Page 1
Bubble Mower
™
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
No tools needed for assembly.
B0109
Instructions
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Page 2
1
IMPORTANT!
• Please make sure your child does not follow you using this toy while you
are operating a real lawn mower. Your child should play in a separate area
away from the area where you are mowing.
• Use only bubble solution in this toy.
• Make sure your child understands that bubble solution is not for drinking
and that is should be kept away from the eyes.
• While filling or cleaning this toy, try to avoid spilling bubble solution on the
floor. It may create slippery floor conditions.
Assembly
Handle
Peg
Hole
• Place the mower on an elevated, flat surface.
• Position the handle with the Fisher-Price®logo facing up.
• With the handle angled down, fit the holes on the ends of the handle onto
the pegs near the rear wheels.
Rear Wheel
2
Page 3
3
Assembly
2
• Lift the handle until it "snaps" into an upright position.
3
• Fit the storage tray onto the tabs on the handle. Press the storage tray until
it "snaps" in place.
Lift Handle
Storage Tray
Tabs
Page 4
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2003 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO B0109a-0920
4
Bubblin’ Fun
Hint: When using the mower with bubble solution, we recommend using it
outdoors on flat, level ground or in short grass.
• Carefully pour bubble solution into the spout on each side of the Bubble
Mower. Fill until bubble solution just reaches the top of the bubble chamber.
Do not over-fill.
Note: The maximum capacity of each bubble chamber is only about
2 tablespoons.
• Fit the bottle of bubble solution in the storage tray.
• Pull the starter lever for realistic mower sounds.
Note: The starter only pulls out a short distance.
Starter Lever
Fill To Here
Spout
Storage Tray
Page 5
• Push the bubble mower so that all four wheels contact the ground.
• Bubbles begin flowing after the mower has been pushed about 15-20
walking steps. As long as the mower is being pushed the bubbles continue
to flow.
• If your mower does not make bubbles:
- Check to be sure there is enough bubble solution in the mower.
- Make sure all four wheels contact the ground when pushing the mower.
- Empty the bubble solution from the mower. Refill the mower with fresh
bubble solution.
- Wash the bubble chamber (see “Let’s Clean Up”), and refill with fresh
bubble solution.
Note: We do not recommend the use of silicones or oily lubricants on this
toy. As with any bubble producing toy, when even a very small amount of
silicone or oily lubricants are put into or used near the bubble chambers,
bubbles will not form.
5
Bubblin’ Fun
Page 6
6
Let’s Clean Up
• Insert the cover tabs into
the slots in the mower .
Press the top of the cover
to fit the cover in place .
B
A
Bubble Wheel
Cover
IMPORTANT! You must clean this toy after each use. Dried bubble solution
inside the mower may affect how this toy makes bubbles. Please follow the
instructions in this section carefully.
B
B
A
A
•Tip the mower forward to empty the
bubble solution.
• Lift up on a cover then pull
it away from the mower to
remove it. Repeat this
procedure to remove the
other cover.
• Thoroughly rinse the bubble wheel
and bubble chamber on each side of the
toy with clean water from a garden hose
or faucet. Rotate the back wheels a few
times, then pour the water out.
LIFT
1
2
3
4
Page 7
Problems and Solutions
Not enough bubble
solution in chamber(s)
Bubble chamber
wheel(s) is clogged
and dirty
You have not walked
far enough to produce
bubbles
You are walking too
quickly
The rear wheels are not
contacting the ground.
Silicone or oily
lubricants may have
gotten in the bubble
chamber(s)
Bubble chamber(s)
over-filled
The mower is used on
an incline
Refill chamber(s) with
enough bubble solution.
Follow instructions
in “Let’s Clean Up”
section to clean bubble
chamber thoroughly.
The bubble mower
needs to be pushed
a minimum of 15-20
walking steps before
bubbles begin to flow.
Walk at a slow,
steady pace.
Push the mower so that
the rear wheels are
always contacting the
ground.
Never use silicone or
oily lubricants on this
product (the wheels).
Bubbles will not form
if even a very small
amount of these
substances get into
the bubble chamber(s).
Fill only until bubble
solution reaches top of
bubble chamber.
Use the Bubble Mower
only on flat, level
ground.
Problem Cause Solution
Bubbles do not flow
from one or both
bubble chambers
Bubble solution
is leaking from
the mower
7
Page 8
Storage
• Remove the handle for long-term storage. First lower the handle, then pull
the ends of the handle out.
• Rinse the mower thoroughly with clean water before storing it for long
periods of time.
• This toy has no consumer serviceable parts. Do not take this toy apart.
Consumer Information
Questions? We’d like to hear from you!
Call Fisher-Price®Consumer Relations, toll-free at 1-800-432-5437,
8 AM- 6 PM EST Monday through Friday. Hearing-impaired consumers
using TTY/TDD equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®Consumer Relations, 636 Girard Avenue, East Aurora,
New York 14052.
Handle
For countries outside the United States:
CANADA Questions? 1-800-567-7724. Mattel Canada Inc., 6155 Freemont Blvd., Mississauga,
Ontario L5R 3W2.
GREAT BRITAIN Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500302.
AUSTRALIA Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121
Australia. Consumer Advisory Service 1300 135 312.
NEW ZEALAND 16-18 William Pickering Drive, Albany 1331, Auckland.
ASIA Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City,
Tsimshatsui, HK, China.
Loading...