Fisher-Price B6463 Instruction Sheet

B6463-0920

U.S.A.

90-DAY LIMITED WARRANTY – TYCO® R/C PRODUCTS

Mattel, Inc. warrants to the original consumer purchaser that this product will be free of defects in material and workmanship for ninety (90) days (unless specified in
alternate warranties) from the date of purchase. Mattel will replace the product in the event of such a defect within the warranty period.

In the event of a defect covered under this warranty, first call the toll-free number listed below. Many problems can be solved in this manner. If necessary, you will be
instructed to return the product, postage prepaid and insured, to the address below. Enclose your name, address, dated sales receipt, and a brief explanation of the
defect. Replacement and return shipment will be free of charge.

This warranty does not cover damage resulting from unauthorized modification, accident, misuse or abuse. If the product is returned without a dated sales receipt the
product may be excluded from coverage under this warranty.

Mattel’s liability for defects in material and workmanship under this warranty shall be limited to replacement, and in no event shall we be responsible for incidental, con­sequential, or contingent damages (except in those states that do not allow this exclusion or limitation). This warranty is exclusive, and is made in lieu of any express or
implied warranty. Valid only in U.S.A. This warranty gives you specific legal rights and you may have other rights, which vary from state to state. Some states do not
allow the exclusion of incidental or consequential damages, so the above exclusions or limitations may not apply to you.

TOLL-FREE NUMBER: 1-888-557-TYCO (8926) (valid only in U.S.A.)
Hours: 8:00 A.M. - 5:00 P.M. Eastern Time; Monday - Friday. Expect some delay in January following the holiday season. Please be patient and keep trying the toll-free number.

ADDRESS FOR RETURNS: CONSUMER RELATIONS, 636 GIRARD AVENUE, EAST AURORA, NY 14052

This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

This device generates and uses radio frequency energy and if
not used properly may cause interference to radio and television
reception. It has been tested and found to comply with the limits
set by the FCC which are designed to provide reasonable protec­tion against such interference.

NOTE: Changes or modifications not expressively approved by
the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.

Keep these instructions for future reference: they contain important information.

©2003 Mattel, Inc., Mt. Laurel, NJ 08054 U.S.A. PRINTED IN CHINA. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.

CAUTION:

Stay clear of the rotor at all times when
operating this vehicle. Contact with spinning rotor may cause
injury or damage, or may damage the rotor.

™

COMPLIANCE WITH FCC REGULATIONS (VALID IN U.S. ONLY)

NOT RECOMMENDED

CAUTION-ELECTRIC TOY:

FOR CHILDREN UNDER
8 YEARS OF AGE. AS WITH ALL ELECTRIC PRODUCTS,PRECAUTIONS SHOULD BE
OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK.
INPUT: 120VAC, 60Hz, 18W. OUTPUT: 15.6VDC, 0.6A, 9.36VA.

SAFETY INFORMATION

Adults, this toy is recommended for chil­dren 10 years of age and older. To ensure
that the child’s play is both safe and fun,
please review the operating instructions
and these general safety rules with the
child.

• Keep fingers, hair and loose clothing

away from the rotor while the vehicle is
switched ON.

• Maintain a minimum 10’/3m distance
between yourself and the vehicle during
operation.

• DO NOT operate the vehicle indoors.

• NEVER hold the vehicle while operating.

•ALWAYSlaunch the vehicle from level

ground.

•NEVER stand under the vehicle during
flight.

• During operation, maintain a minimum
10’/3m distance between the vehicle and
other people or animals.

• Keep small children away from the vehi­cle at all times.

• In the event that the vehicle comes too
close to a person, animal or obstacle during
flight, push the control stick all the way
down to activate the stop feature.

• Adult supervision is recommended AT ALL
TIMES during operation of this toy.

• To avoid accidental operation, remove the

transmitter battery when not in use.

• If the vehicle and/or charger get wet, dis­continue use until they are completely dry.
Thoroughly wipe off all moisture and allow
them to air-dry completely before use.

• DO NOT fly in or near the street! Make
sure you have plenty of open space in all
directions (please read Section VI carefully
before operating).

• DO NOT stand (or allow others to stand)
downwind of the vehicle while flying.

•NEVER operate the vehicle if the rotor
blades are broken or damaged. ALWAYS
make sure the rotor blades are properly
attached and the screws holding them are
fully tightened.

•NEVER operate the vehicle unless it is
fully assembled.

•NEVER throw foreign objects into the path
of the rotor.

INTRODUCTION

Please read this manual thoroughly for
detailed operating instructions and impor­tant safety information.

• The XFO™ vehicle is an advanced-tech­nology vertical-takeoff flying machine with
cool features. It’s easy to fly, challenging to
master…and lots of fun!

• You will need to assemble your vehicle
before use. This is a simple, one-time
process (please see Section II for assembly
instructions). This is an advanced flying
machine! Assembly is a fun “science proj­ect” you get to play with after it’s done.

• This vehicle is powered by a NiMH bat­tery that is permanently installed. The vehi­cle must be fully charged before using.

• The vehicle is recharged with a handy
Field Charger that can be used at your
selected flight location.

• The Field Charger must be charged at a
wall outlet before it can be used to
recharge the vehicle. You will need to
charge the Field Charger for at least 16
hours before use (please see Section III for
details). Once the Field Charger is fully
charged, it will be able to recharge the
vehicle many times. NOTE: you must dis­connect the Field Charger from the vehicle
before operating the vehicle.

I. CONTENTS/FEATURES

1. XFO™ vehicle

(shown fully assembled; please see Section
II for assembly instructions)

q Rotor
w Lightweight body
e ON/OFF switch
r Recharging connector (Field Charger

plugs in here)

t Landing legs (x4)

2. Field Charger

q Vehicle recharge cord (plugs into vehicle)
w Vehicle recharge cord storage (insert

cord into groove as shown)

e CHARGE button
r LED charge indicators (2): red and green

3. Wall Charger

q This end plugs into wall outlet
w This end plugs into Field Charger

l CAUTION: Use only the charger sup­plied with this toy. Do not use any other
charging source.

4. Transmitter

q Joystick flight control (please see

Section V for detailed operation)

w Antenna
e LED indicator
r ON/OFF switch

5. Battery installation – Transmitter

1. To install transmitter battery, unscrew
and open battery cover as shown.
(Screwdriver not included.)

2. Install one 9V battery with polarity (+/-)
as shown inside battery compartment.

3. Replace battery cover and tighten screw.

2

q

w

e

r

t

q

w

e

r

q

w

w

q

e

r

II. VEHICLE ASSEMBLY

Vehicle assembly is a one-time process. It’s
easy and fun…just follow the easy steps
below.

Before you begin: remove all vehicle com­ponents from the package and check them
against this list:

1. Motor/power module

2. Lightweight body panels (x3)

3. Rotor

4. Landing legs (x4)

5. Retaining rings (x2)

6. Self-adhesive nosecone label

STEP-BY-STEP ASSEMBLY

1. The first step is to assemble the vehicle
body panels over the motor/power module.
Begin by locating the body panel with holes
in it (these are for the switch and the
recharging jack).

2. Fit this body panel over the motor/power
module, making sure that the switch and
the recharging connector are accessible
through the body panel holes.

3. Add the remaining 2 body panels as

shown.

4. The body panels are secured by 2 retain­ing rings.

NOTE: the two retaining rings are different
sizes: one has a larger diameter than the
other. Slide the smaller retaining ring over
the nosecone (top) of the vehicle as
shown, fitting it securely into the groove.
Slide the larger retaining ring over the bot­tom of the vehicle as shown, fitting it
securely into the groove.

3