Fisher-Price 79070 User Manual

Model Number: 79070

INSTRUCTIONS

Please read and understand these instructions before assembly and use.

Keep these instructions for future reference.

Tool needed for assembly: Phillips Screwdriver (not included).

Maximum weight limit: 26 lbs.

SOUNDS ‘N LIGHTS

PORTABLE ENTERTAINER

™

Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Usually we can solve the problem on the telephone or by sending you replacement parts. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Fisher-Price® Consumer Relations, 636 Girard Avenue, East Aurora, New York 14052.

To prevent serious injury or death:

• Use only for a child who is able to hold head upright unassisted and who is not able to walk.

• Never leave child unattended. Always keep child in view while in product.

• Never use near steps or pools, hot surfaces or areas that may be hazardous to a child. Product may move during use.

• To avoid tip over, place product on a flat, level surface.

WARNING

WARNINGS

CONSUMER INFORMATION

/8" Screw with Washer Head – 7

SHOWN ACTUAL SIZE

M5 39/16" Bolt - 2

Seat Ring

Seat Pad

Hub

Spring

Button

2 Retainers

4 Toy Rings

Toy Bar

Head

Base

Tray

Base

2 Legs

4 Screws with Washer Heads

IMPORTANT! Please remove all parts from the package and identify them before assembly.

2 M5 Lock Nuts

M5 Bolt

PARTS

Caterpillar

3 Screws with Washer Heads

/16" Washer - 2

SHOWN ACTUAL SIZE

M5 Lock Nut - 2

SHOWN ACTUAL SIZE

/16" Washer

• Rotate the legs down.

• Make sure the treads on all four rubber feet are facing down. If the treads on all four rubber feet are not facing down, you have assembled the legs incorrectly. Remove the legs from the curved tubes (press the buttons on the legs to release them from the curved tubes) and re-read and repeat step 2.

• Place a base on a flat surface.

• While pressing the button on the side of the base, lift the frame to the highest position. The button should be in the highest position.

• Repeat this procedure to raise the other frame on the other base to its highest position.

• Make sure the button on each base is in the highest position.

IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. Do not use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions needed. Never substitute parts.

Frame

Base

Button

Highest Position

Lowest Position

Leg

• Position a leg so that the buttons are down and the treads on the rubber feet face up.

• While pressing the buttons on the leg, insert and "snap" the ends of the leg into the curved tubes on the base.

• Repeat this procedure to attach the other leg to the bases.

Treads Up

Leg

Curved Tube

This product contains small parts in its unassembled state.

Adult assembly is required.

CAUTION

• Place the tray upright on a flat surface.

• Fit the caterpillar to the top of the tray. From the bottom of the tray, insert three

/8" screws with washer heads through the tray and into the caterpillar. Tighten the screws with a Phillips screwdriver. Do not over-tighten.

• Slide the four rings onto the toy bar.

• Insert and "snap" the toy bar into the holes in the tray.

• Pull up on the toy bar to make sure it is secure.

Rings

Tray

Hole

Toy Bar

Treads Down

ASSEMBLY

Caterpillar

• Fit the hubs to each side of the tray.

• Hold the hubs in place.

Tray

Hub

• Position the hub with the inside facing up.

• Align the tab on the button with the slot in the hub.

• Fit the button into the hub.

• Place a spring inside the button.

• Repeat this procedure to assemble the other button and spring to the other hub.

Slot

Button

Spring

Tab

Hub

• While holding the hubs in place, pick the tray up and turn it so that the bottom faces you.

• Locate the raised dot on one side of the tray, near the hub.

• Locate the raised dot on one of the frames.

• Align the raised dot on the tray with the raised dot on the frame.

• Fit the hubs into the round wells in the frames.

Tray

Round Wells

Hold

Hubs

Hold

Hubs

Raised Dot

Bottom View

Side View

Raised Dot

Side View

Raised Dot

Hub

ASSEMBLY

+ 11 hidden pages