Fisher-Price 79595, 79596 User Manual
Model Number: 79595, 79596
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver and Adjustable Wrench (both not included).
Requires three “D”(LR20) alkaline batteries for operation (not included).
Maximum Weight Limit:24 lbs. (10.9 kg.)
The maximum weight limit for this product is 24 lbs.
IMPORTANT! If your child weighs less than 24 lbs., but is really active and appears to be
able to climb out of the swing, immediately discontinue its use.
Swing
Cradle
Cradle Swing
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
2
Warnings and Caution
Parts
• To prevent falls, never use with
an active child who may be able
to climb out of the seat.
• Never leave child unattended.
• To prevent injury or death from
falls or sliding out, always use
restraint system. Never rely on
the tray to restrain child.
WARNING
This product contains small parts
in its unassembled state. Adult
assembly is required.
CAUTION
Motorized Frame
2 Lower
Legs
2 Upper Legs
Seat
2 Feet
2 Elbow
Feet
Tray
Mobile
Pad
Seat Tube
Activity Toy Bar
ALL SHOWN ACTUAL SIZE
#8 x 1/2" Pointed Screw - 2
M4 x 31.5 mm Bolt - 2
M4 Lock Nut - 2
#8 x 3/4" Pointed Screw - 2
Seat Tube
Arm
2
SHOWN ACTUAL SIZE
Assembly
1
3
Lower Leg
• Fit a foot onto the end of the lower leg.
• Insert a #8
1
/2" pointed screw through the bottom of the
foot and into the lower leg.Tighten the screw with a
Phillips screwdriver. Do not over-tighten.
• Repeat assembly steps 1 and 2 to assemble the other
elbow foot and foot to the other lower leg.
• Position one of the lower legs so that the long portion
is down.
• Fit an elbow foot,with the cup side down, onto the bend
in the lower leg.
• Insert a #8
3
/4" pointed screw through the bottom of the
elbow foot and into the lower leg.Tighten the screw with
a Phillips screwdriver. Do not over-tighten.
• Stand each lower leg upright, as illustrated.
• The elbow foot and foot should be flat against the floor.
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
Foot
Cup
Side
Down
• Position an upper leg so that the red dot is upward.
• While pressing the button on the straight end of an
upper leg, insert the upper leg into a lower leg. Make
sure the button on the upper leg “snaps” into the hole
in the lower leg.
• Repeat this procedure to assemble the other upper leg
to the other lower leg.
Elbow Foot
Lower Leg Long Portion
Lower Leg
Elbow Foot
Foot
SHOWN ACTUAL SIZE
#8 x 3/4" Pointed Screw - 2
#8 x
1
/2" Pointed Screw - 2
Correct Incorrect
3
4
Red Dot
Lower Leg
Upper Leg
Straight
End
Button
Hole
Assembly
5
6
8
4
5
7
• Position the motorized frame so that the battery
compartment is toward you.
• Position the tubes in the motorized frame so that they are
toward the outer edges.The holes in the tubes should be
visible through the notches in the motorized frame.
• Locate the R and L on the underside of each elbow foot.
The R indicates the right leg. The L indicates the left leg.
• While pressing the upper button on the right leg, fit it
into the tube in the motorized frame. Make sure the
upper button on the right leg “snaps” into the hole in
the tube.
• While pressing the button on the left leg, fit it into the
tube in the motorized frame. Make sure the button on
the left leg “snaps” into the hole in the tube.
• When the legs are assembled correctly to the tubes in the
motorized frame, you should not see the red dots.
Tub e
Hole
Red Dot
Motorized Frame
• Stand the assembly upright. All four feet should be flat upon
the floor.Also, when standing behind the product, check for
an L marking on the left foot and an R marking on the
right foot.
• If the feet are not flat upon the floor, or the left and right feet
have been reversed, simply remove both legs and replace
them on the opposite tube in the motorized frame. Again,
check to be sure all four feet are flat upon the floor.
Feet
Button
Feet
Tub es
Hole
Motorized
Frame
Battery
Compartment
Hole
Elbow Foot
L
R
L
R
• Position the seat upright.
• Place the pad onto the seat with the
ruffle toward the top of the seat.
• Fold the top of the pad down.Insert the waist belts through
the slots in the pad. Make sure the waist belts are not twisted.
• Insert the two elastic loops on the pad through the holes in
the seat bottom.
• Fold the bottom of the pad up.Insert the crotch belt through
the slot in the pad. Make sure the crotch belt is not twisted.
Seat
Elastic
Loops
Waist
Belts
Pad
Crotch Belt
Loading...