Consumer Information
WARNING
To prevent serious injury or death from falls
and being strangled in the restraint system:
• Fall Hazard - It is dangerous to use this
product on an elevated surface, since
child’s movement may cause the product
to slide or tip over. Use only on a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffocation in soft surfaces.
• Always use the restraint system.
• Not recommended for children who can
sit up by themselves (6 months approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• Never use the toy bar as a handle.
Parts
IMPORTANT! Please remove all parts from the package and
identify them before assembly. Some parts may be packed in
the pad.
Headrest Pad
Liner/Pad
Base
Seatback Tube
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
IMPORTANT! Please keep these instructions for future reference,
as they contain important information.
• Please read these instructions before assembly and use of
this product.
• Use from birth until child becomes active and can climb out
of the seat.
• Maximum weight: 9 kg.
• Adult assembly is required.
• Tool needed for assembly: Phillips screwdriver (not included).
• Requires four “D” (LR20) alkaline batteries (not included)
for operation.
Great Britain: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303; www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre,
Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P)
Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country
Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867.
Footrest Tube
Toybar
(Toys may be different)
2 Hubs
Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
#8 x 3,2 cm Screw - 2
Fastener Shown Actual Size
©2006 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. J6982a-0726
2
Battery Installation
Hint: We recommend using alkaline batteries for
longer battery life.
1,5V x 4
“D” (LR20)
Assembly
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel for
replacement parts and instructions if needed. Never substitute parts.
Base Tubes
Lift
Lift
• Loosen the screws in the battery compartment door and remove
the battery compartment door.
• Insert four “D” (LR20) alkaline batteries into the battery compartment.
• Replace the battery compartment door and tighten the screws.
• Low battery power may cause this product to operate erratically
(no movement/no sounds) and the product may not turn off. If this
should happen, remove and discard all batteries and replace with
four, new “D” (LR20) alkaline batteries.
Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.
1
• Lift both base tubes.
Base
Hubs
Base Tubes
Base Tubes
2
• Position the hubs with the smooth side out.
• Fit the hubs onto the base tubes.
Hint: The hubs are designed to fit the base tubes one way. If the
hubs do not fit on the base tubes, check to be sure the smooth side
is out.
• Push the hubs down until you hear a “click”.
• Pull up on the hubs to be sure each is secure.
3