Fisher-Price 79740 Instruction Sheet
Model Number: 79739
INSTRUCTIONS
It’s a swing. It’s a two-position high chair.
Use it as a traditional swing to soothe and entertain baby with
head-to-toe swinging motion and then convert it to a high chair!
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
Requires three “D” (LR20) alkaline batteries for operation (not included).
SWING ‘N MEALS
™
High ChairSwing
This package contains small parts.
Adult assembly is required.
CAUTION
PARTS
SHOWN ACTUAL SIZE
#8 x 11/4" Screw – 2
Large High Chair Tray
Small Swing Tray
Reversible Pad
Seat Frame
2 Plastic
Housings
Rear Base
Front Base
2 Rear Legs
2 Front Legs
Seat
• Never leave child unattended.
• To prevent falls when using the swing, never use with an active child who may
be able to climb out of the seat.
• Always keep child in view while in product.
• Prevent serious injury or death from falls or sliding out. Always use the restraint
system. Never rely on the tray to restrain child.
• The child should be secured in the product at all times by the restraining
system. The tray is not designed to hold the child in the chair. It is
recommended that the product be used as a high chair only by children
capable of sitting upright unassisted.
WARNING
WARNINGS
2
• Position a plastic housing so that the hub is toward the seat.
• Fit the seat frame tube into the hub on the plastic housing.
• Insert a screw into the hub and through the seat frame tube.
• Tighten the screw with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to assemble the other plastic housing to the
other seat frame tube.
• Remove the temporary instructional labels (one on each hub) that
reminded you to fasten the screws. Dispose of the labels properly.
• Position the seat frame on a flat surface.
• Fit the hole in the seat hubs onto the seat frame tubes.
• Press the upper buttons on the seat frame tubes and slide the
seat down.
• Press the middle buttons on the seat frame tubes and slide the
seat down.
• Press the lower buttons on the seat frame tubes and slide the
seat down.
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price
®
for replacement parts and instructions if needed. Never substitute parts.
3
ASSEMBLY
1
2
#8 x 11/4" Screw – 2
Hub
Seat Frame Tubes
Hole
Press Button
Press Button
Press Button
Press Button
Press Button
Press Button
Hub
Seat Frame Tube
Plastic
Housing
• Position the seat assembly so that the front of the seat is upright.
• Locate the hole in the plastic housing marked .
• Insert the front left leg marked into the hole in the plastic
housing marked .
• Press the button on the front left leg and continue to insert the
front left leg into the hole in the plastic housing until it “snaps”
into place. Make sure you hear a “snap”.
• Pull the front left leg. It should remain secure. If you can remove
the front leg, you have assembled it incorrectly. Please remove it
and repeat step 4.
• Repeat this procedure to attach the front right leg marked into
the hole in the other plastic housing marked .
ASSEMBLY
3
5
4
6
Front
Right Leg
Front
Left Leg
Rear
Right Leg
Rear
Left Leg
• Identify the front legs and the rear legs. Each is marked:
Front right leg Rear right leg
Front left leg Rear left leg
Button
Front Left Leg
Front Right Leg
Seat Assembly
Plastic
Housing
Hole
4
• Position the front base so that the curved end faces down.
• Fit the front base tubes over the front legs.
• Press the buttons on the front legs. Continue to fit the front base
tubes onto the front legs until they “snap” into place. Make sure
you hear each tube “snap”.
• Pull the front base. It should remain secure. If you can remove the
front base, you have assembled it upside-down. Remove the front
base, turn it over and repeat step 5.
• Turn the assembly over so that the back of the seat is upright.
• Locate the slot in the plastic housing marked .
• Insert the rear left leg marked into the slot in the plastic
housing marked .
• Press the button on the rear left leg and continue to insert the
rear left leg into the slot. Lift the rear left leg up until it “snaps”
into place. Make sure you hear a “snap”.
• Pull the rear left leg. It should remain secure. If you can remove
the rear leg, you have assembled it incorrectly. Please remove it
and repeat step 6.
• Repeat this procedure to attach the rear right leg marked into
the slot in the other plastic housing marked .
Buttons
Front Legs
Front Base
Button
Rear
Left Leg
Plastic
Housing
Slot
Loading...