Fisher-Price 77306 User Manual
Model Number 77306
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four "C" (LR14) alkaline batteries for control tower; four "AA"
(LR6) alkaline batteries for car; and one 9V (6LR61) alkaline battery
for remote controller (batteries not included).
Adult assembly is required.
Tool required for assembly:
Phillips screwdriver (not included).
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Grow With Me
RC Rally
Grow With Me
RC Rally
Grow With Me
RC Rally
™
Parts
2
5 Barrels
Crash Gate
Flexible
Track
3 Cones
Dirt Track
Ring of Fire
Handle
Support
Control
Tower
Handle
2 Flags
Double
Flag
Ramp
2 Ramp Rails
Starting Ramp
3 Hay
Bales
4 Stadium
Lights
Remote
Controller
Car
Remote
Controller
Holder
#6 x 5/8" Screw - 7
Shown Actual Size
Label sheet not shown.
Car
Battery Compartment Door
1.5V x 4
“AA” (LR6)
Shown Actual Size
• Locate the battery compartment
on the bottom of the car.
• Loosen the screw in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
• Insert four "AA" (LR6) alkaline
batteries, as indicated inside the
battery compartment.
• Replace the battery compartment
door and tighten the screw with
a Phillips screwdriver. Do not
over-tighten.
Battery
Compartment
Door
Battery Installation
3
• Locate the battery compartment
on the back of the control tower.
• Loosen the screws in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
• Insert four "C" (LR14) alkaline
batteries, as indicated inside the
battery compartment.
• Replace the battery compartment
door and tighten the screws with
a Phillips screwdriver. Do not
over-tighten.
Control Tower
1.5V x 4
“C” (LR14)
Shown Actual Size
4
Battery Installation
Remote Controller
Battery
Compartment
Door
9V
9V (6LR61)
Shown Actual Size
• Locate the battery compartment
on the back of the remote
controller.
• Loosen the screw in the battery
compartment door with a
Phillips screwdriver. Remove
the battery compartment door.
• Insert one 9V (6LR61) alkaline
battery, as indicated inside the
battery compartment.
• Replace the battery compartment door and tighten the screw
with a Phillips screwdriver. Do
not over-tighten.
5
Battery Tips
• We recommend using alkaline batteries for longer battery life.
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc)
or rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Battery leakage and corrosion can
damage this toy. Dispose of batteries safely.
• Do not dispose of batteries in a fire. The batteries may explode or leak.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the
"Battery Installation" instructions are to be used.
• If removable rechargeable batteries are used, they are only to be
charged under adult supervision.
• Rechargeable batteries are to be removed from the toy before they
are charged.
• If you use a battery charger, it should be examined regularly for
damage to the cord, plug, enclosure and other parts. Do not use a
damaged battery charger until it has been properly repaired.
When To Replace Batteries
If this toy is working slowly or erratically, it’s likely that batteries need
to be replaced. While it is possible that all batteries may need replacement, the batteries that will need replacement most often are the
batteries in the car, followed by the remote controller, and then the
control tower. For more information, see the troubleshooting guide
beginning on page 19.
• Position the handle support so
the pegs are facing you.
• With the checkered side facing
down, fit the double flag on to
the pegs on the handle support.
6
• Fit the handle onto the handle
support as shown.
Assembly
2
3
111
Pegs
Double
Flag
Handle
Support
Handle
Support
Handle
WARNING
This product contains small parts in its unassembled
state. Adult assembly is required.
• Insert three screws through
the holes in the handle and
into the handle support. Tighten
the screws with a Phillips
screwdriver. Do not over-tighten.
• "Snap" the remote controller
holder onto the tab on the bottom
of the starting ramp, as shown.
• Insert and "snap" the pegs on
the bottom of the handle
assembly into the matching holes
in the starting ramp as shown.
4
5
7
• Insert the handle and starting
ramp into the matching holes in
the control tower as shown.
• Lift the control tower storage
compartment door. Insert two
screws through the control tower
and into the handle. Tighten the
screws with a Phillips screwdriver.
Do not over-tighten.
• Insert two screws through the
holes near the bottom of the
control tower and into the pegs in
the starting ramp. Tighten the
screws with a Phillips screwdriver.
Do not over-tighten.
Assembly
Handle
Assembly
Starting
Ramp
Pegs
Starting
Ramp
Remote
Controller
Holder
Handle
Control
Tower
Tab
6
8
Assembly
7
• Insert and "snap" the tabs on
the ramp into the matching
slots in a ramp rail.
• Repeat this procedure to
attach the other ramp rail.
• Gently squeeze the ring of fire
to insert the pegs on either
end into the matching holes at
the top of the ramp assembly,
as shown.
Ramp
Rail
Ramp
Tabs
Ramp
Ramp
Assembly
Ramp
Rail
Ring of Fire
Peg
Peg
Hole
Hole
Loading...