Fisher-Price B1637 User Manual
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Model Number: B1637
PLEASE KEEP FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product, as they contain important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver and Scissors (both not included).
Requires four “D” (LR20) alkaline batteries for swinging and sound operation;
three “AA” (LR6) alkaline batteries for sound ‘n lights tray operation; and
three “AAA” (LR03) alkaline batteries for remote operation (all batteries not included).
Maximum Weight Limit:24 lbs. (10.9 kg).
IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs
less than 24 lbs., but is really active and appears to be able to climb
out of the swing, immediately discontinue its use.
Deluxe Quick Response Swing
with Remote Control
2
Occasionally a consumer may experience a problem with
one of our products. If this should happen, please call us
toll-free, rather than return this product to the store. Usually,
we can solve the problem over the telephone or send you
replacement parts. Please call Fisher-Price® Consumer
Relations, toll-free at 1-800-432-5437,8 AM - 6 PM EST
Monday through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470.
Or,write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
•To prevent serious injury or death
from falls and being strangled in
the restraint system:
- Always use the restraint sys-
tem. Never rely on the tray to
restrain child.
- Never use with an active child
who may be able to climb out of
the seat.
•Never leave child unattended.
WARNING
This product contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
Consumer InformationWa rnings and Caution
Parts
3
Front Base
Rear Base
Housing
2 Rear Legs
(Shorter)
Motor Housing
Seat with Restraint
2 Seat Tubes
Bracket
(with M4 Lock Nuts)
Seat Wire
2 Seat Wire
Caps
2 Accessory Bins
Pad
Sound ‘n
Lights Tray
Mirror Base
Remote Control
and Holder
(with M4 Lock Nut)
Tray
2 Front Legs
(Longer)
M4 Screw - 4
Shown Actual Size
Note: Tighten or loosen all screws and bolt with a Phillips screwdriver.Do not over-tighten the screws.
#8 x 1
3
/8" Screw - 10
Shown Actual Size
#6 x 5/8" Screw - 4
Shown Actual Size
M4 Bolt - 1
Shown Actual Size
•Place the front base on a flat surface.
•Position a front leg (longer) so that the tapered end is
downward, as shown.
•While pressing the button on one of the front legs, insert it
into the front base. Push down on the front leg until the
button “snaps” into the hole in the front base.
•Repeat this procedure to assemble the other front leg to
the front base.
Front Base
Tap er ed End
Tap er ed End
Front Legs
(Longer)
IMPORTANT!
Before assembly, inspect this product for damaged hardware,loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.Never substitute parts.
Assembly
•Using scissors, remove the ribbon connecting the remote
and the holder.
4
Press
Button
Press
Button
Remote
Holder
Ribbon
1
•While standing on the front base, pull the front legs up.
The front legs should remain secured to the front base.
If you can remove the front legs,you have not assembled
them correctly to the front base. Reread and repeat
assembly step 1.
Front Legs
Pull Up
Pull Up
Front Base
2
3
•Position the holder so that the
open end faces forward, as shown.
•Slide the holder onto the front leg with a hole.
Holder
Front
Leg Hole
4
Shown Actual Size
M4 Lock Nut
Rounded
Side
M4 Lock Nut
(Rounded
Side Out)
Hexagonal Opening
Hint: An M4 lock nut has been assembled to the holder at
the factory. During shipment of this product, it may have fallen
out. Check to be sure there is a lock nut in the hexagonal opening
on the holder.If it has fallen out, fit the lock nut back into the
hexagonal opening. Make sure the rounded side of the lock nut
faces out.
Assembly
5
• Position a rear leg so that the tapered end is upright.
•While pressing the button on the top of the rear leg,insert it
into the housing short tube, as shown. Push the rear leg until
the button “snaps” into the hole in the short tube.
•Repeat this procedure to assemble the other rear leg to the
motor housing short tube.
•Pull the rear legs down to be sure they are secure in the
housings. If you can remove them, you have not assembled
them correctly.Please re-read and repeat this assembly step.
Button
Rear Legs
Motor Housing
Short Tube
•Fit the bottom of the remote into the cupped portion of
the holder.
•Push to “snap” the top of the remote under the holder clips.
Holder
6
•Position the holder so that the hole in the holder aligns with
the hole in the front leg.
• Insert the M4 bolt through the holder, front leg and into the
lock nut. Tighten the bolt.
Holder
Front Leg
5
8
Tap er ed
End
• Position the housing so that the hub is inward.
•While pressing the button on the top of a front leg, insert it
into the housing slot, as shown. Push the front leg until the
button “snaps” into the hole in the housing.
•Repeat this procedure to assemble the motor housing to
the other front leg.
•Pull the front legs down to be sure they are secure in the
housings. If you can remove them, you have not assembled
them correctly.Please re-read and repeat this assembly step.
Press
Buttons
Front
Legs
Motor
Housing
Hole
Housing
Hub
Slot
7
Clips
Remote
M4 Bolt
Shown Actual Size
Loading...