

7

• Slide the sleeves and the net evenly around the frame, as shown.

©2005 ESPN, Inc. All Rights Reserved. www.ESPN.com

Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.

©2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.

PRINTED IN CHINA J9609pr-0920

4

ASSEMBLY

ASSEMBLY

Binding

Long End of Tube

Short End of Tube

Binding

8

• Locate the binding at the bottom of the net.

• Weave the long end of either remaining tube through the openings on the
edge of the net (about half way).

Binding

Binding

Long End of Tube

Short End

of Tube

10

• Weave the long end of the remaining tube through the openings on the
edge of the net.

Short End of Tube

9

• Fit the short end of the tube into the frame assembly.

Short

End of

Tube

11

• Fit the short end of the tube into the frame assembly.

5

ASSEMBLY

ASSEMBLY

Rounded

Side

12

• Fit the ends of the tubes together.

• Fit a lock nut, rounded side out, into the hex hole on the inside of the

tube assembly.

• Insert a screw through the hole in the outside of the tube assembly.

• While holding the lock nut in place, tighten the screw.

14

• Insert the inflation pin into the ball.

• Attach the pump (not included) to the pin.

• Inflate the ball to a circumference of 15 1/2" (39 cm), until firm.
Do not over-inflate.

• After inflating the ball, remove the pin. Store the pin out of the reach of
children for future use.

Assembly is now complete.

Rounded

Side

Sleeves on
Side Tubes

13

• Push the net sleeves down on the side tubes.

• Fit two lock nuts, rounded side out, into the hex hole in the inside of each

side tube assembly.

• Insert a screw into the outside hole in each side tube assembly.

• While holding the lock nut in place, tighten the screw. Repeat this
procedure to fasten the other screw.

6

BATTERY INSTALLATION

BATTERY INSTALLATION

BEGINNER

BEGINNER

Beginner’s score fun sounds when the ball hits the net!

Battery

Compartment

Door

1.5V x 3

"AAA" (LR03)

SHOWN ACTUAL SIZE

• Loosen the screws in the battery compartment door and remove the
battery compartment door.

• Insert three “AAA” (LR03) alkaline batteries into the battery compartment.

Hint: We recommend using alkaline batteries for longer battery life.

• Replace the battery compartment door and tighten the screws.

• When sound becomes faint or there is no sound at all, it’s time for an adult
to replace the batteries!

Power/Mode

Switch

Target

• Locate the power/mode switch on the back of the target. Slide the switch to
1 for beginners.

• Fit the target onto the top edge of the frame.

• Fit the tab on the back of the target onto a net loop.

Tab

Net

Top Edge

of the Frame

BATTERY SAFETY INFORMATION

In exceptional circumstances, batteries may leak fl uids that can cause a
chemical burn injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.

• Remove batteries during long periods of non-use. Always remove exhausted
batteries from the product. Dispose of batteries safely. Do not dispose of
the product in a fire. The batteries inside may explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the product before charging.

• If removable, rechargeable batteries are used, they are only to be charged
under adult supervision.

Scorekeeper

• Your little player hears fun sounds each time
the ball hits the net.

• Turn the knob on the scorekeeper to record your goal!

• When you’re finished playing, slide the power/mode switch on the target
to the off position.

7

PRO

PRO

CONSUMER

CONSUMER

Hit the target like a pro for fun sounds!

Power/Mode
Switch

Move
Target
Up or
Down

Top Edge of

Target

• Locate the power/mode switch on the back of the target. Slide the switch to
2 for more advanced players.

• Fit the target onto the top edge of the frame.

Hint: You can raise or lower the target. Push the target up or down into any of
three positions and secure it by inserting the tab on the back of the target into
the pockets on the back of the target strap.

the Frame

Tab

Pocket

Target

Strap

Back View

of Target

INFORMATION

INFORMATION

CARE

• The frame and net may be wiped clean using a mild cleaning solution and
a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners.
Rinse clean with water to remove residue. Do not immerse this toy.

• To prolong the life of the net, store this toy indoors.

• Periodically check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.

QUESTIONS?

Visit us on-line at www.service.mattel.com.

Or, call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437,
8 AM- 6 PM EST Monday through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470. Write to: Fisher-Price, Inc.,
Consumer Relations, 636 Girard Avenue, East Aurora, New York 14052.

FCC STATEMENT (UNITED STATES ONLY)

Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc­tions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Note: Changes or modifi cations not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate
the equipment.

Scorekeeper

• Hit the target with the ball for fun sounds!

• Turn the knob on the scorekeeper to record your goal!

• When you’re finished playing, slide the power/mode switch on the target to
the off position.

For countries outside the United States:

CANADA: Questions? 1-800-432-5437. Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2;

www.service.mattel.com.

GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303;
www.service.mattel.com/uk

AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.

NEW ZEALAND: 16-18 William Pickering Drive, Albany 1331, Auckland.

ASIA: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.

