Fisher-Price B8866 User Manual
Healthy Care
High Chair
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Model Number: B8866
Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
Product features and decoration may vary from the photo above.
™
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
WARNING
2
Occasionally a consumer may experience a problem with one
of our products. If this should happen, please call us, rather
than return this product to the store. Usually, we can solve the
problem over the telephone or send you replacement parts.
Please call 01628 500303 or write to:
Mattel UK Limited
Mattel H
ouse
Vanwall Business Park
Vanwall Road
Maidenhead, B
erkshire SL6 4UB
This product contains small parts
in its unassembled state.
Adult assembly is required.
Consumer InformationWarnings and Caution
Prevent serious injury or death
from falls or sliding out.
• The child should at all times
wear a safety harness correctly
fitted and adjusted.
• The tray is not designed to hold
the child in the chair.
• Always keep child in view while
in the high chair.
•Never leave child unattended.
• It is recommended that the high
chair be used in the upright
position only by children capable
of sitting upright unassisted.
WARNING
CAUTION
Parts
3
Seat
Bottom
2 Seat Bottom Tubes
Seat Back
Frame
Frame
Footrest
2 Bases
4 Screw Retainers
Hinge
Rod
Base Tray
Food Tray
Pad
#8 x 2 cm (
3
/4") Screws
#8 x 1.9 cm
(
3
/4")
Screws
#8 x 1.9 cm (
3
/4") Screws
#10 x 2.2 cm (
7
/8")
Black Screws
#10 x 2.2 cm (
7
/8")
Black Screw - 4
#10 x 2.2 cm (
7
/8")
Black Screw
Toy
#8 x 1.9 cm (3/4") Screw - 8
SHOWN ACTUAL SIZE
#10 x 2.2 cm (7/8") Black Screw - 7
SHOWN ACTUAL SIZE
Note: Tighten all screws with a Phillips screwdriver. Do not over-tighten the screws.
•Place the seat bottom face down on a flat surface.
•At an angle, fit the footrest on the seat bottom, as shown.
Seat Bottom
Footrest
IMPORTANT! Before assembly,inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing,damaged
or broken. Contact Mattel for replacement parts and
instructions if needed. Never substitute parts.
Assembly
•Slide a seat bottom tube through each set of plastic rings
on the seat bottom.
•Align the holes in the plastic
rings and the seat bottom tubes.
• Insert a #8 x 1.9 cm (3/4") screw
into each plastic ring and tighten.
•Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly.
Remove the screws and check to be sure the screw holes in
the seat bottom tubes and seat bottom plastic rings are
aligned. Replace and tighten the screws.
• Insert two #10 x 2.2 cm (7/8")
black screws through the footrest and into the seat bottom.
•Tighten the screws.
Footrest
Insert Screws
Here
4
Plastic
Rings
Plastic
Rings
Seat Bottom Tubes
Plastic
Rings
Plastic
Rings
Seat
Bottom
Tub es
1
2
4
3
#8 x 1.9 cm (3/
4") Screw- 4
SHOWN ACTUAL SIZE
#10 x 2.2 cm (7/
8")
Black Screw - 2
SHOWN ACTUAL SIZE
•Turn the seat bottom assembly upright.
•Fit the seat back pins into the openings in the top side of
the seat bottom assembly.
Seat
Bottom
Assembly
Seat Back
Pin
Seat Back
Pin
Opening
Opening
Assembly
•Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.
• Insert a #10 x 2.2 cm (7/8") black screw into the hinge rod
and tighten.
•Set the seat assembly aside for Assembly step 10.
•Pull the frame leg out on each frame to open. Make sure it
“clicks” into place.
5
Hinge Rod
Hinge
Frame Leg
5
6
7
#10 x 2.2 cm (7/
8")
Black Screw
SHOWN ACTUAL SIZE
Loading...