Fisher-Price H4788 User Manual

1

1

Instructions

Model Number: H4788

Please read these instructions before assembly and use of this product.

Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).

Requires four “D” (LR20) alkaline batteries (not included) for operation.

Product features and decorations may vary from picture above.

www.fisher-price.com

WARNING

IMPORTANT! KEEP FOR FUTURE REFERENCE.

WARNING

Parts

IMPORTANT! Please remove all parts from the package
and identify them before assembly. Some parts may be
packed in the pad.

2 Toys

#8 x 2.22 cm Screw – 2

All Shown Actual Size

Note: Tighten or loosen all screws with a Phillips

screwdriver. Do not over-tighten.

#6 x 2.86 cm

Red Shoulder Screw – 2

M5 x 20 mm Screw - 2

To prevent serious injury or death:

•It is dangerous to use this reclined
cradle on an elevated surface, since
child's movement may cause infant
seat to slide or tip over.

•Never use on a soft surface (bed,
sofa, cushion), since seat can tip over
and cause suffocation in soft surfaces.

•Always use the restraint system.

•Never leave the child unattended.

•Never use as a car seat.

•Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg (20 lbs).

•To prevent the massaging rollers from
contacting baby’s head, use only for a
baby weighing at least 2.3 kg (5 lbs).

CAUTION

This package contains small parts

in its unassembled state.

Adult assembly is required.

2 Feet

Left Base Wire

Liner

Right Base Wire

Base Tube

Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New Yor k 14052, U.S.A.

©2004 Mattel, Inc. All Rights Reserved.

® and ™ designate U.S. trademarks of Mattel, Inc.

PRINTED IN CHINA H4788pr-0726

Pad

GREAT BRITAIN

Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500302.

AUSTRALIA

Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia. Consumer Advisory Service
1300 135 312.

ASIA

Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.

MALAYSIA

Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P)
Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf
Country Resort, 47410 PJ. Tel: [phone], Fax: [phone].

Consumer Information

1

2

Assembly

Right Base Wire

Feet Holes

Footrest Wire

Base Tube Holes

•Position the feet so the holes are toward you and the non-skid
surface is down.

•Fit the feet on the base tube, as shown.

IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Mattel for replacement parts and instructions if needed. Never
substitute parts.

•Place the base tube on a flat surface, with the holes facing you.

•Position the left and right base wires as shown.

•Fit the left base wire and right base wire into the base tube.

Left Base Wire

3

3

•Insert an M5 x 20 mm screw through each foot and tighten.

M5 x 20 mm Screw - 2

4

•Place the liner on a flat surface with the soother unit facing you.

•Lift the footrest wire and rotate it toward you until it is on
the surface.

•Turn the liner over so that the soother is upright.

Liner

Soother Unit

Soother Unit