Fisher-Price BLP50 Instruction Sheet

Side-to-side

BLP50

Head-to-toe

IMPORTANT! Please keep these instructions for future reference.

Please read these instructions before assembly and use of this product.

Adult assembly is required.

Tool needed for assembly: Phillips screwdriver (not included).

Requires four D (LR20) alkaline batteries and two AAA (LR03) alkaline batteries for

operation (batteries not included).

Product features and decorations may vary from photographs.

fisher-price.com

1

PRESS

PRESS

Storage & Care

IMPORTANT! Remove the batteries for
long-term storage.

PRESS

PRESS

Consumer Information

• Press the buttons on each hub and push
the bases together for storage.

• Lean the swing frame against a wall
for storage.

• To remove the pad, unbuckle the restraint
system and the straps under the seat. Pull to
remove the pad.

• Machine wash the pad in cold water with
a mild detergent. Do not use bleach. Tumble
dry on low heat and remove promptly.

• To clean the frame, restraint system and
toys, use a mild cleaning agent and damp
cloth. Rinse with clean water to
remove residue.

• To replace the pad, follow the
assembly instructions.

• Periodically check the swing for loose
fasteners or broken parts and tighten
as needed.

UNITED STATES
1-800-432-5437. Fisher-Price, Inc.,

636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers:
1-800-382-7470.

©2013 Mattel. All Rights Reserved.

PRINTED IN CHINA BLP50pr-0920

2

Consumer Information

WARNING

Prevent serious injury or death from falls or strangling in the
restraint system:

• Never leave child unattended.

• This product is not intended to replace a crib or bassinet for prolonged
periods of sleep.

• Always use the restraint system.

• Discontinue use when an active child attempts to climb out.

• Never use on any elevated surface. Use only on a floor.

IMPORTANT! The weight limit for this product is 25 lb (11,3 kg). If your child weighs less
than 25 lb (11,3 kg), but is really active and appears to be able to climb out of the swing,
immediately discontinue its use.
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware,
loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or
broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never
substitute parts.

• This product comes with replacement warning labels which you can apply over the
factory applied warning label if English is not your primary language. Select the warning
label with the appropriate language for you.

• Este producto viene con etiquetas de advertencia en español que puede pegar sobre las
etiquetas de fábrica, en caso de que el inglés no sea su idioma primario. Seleccione las
etiquetas de advertencia en el idioma de su elección.

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.

• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the product before charging.

• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.

3

Parts

Please remove all parts from the package and identify them before assembly.

Some parts may be packed in the pad.

2 Hubs

2 Bases

Handle

#8 x ¾" (1,9 cm) Screw - 4 M5 x 31 mm Screw – 4

Seat Pad

Seat Base

Seat Back

Seat Bottom

Note: Tighten or loosen all screws with a Phillips screwdriver.

Do not over-tighten the screws.

4

Assembly

Hub Arms

1

• Fit the tubes on the hubs into the tubes on the bases.

Hint: When assembled properly, the hub arms should face each other.

Bases

Seat Bottom

Seat Base

2

• Fit the seat bottom onto the seat base.

Hint: The seat bottom is designed to fit onto the seat base one way. If it does not seem to
fit, turn it around and try again.

• Insert two #8 x ¾" (1,9 cm) screws into the seat bottom and tighten.

5

Assembly

Seat Back

3

• Fit the seat back onto the seat base.

Hint: The seat back is designed to fit onto the seat base one way. If it does not seem to fit,
turn it around and try again.

• Insert two #8 x ¾" (1,9 cm) screws into the seat back and tighten.

Hub Arms

4

• Turn the seat assembly sideways.

• Fit the seat assembly tubes up into the sockets in the hub arms.

Hint: The seat assembly is designed to fit one way. If it does not seem to fit, turn it around
and try again.

6

Assembly

5

• Insert an M5 x 31 mm screw into each hub arm and tighten.

Handle

6

• Fit the ends of the handle into the socket in each hub.

• Insert an M5 x 31 mm screw into each hub and tighten.

7

Assembly

LOWEST SLOTS

7

• Insert the waist belts through the lowest slots in the seat pad. Make sure the waist belts
are not twisted.

8

Smaller Baby

• Insert the ends of the shoulder belts through the lower slots in the seat pad back. Make
sure the shoulder belts are not twisted.

Waist Belts

LOWER SLOTS

Shoulder Belts
Lower Slots

8

Assembly

UPPER SLOTS

Shoulder Belts

9

Larger Baby

• Insert the ends of the shoulder belts through the upper slots in the seat pad back. Make
sure the shoulder belts are not twisted.

Upper Slots

10

• Fit the pad edges around the rim of the seat.

9

Assembly

11

• Fasten the buckles on the front of the seat pad to the buckles on the seat bottom. Make
sure you hear a “click”.

10

Battery Installation

1,5V x 4

D (LR20)

Hint: We recommend using

alkaline batteries for longer

battery life.

Hub

• Loosen the screws in the battery compartment door with a Phillips screwdriver and
remove the battery compartment door.

• Insert four D (LR20) alkaline batteries into the battery compartment.

• Replace the battery compartment door and tighten the screws.

• If the swing begins to operate erratically, you may need to reset the electronics. Slide the
power switch off and back on.

Note: Low battery power may cause product movement to slow, sound to become faint
or product to turn off all together. If this should happen, replace the batteries with four

alkaline D (LR20) batteries.

1,5V x 2

AAA (LR03)

Handle

• Loosen the screw in the battery compartment door and remove the door.

• Insert two AAA (LR03) alkaline batteries.

• Replace the battery compartment door and tighten the screws.

• If lights begins to operate erratically, you may need to reset the electronics. Remove the
batteries and reinstall them.

• When lights become faint or stop, it's time for an adult to change the batteries.

• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities.

11

Using the Restraint System

WARNING

Prevent serious injury or death from falls or strangling in the
restraint system:

• Never leave child unattended.

• This product is not intended to replace a crib or bassinet for prolonged
periods of sleep.

• Always use the restraint system.

• Discontinue use when an active child attempts to climb out.

• Never use on any elevated surface. Use only on a floor.

Shoulder Belt Shoulder Belt

Waist Belt

1

• Place your child in the seat. Position the crotch belt between your child’s legs.

• Insert the ends of the waist belts through the slots in the shoulder belts.

• Fasten the waist/shoulder belts to the crotch belt. Make sure you hear a "click" on both

sides.

• Tighten each waist belt so that the restraint system is snug against your child. Please
refer to the next section for instructions to tighten the waist belts.

Crotch Belt

Waist Belt

12

Using the Restraint System

2

• To tighten the waist belts: Feed the anchored end of the belt up through the buckle to
form a loop A. Pull the free end of the belt B. Repeat this procedure to tighten the
other belt.

• To loosen the waist belts: Feed the free end of the belt up through the buckle to form
a loop A. Enlarge the loop by pulling on the end of the loop toward the buckle. Pull the
anchored end of the belt to shorten the free end of the belt. Repeat this procedure to
loosen the other belt B.

3

To tighten the shoulder belts: Hold the adjuster A and pull the front shoulder strap
down B.

To loosen the shoulder belts: Slide the adjuster down.
Note: After adjusting the belts to fit your child, make sure you pull on them to be sure they

are securely fastened.

TIGHTEN

TIGHTEN

LOOSEN

Adjusters

LOOSEN

13

2 Swinging Motions

2 Swingin

Turn the seat for
side-to-side swinging.

• Adjust the seat for side-to-side or head-to-toe swinging. Rotate the seat to the
desired position.

Turn the seat for
head-to-toe swinging.

14

Press

Press

Use

Power Switch

Swing Speed
Buttons

Music/Sounds
Button

Volume Buttons

Swing

• Slide the power switch ON.

• Press the swing speed buttons to select any of six speed settings.

• Swinging will turn off after approximately four hours. Press a swing speed button
to restart.

• Be sure slide the power switch OFF when not in use.

Music and Sounds

• Press the music/sounds button to turn music/sounds ON. Press the button again to
turn music/sounds OFF.

Hint: Music/sounds will turn off after approximately 20 minutes. Press the music/sounds
button to restart.

• Press the volume buttons to adjust the volume level.

Colorful Lights

• Press the button on the handle to start the light show.

Hint: Lights will turn off after approximately 20 minutes. Press the button again

to restart.

15

Consumer Information

FCC Statement (United States Only)

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Note: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause
undesired operation.

ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause
undesired operation.

NMB-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à
accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.

16