Page 1
GlGlow
www.fisher-price.com
Instructions
Model Number H5791
™
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four “AA” (LR6) alkaline batteries (not included).
Adult assembly is required for battery installation.
Tool required for battery installation:
Phillips screwdriver (not included).
Page 2
Battery Compartment Door
• Locate the battery compartment on
the back of the toy.
• Loosen the screws in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
• Insert four “AA” (LR6) alkaline
batteries, as indicated inside the
battery compartment.
Hint: We recommend using alkaline
batteries for longer life.
• Replace the battery compartment door
and tighten the screws with a Phillips
screwdriver. Do not over-tighten.
• When lights become faint or stop,
it’s time for an adult to change
the batteries!
1.5V x 4
"AA" (LR6)
Battery
Installation
Shown Actual Size
+
Batteries may leak fluids that can cause
a chemical burn injury or ruin your toy.
To avoid battery leakage:
• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the toy. Dispose of
batteries safely. Do not dispose of
batteries in a fire. The batteries may
explode or leak.
• Never short-circuit the battery
terminals.
• Use only batteries of the same or
equivalent type, as recommended.
• Do not charge non-rechargeable
batteries.
• Remove rechargeable batteries from
the toy before charging.
• If removable, rechargeable batteries
are used, they are only to be charged
under adult supervision.
Battery Safety
Information
Page 3
1 2
Let’s Draw!
• Slide a tracing template or any image
you wish to trace, into the slot in the
back of the toy.
• Use one of the glow makers included
to trace the design or create a design
of your own without the template!
Hints:
• Draw thin lines to create a
"neon" effect.
• Be sure to let markings dry at least
15 seconds before touching.
• As you work, store extra markers
upright in the holes in the drawer.
BACK VIEW
Page 4
• Locate the mode switch near the top
of the toy.
• The switch has three positions: off ;
blink and glow .
• Set the switch to glow to light up
your creation!
• Set the switch to blink to create
an attention grabbing sign! Your
image flashes on and off!
MODE SWITCH
Light it Up! Erasing
• Dampen the eraser with water. Wipe
the drawing surface with the eraser.
IMPORTANT!
• To completely remove glow marker
residue from the drawing surface,
wipe it with a damp cloth after
each use.
• Use only Doodle Pro™Glow markers.
Not all markers are made especially
for children. Fisher-Price®markers
are safe and non-toxic but may stain
some porous surfaces such as
clothing, carpet and furniture. Do
not use permanent markers on the
drawing surface. Adult supervision
is recommended.
• To remove marker from the skin,
simply use soap and water.
3
Page 5
Storage
• Slide the mode switch to the
off position.
• Snap the markers into the storage
slots on the back of the toy.
Hint: Be sure to replace the caps
tightly on the markers to prevent
them from drying out.
• Store your tracing templates in the
slot on the back of the toy.
• Wipe this toy with a clean,
damp cloth.
• This toy has no consumer
serviceable parts. Do not take
this toy apart.
• Do not apply heavy pressure or
force to the drawing screen.
Care
FCC Note
(United States Only)
Note: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not
installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which
can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modifications not
expressly approved by the manufacturer responsible for compliance could
void the user’s authority to operate
the equipment.
Page 6
Look for Doodle Pro
™
Glow Accessory Packs
Learning Basics
Dinosaurs
Underwater
™
Zoo Animals
Barbie
®
More glow markers in more glow
colors, plus fun tracing templates!
Hot Wheels
®
Consumer
Information
Questions? We'd like to hear from you!
Call Fisher-Price®Consumer Relations,
toll-free at 1-800-432-5437, 8 AM 6 PM EST Monday through Friday.
Hearing-impaired consumers using
TTY/TDD equipment, please call
1-800-382-7470. Or, visit us on line at
www.service.mattel.com.
Write to us at: Fisher-Price®Consumer
Relations, 636 Girard Avenue,
East Aurora, New York 14052.
For countries outside the United States:
CANADA: Questions? 1-800-432-5437. Mattel Canada
Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R
3W2; www.service.mattel.com.
GREAT BRITAIN: Mattel UK Ltd,
Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500302.
AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church
Street, Locked Bag #870, Richmond, Victoria 3121
Australia. Consumer Advisory Service 1300 135 312.
NEW ZEALAND: 16-18 William Pickering Drive,
Albany 1331, Auckland.
ASIA: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui,
HK, China.
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. PRINTED IN CHINA
©2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. H5791pr-0920
Loading...