Fisher-Price H7185 User Manual
Cradle
Swing
Swing
(Seat moves
front to back)
H7185
Cradle
(Seat moves
side to side)
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fi sher-price.co.
uk
Consumer Information
WARNING
To prevent serious injury and/or
falls and being strangled in the
restraint system:
• Always use restraint system. Never
rely on the tray to restrain child.
• Please read these instructions before use of this swing.
• Adult assembly is required.
• Tools needed for assembly: Allen Wrench (included) and
Phillips Screwdriver (not included).
• Requires four LR20 (“D”) alkaline batteries for operation
(not included).
• Maximum Weight Limit: 9 kg (20 lbs).
IMPORTANT! If your child weighs less than 9 kg (20 lbs), but is
really active and appears to be able to climb out of the swing,
immediately discontinue its use.
• Product features and decorations may be different than shown
in photos.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product
on an elevated surface.
CAUTION
This product contains small parts
in its unassembled state. Adult
assembly is required.
Care
• Remove the tray from the seat.
• Unbuckle the restraint system.
• Remove the pad elastic loops from the pegs and unfasten
the pad fasteners from the seat.
• Remove the pad from the restraint system.
• Machine wash the pad and toys in cold water with a mild
detergent. Do not use bleach. Tumble dry on low heat and
remove promptly.
• To clean the seat, restraint system, tray, mobile, storage
pouch, toys and motorized frame, use a mild cleaning agent
and damp cloth. Rinse with clean water to remove residue.
• Periodically check the swing for loose fasteners or broken
parts and tighten as needed.
GREAT BRITAIN
Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303; www.service.mattel.com/uk
AUSTRALIA
Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia. Consumer Advisory Service
1300 135 312.
NEW ZEALAND
16-18 William Pickering Drive, Albany 1331, Auckland.
ASIA
Mattel East Asia Ltd, Room 1106, South Tower, World Finance
Centre, Harbour City, Tsimshatsui, HK, China.
MALAYSIA
Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P)
Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf
Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867.
2
Fabric Panel
Parts
Motorized Frame
Allen Wrench
Tray
4 Toys
(toys may be different)
Pad with
Headrest
2 Upper Legs
Lower Seat Tube
Seat with Restraint System
2 Lower Legs
2 Feet
#8 x 1,3 cm Screw - 2
Note: Tighten the screws with the enclosed Allen wrench.
M5 x 30 mm Bolt - 2
ALL SHOWN ACTUAL SIZE
3
M5 Lock Nut - 2
Assembly
IMPORTANT! Before assembly, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel
for replacement parts and instructions if needed. Never
substitute parts.
Button
Holes Up
Lower Leg
Foot
1
• Position a lower leg so that it stands on a flat surface, as shown.
• Fit a foot onto the end of the lower leg.
• Insert a #8 x 1,3 cm screw through the bottom of the foot
and into the lower leg. Fully tighten the screw with the
Allen wrench.
• Repeat this procedure to assemble the other foot to the
other lower leg.
Red Dot Up
Upper Leg
Upper Legs
3
• Position the fabric panel with the button holes up.
• Position the legs so that the feet are away from you.
• Slide the fabric panel onto the upper legs.
Rivet Through
Button Hole
Button Hole
Straight
End
Button
Hole
Lower Leg
2
• Position an upper leg so that the red dot is up.
• While pressing the button on the straight end of an upper leg,
insert the upper leg into a lower leg. Make sure the button on
the upper leg “snaps” into the hole in the lower leg.
• Repeat this procedure to assemble the other upper leg to the
other lower leg.
4
• Fit the rivets on the upper legs through the button holes
in top ends of the fabric panel.
4
Loading...