Fisher-Price BMM01 Instruction Sheet

K3799

• Please keep this instruction sheet for future reference,
as it contains important information.

• Requires three "D" (LR20) alkaline batteries for the
mobile and two "AA" (LR6) alkaline batteries for the
remote (batteries not included).

• Adult assembly required.

• Tool required for assembly: Phillips screwdriver
(not included).

Consumer Information

WARNING

Prevent Entanglement Injury

• Keep mobile out of baby's reach

• Remove mobile portion of product from crib or playpen when baby
begins to push up on hands and knees.

• This product may not attach to all crib designs. Do not add additional
strings or straps to attach to crib or playpen.

• Use ONLY attached to a crib or playpen.

IMPORTANT! Always attach with all provided fasteners tightly to a crib or
playpen according to the instructions. Do not add additional strings or straps
to attach to a crib. Check frequently. The mobile portion of this product may be
used from birth until 5 months. The base portion of this product may be used
from birth until 24 months. A crib mobile is intended for visual stimulation and
is not to be grasped by a child.

Care

• Wipe this toy with a clean cloth dampened with a mild soap and water solution.
Do not immerse this toy.

• This toy has no consumer serviceable parts. Do not take this toy apart.

• Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities.

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can cause a chemical
burn injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.

• Remove batteries during long periods of non-use. Always remove exhausted
batteries from the product. Dispose of batteries safely. Do not dispose of this
product in a fire. The batteries inside may explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the product before charging.

• If removable, rechargeable batteries are used, they are only to be charged
under adult supervision.

2

Parts

Base

Clamp

Remote

Crib
Adaptor

3 Soft Toys

Arm

Mobile Hub

3 Leaves

Note: All of the screws used to assemble this toy are attached to the product.

Follow these instructions carefully to fully secure the screws.

Tighten and loosen all screws with a Phillips screwdriver. Do not overtighten.

3

Battery Installation

Hint: We recommend using alkaline batteries for longer battery life.

1,5V x 3

“D” (LR20)

1,5V x 2

“AA” (LR6)

Mobile Base Remote

• Loosen the screws in mobile base battery compartment door with Phillips

screwdriver and remove the door.

Hint: If the crib adaptor is attached to the base, loosen the screws in the crib
adaptor and remove it first.

• Insert three "D" (LR20) alkaline batteries.

• Loosen the screw in the remote battery compartment door with a Phillips

screwdriver and remove the door.

• Insert two "AA" (LR6) alkaline batteries.

• Replace each battery compartment door and tighten the screws.

IMPORTANT! Under normal use conditions, the batteries in the base will require
replacement more often than the batteries in the remote. When sounds or light
become faint or movement of the mobile is sluggish, it's time for an adult to
replace the batteries in the base.

IMPORTANT! If the mobile does not respond to the remote, it does not mean that
the battery power in the remote is low. Replace the batteries in the remote if the
LED signal indicator on the remote is dim when the button is pressed. If the LED
signal indicator does not light after installing new batteries in the remote, check
the orientation of the batteries in the battery compartment to make sure they are
properly installed.

©2012 Mattel. All Rights Reserved.

PRINTED IN CHINA K3799b-0920

4

Assembly

Base

Crib Adaptor

1

• Fit the crib adaptor to the base.

• Tighten the four screws in the crib adaptor.

 PRESS

SLIDE



Arm

Socket

Base

2

• First press the button next to the socket  and then slide the socket
door open .

• Fit the arm into the socket in the base.

• Tighten both screws in the arm.

5

Assembly

Mobile Hub

3

• Fit the mobile hub onto the end of the arm.

• Tighten both screws in the arm to secure the mobile hub.

Hint: You may want to attach the soft toys to the mobile hub before assembling
the arm to the mobile hub. Please refer to assembly step 5 for instructions to
assemble the soft toys.

6

Assembly

4

• “Snap” the leaves into the slots in the mobile hub.

5

• Fit the soft toys to the pegs on the underside of the mobile hub.

• Tighten the screw in each toy to secure each to the mobile hub.

Soft Toys

Leaves

7

Crib Attachment

Base

Crib Top Rail

• Fit the base onto the crib top rail, so that the threaded peg extends

outside the crib.

• Fit the clamp onto the threaded peg and turn the clamp clockwise to

secure the base to the crib.

• Do not over-tighten the clamp.

Clamp

Mattress

At least 7 inches

Bottom of Base

• If the distance between the bottom of the base and the mattress is less than

7 inches (18 cm), lower the crib mattress.

8

Remote Use

• Press the button on the remote to activate music, lights and motion.

• Press again to stop.

• In the unlikely event that use of the remote interferes with normal use

of other remote controlled equiment, such as televisions or stereos, or use of
other electronic or battery powered appliances interfere with operation of the
mobile, do not use both at the same time.

• You may notice a loss of range between the remote and the mobile when using

in bright light. For best performance, avoid using the remote in areas of bright
light. Move the mobile, or reduce the amount of light to improve performance.

• Position the mobile so that the receiver arrow points towards the area that the

remote will be used. Make sure there is a clear path between the remote and
the mobile. Point the end of the remote toward the mobile receiver and
press the button.

Note: The remote will remain active for about one hour. When the LED goes out,
you will need to slide the power/volume switch on the mobile off, then on again
to reactivate.

9

Classical Music, Rainforest Sounds,

Power/Volume Switch

Lights and M

otion Select Switch

Music and Sound Select Buttons

Lights and Motion

Power/Volume Switch

Choose from three settings:

ON with low volume

ON with higher volume

OFF

Lights and M

Lights and Music

Lights, Music and Motion

Motion and Music

otion Select Switch

Music and Sound Select Buttons

Choose classical music from Bach,
Beethoven and Mozart or soothing
sounds of the Rainforest.

10

Convert to a Cribside Music Box

Base

Arm

Remove the mobile and use as
a music box with a night light!

• Loosen both screws in the arm near
the base.

• Lift and remove the arm with mobile
from the base.

• Close the small door on top of the
base. Store the mobile in a safe
place for future use.

11

CONSU

FCC Statement (United States Only)

This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant
to Part 15 of the FCC Rules. These
limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is
no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:

• Reorient or relocate the receiving
antenna.

• Increase the separation between the
equipment and receiver.

• Consult the dealer or an experienced
radio/TV technician for help.

Note: Changes or modifi cations
not expressly approved by the
manufacturer responsible for
compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
This device may not cause harmful
interference and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.

1-800-432-5437 (US & Canada)
1300 135 312 (Australia)

Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.

Outside the United States:

Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.

Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk

Mattel Europa B.V., Gondel 1, 1186MJ Amstelveen, Nederland.

Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.

New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.

MER ASSISTANCE

ICES-003

This Class B digital apparatus
complies with Canadian ICES-003.
Operation is subject to the following
two conditions: (1) this device may
not cause harmful interference and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.

NMB-003

Cet appareil numérique de la classe
B est conforme à la norme NMB­003 du Canada. L’utilisation de ce
dispositif est autorisée seulement
aux conditions suivantes : (1) il ne
doit pas produire de brouillage et
(2) l’utilisateur du dispositif doit
être prêt à accepter tout brouillage
radioélectrique reçu, même si
ce brouillage est susceptible de
compromettre le fonctionnement
du dispositif.

12