Fisher-Price 79636 User Manual
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Bouncer
Kick & Play
Model Number: 79636
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
Requires one “D”(LR20) alkaline battery (not included) in the soothing unit.
Requires three “AA” (LR6) alkaline batteries (not included) in the toy bar.
To prevent serious injury and/or falls:
• Never use on any elevated surface,
since child’s movement may cause
bouncer to slide or tip over.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Never use with a child able to sit
up, unassisted.
WARNING
Warning
2
Parts
3
Pad
Toy Bar
Removable
Teether Rings
Footrest with
Soothing Unit
2 Retainers
Seat
Back
Tube
Right Base Wire
Left Base Wire
Base
Tube
#8 x 3/4" Screw - 2
Shown Actual Size
• Locate the soothing unit on the footrest wire.
• Loosen the screw in the soothing unit battery compartment door with a
Phillips screwdriver. Remove the battery compartment door.
• Insert one “D” (LR20) alkaline battery, as indicated inside the battery
compartment.
• Replace the battery compartment door.Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
• Loosen the screw in the toy bar battery compartment door with a Phillips
screwdriver. Remove the battery compartment door.
• Insert three “AA”(LR6) alkaline batteries, as indicated inside the battery
compartment.
• Replace the battery compartment door.Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
Battery Installation
4
Toy Bar
Soothing Unit
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Battery leakage and corrosion can
damage this product. Dispose of batteries safely.
• Do not dispose of batteries in a fire.The batteries may explode or leak.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the
"Battery Installation" instructions are to be used.
• If removable rechargeable batteries are used, they are only to be charged
under adult supervision.
• Rechargeable batteries are to be removed from the product before they
are charged.
• If you use a battery charger,it should be examined regularly for damage to
the cord, plug, enclosure and other parts.Do not use a damaged battery
charger until it has been properly repaired.
5
1.5V
"D" (LR20)
SHOWN ACTUAL SIZE
1.5V x 3
"AA" (LR6)
SHOWN ACTUAL SIZE
+
_
Assembly
6
• Place the base tube on a flat surface
as shown.
• Position the left and right base wires as
shown. Note the locations of the colored
tab on the left and right base wires.
• Fit the left base wire into the base tube.
• Fit the right base wire into the base tube.
• Make sure both colored tabs on the base wires are visible through
the holes in base tube.
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
1
Base
Tube
Base
Wire
Colored Tab
Back View
Base
Tube
Colored Tabs
Right Base
Wire
Left Base
Wire
Loading...