GAUNTLET
WARNING: Do not aim at eyes or face. Only use
projectiles supplied with this toy.
Do not fire at point blank range.
Always wear appropriate eye-wear,
sold separately.
INSTRUCTIONS
Please keep these instructions for future reference as they contain important information.
CONTENTS
1
SHIELDS
2
A. Activate shields.
CAUTION: Do not aim at eyes or face.
TO AVOID INJURY: Use only darts
designed for this product.
Do not modify rounds, darts, or dart blaster.
Pull rounds apart and stick
them back together!
x 30
B. To close shields.
Detach shields as desired.
a
Click!
b
1
GAUNTLET
TO FIRE
3
A. Fully load clip with darts.
Pump sliding handle all the way forward and all the
C.
way back up to 18 times for maximum fire power.
18x
B. Insert the fully loaded clip from the left
side of the blaster with the arrowheads
pointing right.
a
b
Click!
Align to blaster
as shown.
TOP VIEW
D.
Pull trigger and release
quickly for single fire.
OR
2
Pull and hold trigger for rapid fire.
GAUNTLET
RESET BUTTON
RESET
4
A.
Remove empty clip from blaster. B. Press and hold RESET button and
trigger to release all air from blaster.
IMPORTANT:
Release all air from
blaster when not in use.
IMPORTANT INFORMATION
PERFORMANCE TIPS
5
If rapid fire suddenly stops, try doing the following:
Check if there are empty slots in the clip. Press and release RESET button and pull trigger to advance
1.
clip one slot. At last empty slot, press and release RESET button and pull trigger to fire blaster.
IMPORTANT INFORMATION
Read Carefully!
Read Carefully!
2.
a
Pump sliding handle again to restore air
pressure as needed to fire remaining darts.
b
3.
Clip may stop or slow down when dirt and lint
gather in clip rails and blaster channels. For
best performance, periodically wipe surfaces
clean with paper towel (not included).
3
GAUNTLET
ATTACHING TARGETS
6
REMOVING DARTS
7
& ROUNDS
Peel backing off target before sticking it to surface.
Do not stick target to walls or furniture as
✖
it may cause damage to the surface.
CLEANING DARTS
8
& ROUNDS
Dust, dirt, and other debris can cause darts and
rounds to lose their adhesiveness.
To clean them, rinse darts’ tips and rounds with
tap water or use tape to remove excess debris.
NOTE: Dry darts and rounds before using again.
IMPORTANT:
Always remove darts and rounds from target
after play. Keep one hand pressed on target,
gently peel round off or hold dart by the tip
and peel off.
REPLACING TARGETS
9
& SHIELDS
Y8620/BBY17
Replace time-worn targets and shields with
Y8620/BBY17 SMART STICK REFILLS.
Each sold separately, subject to availability.
CGN78-0920
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations
1-800-524-8697. Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty.,
Ltd., Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th
Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia. Tel:03-78803817, Fax:03-78803867.
4
Loading...