Fisher-Price 79666, B2110, B2109, B2111 Instruction Sheet
Model Numbers: 79666, B2109, B2110,B2111
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver (not included).
Product features and decorations may vary from the photo above.
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Infant to Toddler
High Chair
2
Occasionally a consumer may experience a problem with
one of our products. If this should happen, please call us
toll-free, rather than return this product to the store. Usually,
we can solve the problem over the telephone or send you
replacement parts. Please call Fisher-Price® Consumer
Relations, toll-free at 1-800-432-5437,8 AM- 6 PM EST
Monday through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470.
Or,write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
For other countries,outside the United States:
Canada: call 1-800-567-7724,or write to: Mattel Canada Inc., 6155
Freemont Blvd., Mississauga,Ontario L5R 3W2.
Great Britain: telephone 01628 500302.
Australia: Mattel Australia Pty.Ltd.,658 Church Street,Locked Bag #870,
Richmond,Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive,Albany 1331,Auckland.
Consumer InformationWarning
Prevent serious injury or death
from falls or sliding out.
• The child should be secured in
the high chair at all times by the
restraining system, either in the
recline, semi-recline or upright
position. The restraint belts must
be adjusted to fit your child
snugly. The tray is not designed
to hold the child in the chair.
• Always keep child in view while
in the high chair.
•Never leave child unattended.
• It is recommended that the high
chair be used in the upright
position only by children capable
of sitting upright unassisted.
WARNING
3
Parts
Rear
Support
2 Retainers
Front
Support
4 Legs
Seat with
Restraint System
Restraint Post
Footrest
2 Bases
2 Armrests
Pad
Tray
Seat Tube
ALL SHOWN ACTUAL SIZE
2 Leg Caps
#8 x
3
/4" Screw - 7
#8 x 15/8" Screw - 2
#10 Lock Nut - 4
#8 Lock Nut - 2
#10 x 21/8" Screw - 4
IMPORTANT! All consumer assembled
screws must be fully tightened for
proper assembly of this product.
Assembly
4
IMPORTANT! Before each use or assembly,inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.Contact
Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
Legs
Notch
Notch
Base Tubes
Numbers
1
•Fit a leg cap into the openings of two legs, as shown.
•Push down on the leg cap to be sure it is secure, and there
is no gap between the top of the legs and the leg cap.
•Repeat this procedure to attach the other leg cap to the
other two legs.
Legs
Leg Cap
2
Leg Cap
Track
Armrest
3
•Position a base so that the notches face you.
•Position two legs so that the numbers face you.
•Fit a leg onto each base tube.
•Twist and push each leg until it "snaps" into each base tube.
•Repeat this procedure to assemble the remaining two legs to
the other base.
•Position an armrest so that the track is facing out.
•Fit the armrest onto a leg cap, as shown.
•Repeat this procedure to attach the other armrest to the
other leg cap.
This product contains small parts
in its unassembled state. Adult
assembly is required.
CAUTION
Assembly
5
•Turn the leg assembly, as shown, so that the armrests point
toward you.
•Position the front support so that the arrows are pointing
toward you.
•Fit the ends of the front support up between the inside of the
armrests and the front legs.
Armrest
Front
Leg
Front Support
Arrows
5
• Insert a #10 x 21/8" screw through the outside of an armrest,
a rear leg and then out through the inside of the armrest.
•Fit a #10 lock nut into the hexagonal opening on the inside
of the armrest. Make sure the rounded side is facing out.
• Fully tighten the screw with a Phillips screwdriver. When
properly tightened, the end of the screw will be visible,
as shown above.
•Repeat this procedure to secure the other armrest with a
#10 x 21/8" screw and a #10 lock nut.
Armrest
Rear Legs
#10 Lock Nut
#10 x 21/8" Screw - 2
Shown Actual Size
#10 Lock Nut - 2
Rounded Side
Shown Actual Size
End
of Screw
Visible
Lock Nut
4
Loading...