Fisher-Price G4815 User Manual
G4815
Instructions
Bounce ‘n Go
™
Coupe
Please read these instructions carefully and identify all parts before assembly.
Refer to the parts and fasteners pages for identification.
Keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Ages 18 months – 5 years.
Maximum weight: 50 lbs. (23 kg).
Tools needed for assembly: Hammer, Phillips Screwdriver and Scrap Block of Wood (not included).
This product requires three “AAA” (LR03) alkaline batteries (not included) for sound box operation.
If you have any questions about this product, or are missing a part, please contact Fisher-Price
®
(online at www.service.mattel.com or call toll-free at 1-800-432-5437) rather than return this product to the store.
www.fisher-price.com
Stationary
Bouncy-Car Action
1
2
Push’n Pedal Car
3
Pedal Car
2
Parts
Handle/Canopy
Notes:
• Some parts shown are assembled to
both sides of the coupe.
• Please save all packaging material until
assembly is complete to ensure that no
parts are discarded.
• Please wipe each part with a clean, dry
cloth before assembling this product.
• Part not shown: label sheet.
Upper Post
Sound Box Cover
Sound Box
.354" Cap Nut
Steering Wheel
Turn Signal
Steering Wheel Base
2 Axle Covers
2 .354" Cap Nuts
Frame
Latch Halves
Grip Halves
Seat
Lower Post
Rear Axle
Footrest
Steering
Column
Steering Linkage Assembly - Fitted to Frame
(with Front Axles)
2 5/16" Washers
2 Frame Bushings
2 Small Front Wheels
4 Wheel
Bushings
4 – .354"
Cap Nuts
Assembly Tool
Bouncing Base/Spoiler
4 Axle Bushings
4 Axle
Covers
2 Large Rear Wheels
3
Warning and Caution
CAUTION
WARNING
To avoid serious injury:
• Adult supervision required.
• Never use near cars and other motor vehicles, near streets, steps, sloped driveways,
hills, roadways, alleys, swimming pools, or
other bodies of water.
• Always wear shoes or sneakers
• Never allow more than one (1) rider.
#10 x 21/8" Bolt – 1
ALL SHOWN ACTUAL SIZE
5
/16" Washer - 2
.354" Cap Nut - 7
#6 x
1
/2" Screw – 6
1
/4" x 11/4" Screw – 1
#8 x
3
/4" Screw – 11
.354"
Note: Tighten and loosen all screws and the bolt with a
Phillips screwdriver. Do not over-tighten the screws and bolt.
This product contains small parts in its
unassembled state.
Adult assembly is required.
Fasteners
Note: We’ve included extra fasteners for your convenience!
4
1
• Place the frame upside down on a flat surface. Make sure the steering
linkage assembly is fitted to the front end of the frame.
• Remove the tape holding the front axles to the frame. Rotate the front
axles out.
2
• Push the front axles down into the groove in each end of the
steering linkage.
3
• Fit the peg on the footrest into the hole inside the frame.
• Insert the 1/4" x 11/4" screw into the footrest and tighten.
PUSH
Assembly
Steering Linkage
Assembly
Frame
Front Axles
Groove
Groove
PUSH
Footrest Peg
4
• While holding the steering linkage assembly in place, carefully turn
the frame upright.
• Fit a .354" cap nut onto the upright end of a front axle.
• While holding the front axle in place, tap the cap nut with a hammer
to secure it to the front axle. Pull up on the cap nut to be sure it
is secure.
Hint: You may need the help of another adult to hold the front axle
in place while you tap the cap nut with a hammer.
• Repeat this procedure to assemble another cap nut to the other
front axle.
.354"
Cap Nuts
Front Axles
Bottom View
Front Side View
.354"
5
5
• Fit an axle cover over the cap nuts and to the front end of the frame.
Push down on the axle covers to “snap” them into place.
Hint: You may need to carefully tap the axle covers with a hammer
to secure in place.
Axle Covers
6
• Slide a 5/16" washer onto a front axle.
• Next, fit an axle bushing, barrel side first, onto a front axle.
7
• Locate both small, front wheels.
• Slide a small, front wheel, flat side first, onto the front axle.
Assembly
5
/16" Washer
Axle
Bushing
Front Axle
Small
Front Wheel
8
• Fit a wheel bushing, peg side first, into the small, front wheel and onto
the front axle.
Wheel
Bushing
Loading...