Fisher-Price H4790 User Manual
1
Instructions
Model Number: H4790
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Product features and decorations may vary from photo above.
www.fisher-price.com
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.
WARNING
This product contains small parts in its unassembled state.
Adult assembly is required.
Prevent serious injury or death from falls or sliding out:
• The child should at all times wear a safety harness correctly fitted and adjusted.
The tray is not designed to hold the child in the chair.
• Always keep child in view while in the high chair.
• Never leave child unattended.
• It is recommended that the high chair be used in the upright position only by
children capable of sitting upright unassisted.
2
2
CAUTION
Warning and Caution
3
3
Parts
Pad
3 Food Trays
2 Toys
(Toys may be different)
Seat Back
Seat Bottom
Frame
Hinge Rod
2 Seat Bottom Tubes
4 Screw Retainers
Base Tray
Frame
Footrest
Headrest
Basket
Storage Caddy
Front Base
Back Base
#10 x 2.2 cm
Black Screw
#10 x 2.2 cm
Black Screw
#10 x 2.2 cm Black Screw - 7
Shown Actual Size
#8 x 1.9 cm Screw - 8
Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
#8 x 1.9 cm Screws
#8 x 1.9 cm Screws
#10 x 2.2 cm
Black Screw
4
2
• Slide a seat bottom tube through each set of plastic rings on
the seat bottom.
1
• Place the seat bottom face down on a flat surface.
• At an angle, fit the footrest on the seat bottom, as shown.
Assembly
Plastic Rings
Footrest
Seat Bottom
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts.
Seat Bottom Tubes
Plastic Rings
3
Seat Bottom Tubes
Plastic Rings
Plastic Rings
#8 x 1.9 cm Screw - 4
• Align the holes in the plastic rings and the seat bottom tubes.
• Insert a #8 x 1.9 cm screw through each plastic ring and into
the seat bottom tubes, as shown. Tighten the screws.
• Push the seat bottom tubes back and forth to be sure they are
secured to the seat bottom. If the seat bottom tubes move, you
have probably not fastened them properly. Remove the screws
and check to be sure the screw holes in the seat bottom tubes
and seat bottom plastic rings are aligned. Replace and tighten
the screws.
5
5
Assembly
4
Insert Screws Here
Footrest
• Insert two #10 x 2.2 cm black screws through the footrest and
into the seat bottom. Tighten the screws.
#10 x 2.2 cm Black Screw - 2
5
• Turn the seat bottom assembly upright.
• Fit the seat back pins into the openings in the top side of the
seat bottom assembly.
Seat Back Pin
Opening
Seat Bottom Assembly
Opening
Seat Back Pin
6
Hinge Rod
Hinge
• Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back and
seat bottom, as shown.
• Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten
the screw.
• Set the seat assembly aside for Assembly step 9.
#10 x 2.2 cm Black Screw
7
• Pull the frame leg out on each frame to open. Make sure it
"clicks" into place.
Frame Leg
Loading...