Fisher-Price B2105, B0326 User Manual
Model Number: B2105, B0326
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tool needed for assembly:Phillips Screwdriver (not included).
Product features and decoration may vary from the photo above.
Deluxe Healthy Care
High Chair
™
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
2
Occasionally a consumer may experience a problem with one
of our products. If this should happen, please call us toll-free,
rather than return this product to the store. Usually, we can
solve the problem over the telephone or send you replacement parts. Please call Fisher-Price® Consumer Relations,
toll-free at 1-800-432-5437,8 AM - 6 PM EST Monday
through Friday. Hearing-impaired consumers using TTY/TDD
equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
This product contains small parts
in its unassembled state.
Adult assembly is required.
CA UTION
Consumer InformationWarnings and Caution
Prevent serious injury or death
from falls or sliding out.
• The child should be secured in
the high chair at all times by the
restraining system, either in the
recline, semi-recline or upright
position.The restraint belts must
be adjusted to fit your child
snugly. The tray is not designed
to hold the child in the chair.
• Always leave wheels locked.
•Never use near stairs.
• Always keep child in view while
in the high chair.
•Never leave child unattended.
• It is recommended that the high
chair be used in the upright
position only by children capable
of sitting upright unassisted.
WARNING
Parts
3
Seat
Bottom
2 Seat Bottom Tubes
Seat Back
Frame
Frame
Footrest
Back Base
4 Screw Retainers
Front Base
Hinge
Rod
Storage
Caddy
Base Tray
3 Food Trays
Pad
Headrest
#8 x
3
/4" Screws
#8 x
3
/4"
Screws
#8 x
3
/4" Screws
#10 x
7
/8"
Black Screws
#10 x
7
/8"
Black Screw - 4
#10 x
7
/8"
Black Screw
4 Wheels
#8 x 3/4" Screw - 8
SHOWN ACTUAL SIZE
#10 x 7/8" Black Screw - 7
SHOWN ACTUAL SIZE
•Place the seat bottom face down on a flat surface.
•At an angle, fit the footrest on the seat bottom, as shown.
Seat Bottom
Footrest
IMPORTANT! Before assembly,inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions
if needed. Never substitute parts.
Assembly
•Slide a seat bottom tube through each set of plastic rings
on the seat bottom.
•Align the holes in the plastic
rings and the seat bottom tubes.
• Insert a #8 x 3/
4" screw through
each plastic ring and into the
seat bottom tubes, as shown.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
•Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly.
Remove the screws and check to be sure the screw holes in
the seat bottom tubes and seat bottom plastic rings are
aligned. Replace and tighten the screws.
• Insert two #10 x 7/8" black
screws through the footrest
and into the seat bottom.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Footrest
Insert Screws
Here
4
Plastic
Rings
Plastic
Rings
Seat Bottom Tubes
Plastic
Rings
Plastic
Rings
Seat
Bottom
Tub es
1
2
4
3
#8 x 3/
4" Screw - 4
SHOWN ACTUAL SIZE
#10 x 7/8" Black Screw - 2
SHOWN ACTUAL SIZE
•Turn the seat bottom assembly upright.
•Fit the seat back pins into the openings in the top side of
the seat bottom assembly.
Seat
Bottom
Assembly
Seat Back
Pin
Seat Back
Pin
Opening
Opening
Assembly
•Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.
• Insert a #10 x 7/8" black screw into the hinge rod.
•Tighten the screw with a Phillips screwdriver.
Do not over-tighten.
•Set the seat assembly aside for Assembly step 11.
•Pull the frame leg out on each frame to open. Make sure it
“clicks” into place.
5
Hinge Rod
Long
Tap er ed
Leg Tube
Hinge
Frame Leg
• Identify the back and front base.The back base has short leg
tubes and the front base has long, tapered leg tubes.You will
use the back base for the next assembly step.
Front Base
Back Base
5
6
8
7
#10 x 7/
8" Black Screw
SHOWN ACTUAL SIZE
Short Leg
Tub e
Loading...