Fisher-Price GWT23 User Manual

UNITED STATES

Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Consumer Services: 1-800-432-5437.

CANADA

Mattel Canada Inc., 6155 Freemont Blvd., Mississauga,
Ontario L5R 3W2 Consumer Services/Service à la clientèle :
1-800-432-5437. www.service.mattel.com.

GREAT BRITAIN

Mattel U.K. Limited, The Porter Building, 1 Brunel Way, Slough SL1 1FQ, UK.
www.service.mattel.com/uk.

NEDERLAND

Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.

AUSTRALIA

Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.

NEW ZEALAND

16-18 William Pickering Drive, Albany 1331, Auckland.

SOUTH AFRICA

Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard,
Johannesburg 2196.

FCC STATEMENT (UNITED STATES ONLY)

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.

Keep these instructions for future reference as they

contain important information.

Requires three AA batteries (included).

Batteries included are for demonstration purposes only.

Adult assembly and battery replacement is required.

Tool required: Philips screwdriver (not included).

To clean, wipe with a damp cloth. Do not immerse.

DC SUPER FRIENDS and all related characters and
elements © & ™ DC Comics.
WB SHIELD: TM & © WBEI.
(s20)

©2020 Mattel. ® and ™ designate U.S. trademarks of Mattel, except as noted.

PRINTED IN CHINA 1102684248-DOM

GWT23-0970

1

Remark:

Revision Date ID# Changes

Primary - pr 12/25/2020 GWT23-0970-1102684248-DOM NA

GWT23

BATTERY INSTALLATION AND POWER ASSEMBLY

p

1,5V x 3

AA (LR6)

For longer life, use alkaline batteries.

Slide the power
switch to ON or
OFF .

Battery Safety Information

In exceptional circumstances, batteries
may leak fluids that can cause a chemical
burn injury or ruin your product. To avoid
battery leakage:

• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable.

• Insert batteries as indicated inside the
battery compartment (+ and -).

• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the product. Dispose of
batteries safely. Do not dispose of this
product in a fire. The batteries inside
may explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or
equivalent type, as recommended.

• Do not charge non-rechargeable
batteries.

• Remove rechargeable batteries from
the product before charging.

• If removable, rechargeable batteries
are used, they are only to be charged
under adult supervision.

M3,5 x 15 mm Screw

Tighten or loosen the screws with a Phillips

screwdriver. Do not over-tighten the screws.

1 2

x4

the screws.

• Turn the Power Pad to lower the toy
into flight mode. Locate the battery
compartment door on the back of
the toy.

• Loosen the screw in the battery
compartment door with a Phillips
screwdriver and remove the door.

• Remove the exhausted batteries and
properly dispose.

• Insert three, new AA (LR6)
alkaline batteries.

• Replace the battery compartment
door and tighten the screw. Do not
over-tighten.

• If this toy begins to operate erratically,
you may need to reset the electronics.
Slide the power switch off and then
back on again.

Protect the environment by not
disposing of this product or any
batteries with household waste.
This symbol indicates that this
product shall not be treated as
household waste. Check your
local authority for recycling
advice and facilities.

CAN ICES-3 (B)/NMB-3 (B)

Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.

L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes : (1)
il ne doit pas produire de brouillage et
(2) il doit pouvoir tolérer tout brouillage
radioélectrique reçu, même si ce brouillage
est susceptible de compromettre son
fonctionnement.

2 3

3