Fisher-Price 92082 Instruction Sheet
92082-0920
Keep these instructions for future reference: they contain important information.
❶
I. FEATURES
2 Power Options
Full Function
27 MHz/49 MHz
Range up to 60'/18m
This vehicle can operate on 2 different power
systems: the included 6V DP™ Power Clip,
which uses 4 “AA” batteries (not included);
and the 6.0V Jet Turbo
®
rechargeable NiCd battery pack. You’ll find detailed instructions about
both systems in this Owner’s Manual.
II. VEHICLE
Top View
❶ ON/OFF Switch
❷ Battery Door Cover
❸ Battery Door Latches (2)
❹ Battery Compartment
❺ Battery Compartment Latch
❻ Steering Adjuster (adjust for straight
vehicle tracking if necessary)
Side View
❶ Powerful Outboard Motor
❷ “Turbo” Propeller Drive
❸ Rudder
III. TRANSMITTER
NOTE: Your transmitter is equipped with a special automatic -ON battery-saving feature. Just
turn your vehicle ON. Then push either transmitter stick and you will be able to run and
control your vehicle.
❶ Left Stick Controls Forward & Reverse
❷ Whip Antenna
❸ Right Stick Controls Left & Right Turns
❹ Power Indicator Light
Refer to label on transmitter and vehicle for
frequency. Don’t operate near vehicles with
the same frequency.
6V DP BOAT
6V DP BOAT
Store vehicle on foam display base when not in use.
™
❹
❶
❷
❻
❺
❸
❶
❷
❸
❹
❷
❸
POWER OPTION ONE
6V DP™ POWER CLIP
4 AA BATTERIES NOT INCLUDED
1. Unscrew Power Clip cover screw and
remove cover. Insert 4 “AA” batteries, with
polarity (+/-) as shown, inside Power Clip.
Replace cover.
2. Turn battery door latches to open position
and remove battery door.
3. Release battery compartment latch.
4. Insert Power Clip into battery compartment
and slide Power Clip away from latch.
5. Make sure Power Clip snaps securely in
place, turn battery compartment latch to
lock Power Clip in place.
6. Replace battery door. Turn battery door
latches until they click securely into place.
7. To remove Power Clip: open battery door, fol-
lowing steps above. Turn battery compart-
ment latch, slide Power Clip away from latch
and lift out.
Battery Contacts
Bent or dirty contacts may result in loss of
power. If battery does not fit correctly, gently
bend back metal contact as shown in diagram.
IMPORTANT DISPOSABLE BATTERY INFORMATION
Insure that battery polarity is correct.
Use only batteries of the type recommended
(or equivalent).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel-cadmium) batteries.
Remove used-up batteries immediately.
Remove batteries if vehicle will not be used
for a long period.
For best performance use alkaline batteries
(where disposable batteries are called for).
Battery life may vary depending on battery
brand.
Do not recharge non-rechargeable batter-
ies.
Do not short-circuit terminals.
Remove rechargeable batteries before
recharging. Recharge batteries only under
adult supervision.
Dispose of batteries safely.
NOTE: The batteries used in the 6V DP Power
Clip will gradually lose power over their lifetime. You will notice a decrease in performance as this occurs. The 6.0V Jet Turbo
rechargeable NiCd battery pack will run at a
sustained high power level for virtually its
entire run time.
POWER OPTION TWO
6.0V JET TURBO
®
RECHARGEABLE NiCd BATTERY PACK
Please read Battery Charging/Care on the next
page.
1. Turn battery door latches to open position
and remove battery door.
2. Release battery compartment latch.
3. Insert battery pack into battery compartment
and slide battery pack away from latch.
4. Make sure Power Clip snaps securely in
place, turn battery compartment latch and
lock Power Clip in place.
5. Replace battery door. Turn battery door
latches until they click securely into place.
6. To remove battery pack: open battery door,
following steps above. Turn battery compartment latch, slide battery pack away from
latch and lift out.
TRANSMITTER
1. Slide battery door open.
2. Install one 9-volt battery with polarity (+/-) as
shown inside battery compartment.
3. Replace battery door.
❶
❷
Battery Contacts
Loading...