Fisher-Price BMK14 Instruction Sheet

Side-to-side
BMK14
Head-to-toe
IMPORTANT! Please keep these instructions for future reference.
Please read these instructions before assembly and use of this product.
Adult assembly is required.
Requires four D (LR20) alkaline batteries and two AAA (LR03) alkaline batteries for
operation (batteries not included).
Product features and decorations may vary from photographs.
fisher-price.com
1
PRESS
PRESS
Storage & Care
IMPORTANT! Remove the batteries for long-term storage.
PRESS
PRESS
Consumer Information
• Press the buttons on each hub and push the bases together for storage.
• Lean the swing frame against a wall for storage.
• To remove the pad, unbuckle the restraint system and the straps under the seat. Pull to remove the pad.
• Machine wash the pad in cold water with a mild detergent. Do not use bleach. Tumble dry on low heat and remove promptly.
• To clean the frame, restraint system and toys, use a mild cleaning agent and damp cloth. Rinse with clean water to remove residue.
• To replace the pad, follow the assembly instructions.
• Periodically check the swing for loose fasteners or broken parts and tighten as needed.
UNITED STATES 1-800-432-5437. Fisher-Price, Inc.,
636 Girard Avenue, East Aurora, NY 14052. Hearing-impaired consumers: 1-800-382-7470.
©2013 Mattel. All Rights Reserved.
PRINTED IN CHINA BMK14pr-0920
2
Consumer Information
WARNING
Prevent serious injury or death from falls or strangling in the restraint system:
• Never leave child unattended.
• This product is not intended to replace a crib or bassinet for prolonged periods of sleep.
• Always use the restraint system.
• Discontinue use when an active child attempts to climb out.
• Never use on any elevated surface. Use only on a floor.
IMPORTANT! The weight limit for this product is 25 lb (11,3 kg). If your child weighs less than 25 lb (11,3 kg), but is really active and appears to be able to climb out of the swing, immediately discontinue its use. IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
• This product comes with replacement warning labels which you can apply over the factory applied warning label if English is not your primary language. Select the warning label with the appropriate language for you.
• Este producto viene con etiquetas de advertencia en español que puede pegar sobre las etiquetas de fábrica, en caso de que el inglés no sea su idioma primario. Seleccione las etiquetas de advertencia en el idioma de su elección.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.
3
Parts
Please remove all parts from the package and identify them before assembly.
Some parts may be packed in the pad.
2 Hubs
2 Bases
Handle
#8 x ¾" (1,9 cm) Screw - 4 M5 x 31 mm Screw – 4
Seat Pad
Seat Base
Seat Back
Seat Bottom
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
4
Assembly
Hub Arms
1
• Fit the tubes on the hubs into the tubes on the bases.
Hint: When assembled properly, the hub arms should face each other.
Bases
Seat Bottom
Seat Base
2
• Fit the seat bottom onto the seat base.
Hint: The seat bottom is designed to fit onto the seat base one way. If it does not seem to fit, turn it around and try again.
• Insert two #8 x ¾" (1,9 cm) screws into the seat bottom and tighten.
5
Loading...
+ 11 hidden pages