Fisher-Price CFG28, CJF95 Instruction Sheet

PILOT'S MANUAL

TM

8+

OUTDOOR USE RECOMMENDED.
ADULT ASSEMBLY REQUIRED.

Keep these instructions for future reference as they contain important information.

IMPORTANT: Please read all instructions before operating your vehicle.

CAUTION:

Surfaces may become hot and cause burns if electronics get wet.

Adult supervision is recommended when the vehicle is being operated.

1

CFG28-0920G1
CFG29-0920G1

Asst.BGK77

service.mattel.com

Coin

CONTENTS

FEATURES

L

R

1

4

2

7

8

5

3

6

ABOUT THE TRANSMITTER

1

THROTTLE JOYSTICK – Controls both motors and is used
to make the vehicle move forward / ascend / descend.

2

STEERING JOYSTICK – Controls the left and right motors
independently to make the vehicle turn left / right.

3

ALIGNMENT ADJUSTMENT BUTTONS – Use to correct
the direction of the vehicle if it veers to either side.

4

TRANSMITTER POWER SWITCH

• Select ( ) to charge the vehicle.

• Select ( ) to switch transmitter OFF.

• Select ( ) to switch transmitter ON.

5

GROUND ( ) / FLIGHT ( ) MODE SWITCH – Use to
select between Ground Mode and Flight Mode.

6

POWER CABLE SOCKET – Use to charge the vehicle with
the USB cable (included).

SAFETY INFORMATION
Note to Adults: To ensure that the child’s play is both safe and fun, please review all operating instructions and

safety rules with your child.

• The toy is not intended for children under 8 years old.

• Keep fingers, hair and loose clothing away from the propellers while the vehicle is switched ON.

• Stay at least 3 to 6 feet away from the vehicle. That goes for anyone watching as well.

•

Always keep an eye on the vehicle. If it looks like it’s going to crash into you, your friends or anything else, release the throttle joystick and step out of the way.

• Never disassemble or attempt to modify the vehicle.

• When not in use, turn off vehicle and then transmitter. To avoid accidental operation, remove batteries in transmitter.

• Operating range of transmitter is 200 ft. (60m).

ABOUT THE VEHICLE

7

VEHICLE POWER SWITCH

• Select ( ) to switch vehicle OFF.

• Select ( ) to switch vehicle ON.

8

CHARGING SOCKET – Use to charge the vehicle’s internal LiPo
battery.

STREET HAWK™ HAS A SPECIALLY-DESIGNED
DURAFORM™ BODY COMPRISED OF EXPANDED
POLYPROPYLENE (EPP), MAKING IT LIGHTWEIGHT AND
EXTREMELY RESILIENT FOR LONG-TERM DURABILITY.

Coin

SET UP

1. TRANSMITTER BATTERY INSTALLATION

1.

Unscrew the battery cover with a Phillips head screwdriver (not included).

2. Install 6 AA (LR6) alkaline batteries (not included) with polarity (+/-) as
shown inside the battery compartment.

3. Replace battery cover and tighten screws.
Replace batteries in the transmitter if the vehicle runs slowly after a recharge

4.

or if you see a green light flashing in the transmitter power switch.

2. CHARGING THE VEHICLE

MUST CHARGE VEHICLE BEFORE FIRST USE. CHARGE TIME IS APPROXIMATELY 40 MINUTES OR MORE.

Your vehicle is powered by a LiPo battery that is permanently installed. The vehicle must be charged before play. It can be charged with the transmitter
or with the USB cable.

CHARGING WITH THE TRANSMITTER

1. To charge, first make sure you have installed 6 AA alkaline batteries in the transmitter and that both the transmitter and vehicle are
switched OFF ( ).

2.

Open the cover on the transmitter and take out the charging cable

3. Insert the charging plug firmly into the socket under the vehicle. Make sure the connection is secure (see ).

4. To begin charging, move the transmitter power switch from OFF ( ) to CHARGE ( ). A red light in the power switch will turn on. This indicates the
vehicle is charging. (see ).

5. The charging process takes approximately 40 minutes or more. The red light will go off when charging is complete.

6. Hold the charging plug and gently pull it out of the socket. NEVER pull on the cable as this may cause the cable to break.

7. Replace the charging cable into the transmitter and close the cover.

8. The vehicle will usually have about 5-6 minutes of flight time once fully charged.

c

(see ).

a

b

a

b

CHARGING WITH THE USB CABLE

1. Connect the transmitter to a powered USB port with the supplied USB cable.

2. Follow the same instructions as detailed in CHARGING WITH THE

TRANSMITTER.

3. Remember to disconnect the USB cable from the transmitter before play.

c

32