Fisher-Price H5988 User Manual
1
Product features and decorations may vary from picture above.
Instructions
Model Number: H5988
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires four LR20 (“D”) alkaline batteries (not included) for swing operation.
Requires four LR6 (“AA”) alkaline batteries (not included ) for toybar operation.
Only to be used by children that cannot climb out of seat.
WARNING
IMPORTANT! PLEASE KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
www.fisher-price.com
2
2
WARNING
To prevent serious injury or death
from falls and being strangled in
the restraint system:
• Always use the restraint system.
Never rely on the tray to restrain child.
• Never use with an active child who may
be able to climb out of the seat.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg (20 lbs).
• Never leave the child unattended.
• It is dangerous to use this product
on an elevated surface.
#8 x 1.9 cm Screw – 3
All Shown Actual Size
Note: Tighten or loosen all screws with a
Phillips screwdriver. Do not over-tighten.
Parts
Oval End Seat Tube
Pad
Toy Bar
Round End
Seat Tube
Seat Back Wire
Motor
Housing
Housing
Tray
Rod
Seat Back
2 Legs
Front
Curved
Base
Seat Bottom
Assembly Tool
(This tool is not a toy. Please
throw away after assembly is complete.)
Back Base
IMPORTANT! Please remove all parts from the package and
identify them before assembly. Some parts may be packed
in the pad.
Lock Nut – 2
3.8 cm Pin Screw – 2
#6 x 3.18 cm Screw – 2
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts.
3
3
1
Button
Leg
Housing
• Place a housing on a flat surface.
• Insert the button end of a leg into the hole in the housing.
• Push the leg in until it “snaps” into the housing.
• Repeat this procedure to assemble the other leg to the
other housing.
• Pull the legs to be sure they are secure in the housings.
If you can remove them, you have not assembled them
correctly. Please re-read and repeat this assembly step.
• Pull the other leg back until it “snaps” into place in the housing.
• Repeat this procedure to “snap” the leg in the other housing
into place.
• Place the front curved base on a flat surface so that it curves
away from you.
• Place the back base on a flat surface, behind the front
curved base.
• Position the leg assemblies so that the hubs are facing
each other.
• Fit the ends of the legs over the ends of the front and back
bases, as shown.
Hint: You may need the help of another adult to help you balance
the assembly.
3
Front Curved Base
Hubs
2
Back Base
Assembly
Leg
4
4
HUBS FACING OUT
FRONT
BASE
CURVES
INWARD
HUBS FACING IN
• Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above.
• If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and repeat
assembly step 3.
• Set the frame assembly aside.
CORRECT INCORRECT
FRONT
BASE
CURVES
OUT
Assembly
5
5
5
• Align the hole in the seat tube with the hole in the armrest.
• Insert a 3.8 cm pin screw through the armrest and into the
seat tube. Tighten the screw.
6
Seat Bottom
Round End
Seat Tube
Armrest Holes
• Position the seat bottom so that the back faces you and the
armrest holes are facing up.
• Locate the round end seat tube.
Hint: Look at opening in the straight end of the tube. It should be round.
• Fit the round end seat tube into the round hole in the
seat bottom.
Round
SIDE VIEW
3.8 cm Pin Screw
3.8 cm Pin Screw
Assembly
7
Oval End
Seat Tube
Seat Bottom
8
• Locate the oval end seat tube.
Hint: Look at opening in the straight end of the tube. It should be oval.
• Fit the oval end seat tube into the oval opening in the
seat bottom.
• Align the hole in the seat tube with the hole in the armrest.
• Insert a 3.8 cm pin screw through the armrest and into the
seat tube. Tighten the screw.
Oval
SIDE VIEW
Loading...