Fisher-Price 76960 User Manual

TM
Super Talk!™BARBIE™Sun Jammer
4x4
Please read this manual and save it with your original sales receipt.
For Model 76960
Tools needed for assembly: Phillips Screwdriver, Slotted Screwdriver, Hammer, Safety Scissors.
Use only with Power Wheels®Type H (9.5 Amp/hr.) Batteries, Power Wheels®30 Amp Fuses and
Power Wheels®Type H 12 Volt Charger (all included).
Requires three “AAA” (LR03) alkaline batteries (not included) for the phone.
CAUTION
ELECTRIC TO Y : Not recommended for children under 3 years of age.
As with all electric products, precautions should be observed during
handling and use to prevent electric shock.
Product features may vary from the picture above.
WARNING
• Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, batteries or help in assembly of the vehicle.
• Keep small parts such as the “AAA” batteries and plastic bags out of children’s reach. Dispose of plastic bags properly.
• Adult supervision is required. Children do not have the judgement necessary to avoid many accidents. Be sure that children operating this vehicle can do so safely and that they are supervised at all times.
• Improper use of this vehicle could lead to a serious or fatal accident. Allow children to play with this vehicle only when you have determined that they can do so safely. Follow all instruc­tions to help your child enjoy this vehicle as safely as possible.
• Never use near steps, driveways, steep inclines, roadways, alleys, swimming pool areas or other bodies of water.
• Always wear shoes or sneakers when operating or riding in this vehicle.
• Never allow more than two riders; one driver and one passenger.
• Riders should sit on the seat when the vehicle is in operation.
Hot motor covers. Handle carefully.
• Never alter this vehicle or its electrical system in any way. Alterations could cause a fire resulting in injury and could also ruin the electrical system.
• Use of the wrong type battery, fuse or charger could cause a fire or explosion, resulting in serious injury.
• Never add unauthorized parts to the vehicle or use substitute parts. Use only specified Power Wheels
®
replacement parts.
• Batteries must be handled by adults only.
• Never lift or carry the 6 volt batteries by the wires or connectors. This can damage the 6 volt batteries and possibly cause a fire resulting in injury. Lift and carry the 6 volt batteries by the cases only.
• Never permit a child to handle batteries. The 6 volt batteries are heavy and contain sulfuric acid (electrolyte), and if dropped, could result in serious injury. Read the cautions on the back panel of the 6 volt battery.
• Never allow children to charge the 6 volt batteries. Battery charging must be done by adults only. A child could be injured by the electricity involved in charging batteries.
• Examine the 6 volt batteries, charger and their connectors for excessive wear or damage each time you charge the 6 volt batteries. If damage or excessive wear is detected, do not use the vehicle until you have replaced the worn or damaged part as it could possibly cause a fire resulting in injury.
• Placing the “AAA” (LR03) batteries in the phone with the positive (+) and negative (-) markings the wrong way could cause damage or over-heating resulting in injury. The “AAA” (LR03) batteries must be positioned as shown on the battery compartment door.
2
Throughout this manual you will find important messages in the form of WARNINGS, CAUTIONS, and NOTES.
WARNING
WARNING – SIGNALS SOMETHING THAT
COULD HURT YOUR CHILD OR YOU.
The message explains the hazard and
how you can avoid it.
CAUTION
• Do not operate your vehicle for the first time until you have inserted the 30 amp fuses into the 6 volt batteries and charged the 6 volt batteries for at least 18 hours. Never charge the 6 volt batteries longer than 30 hours.
• After first-time use, charge the 6 volt batteries for at least 14 hours after each use. You do not have to let the 6 volt batteries run down completely before recharging. Never charge the 6 volt batteries longer than 30 hours.
• Use the charger indoors only.
• Read and follow the Battery Care instructions on page 33. Failure to follow the Battery Care instructions may permanently damage your 6 volt batteries and will void your warranty.
• When you purchase replacement 6 volt batteries, you should buy a set. Using an older 6 volt battery with a new 6 volt battery may cause permanent damage to both 6 volt batteries.
• To avoid damaging motors and gears, do not overload the vehicle.
- Never allow more than two children in the vehicle at one time; one driver and one passenger.
- Do not exceed the maximum weight capacity of 130 lbs.
- Do not tow anything behind the vehicle. The extra weight may overload it.
• Avoid operating the vehicle in wet or snowy conditions, and do not spray the vehicle with a hose. Do not wash the vehicle with soap and water. Water or moisture in the motors or electrical switches can cause them to corrode, and could cause switch failure.
• Avoid operating the vehicle on sand, loose dirt or gravel. Sand, loose dirt and gravel in the electrical switches or motors can cause them to jam, and could cause switch failure. Use this vehicle on grass, asphalt or other hard surfaces.
3
CAUTION
CAUTION – SIGNALS SOMETHING THAT
COULD DAMAGE THE VEHICLE.
The message explains the risk and
how you can avoid it.
NOTE – Is used to highlight useful information.
Table of Contents
A Message to Parents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
B Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
D Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
E First-Time 6 Volt Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
F Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
G 6 Volt Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
H Charging the 6 Volt Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
I Battery Handling/Care/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
J Rules for Safe Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
K How to Operate Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
L Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
M Problems and Solutions Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
N Statement of Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
O Authorized Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
4
Message to Parents
Thank you for purchasing the Power Wheels
®
Super Talk™BARBIE™Sun Jammer™4x4! For over 30 years, Power Wheels®has manufactured high­quality, battery-powered vehicles for children. Our goal is to provide your child with an enjoyable and safe driving experience. To help achieve this goal, it is extremely important that you read this entire manual and share the appropriate information with your child.
Your vehicle requires adult assembly. Please set aside at least 60 minutes for assembly. Read the assembly instructions carefully and identify all parts before assembly. Refer to the Parts Section beginning on page 6 for parts identification. Save all packaging material until assembly is complete to ensure that no parts are discarded.
In the unlikely event that parts are missing or damaged or if you have any questions about your Power Wheels®vehicle, please call our Consumer Affairs toll-free service lines, open from 8 AM to 6 PM (EST) Monday through Friday.
A
Please call us at 1-800-348-0751.
Trained customer service representatives are available to take your call in English or French.
¿Habla Español? Si usted tiene alguna pregunta ó necesita asistencia llame gratis 1-800-348-0755 para los Estados Unidos. Tenemos representantes que hablan español para atender su llamada.
We also have a nationwide Authorized Service Center network – with over 300 Authorized Service Centers. Our Authorized Service Centers will repair or replace parts under warranty at no charge. For vehicles beyond warranty, our Authorized Service Centers will perform repairs for a minimal charge. For the Authorized Service Center nearest you, please see the Authorized Service Center listing beginning on page 43.
Important Information
• Carefully read this manual for important safety information and operating instructions before using your vehicle.
• Please complete and return the enclosed Registration Card, or call 1-800-348-0751 to register your vehicle by phone.
• This vehicle is designed for use by children 3-7 years.
• Adult assembly is required.
• This vehicle has adjustable play seat belts. Please note that the adjustable seat belts are designed to be a play feature only and do not function as protective safety restraints.
• This vehicle uses two Power Wheels®Type H 6 volt (9.5 Amp/hr.) batteries with Power Wheels®30 amp fuses and a Power Wheels®Type H 12 volt charger (120 VAC 60 HZ 28W with an output of 12 VDC 1200 mA). Do not substitute any other batteries, fuses or charger.
Before first-time use, charge the 6 volt batteries for
at least 18 hours. Never charge the 6 volt batteries longer than 30 hours.
• After the first charge, charge the 6 volt batteries a minimum of 14 hours after each use. Never charge the 6 volt batteries longer than 30 hours.
• Do not run down the 6 volt batteries completely before charging.
• Leaving the 6 volt batteries in a discharged condition will ruin them.
• Charge the 6 volt batteries before storing your vehicle.
• Charge the 6 volt batteries at least once per month, even if the vehicle has not been used.
• Do not store the 6 volt batteries in temperatures above 75˚ F or below -10˚ F.
• Even with proper care, the 6 volt batteries will not last forever. The life of the 6 volt batteries depends on how well you follow the Battery Care instructions and the total number of hours the 6 volt batteries are used. Please refer to the BatteryHandling/ Care/Disposal instructions on page 33 for detailed information about battery care.
B
5
• When you purchase replacement Power Wheels
®
Type H (9.5 Amp/hr.) batteries, you should buy them as a set. Using an older 6 volt battery with a new 6 volt battery may result in poor performance and may cause permanent damage to both 6 volt batteries. Remember to charge new 6 volt batteries for at least 18 hours before first use.
• To purchase Power Wheels®Type H 6 volt batteries, Power Wheels®30 amp fuses or a Power Wheels
®
Type H 12 volt charger, please contact:
- the store where your vehicle was purchased.
- an Authorized Service Center (see Authorized
Service Center list beginning on page 43).
- Power Wheels®Consumer Affairs at 1-800-348-0751.
• While the 6 volt batteries are charging, the charger may become warm to the touch. This is a normal condition and does not indicate a problem.
• This vehicle is suitable for use on grass, asphalt or other hard surfaces. To prevent damage to the motors and switches, do not operate the vehicle on loose dirt, gravel or sand.
• To prevent damage to electrical components, store the vehicle inside or under a protective cover during snowy or rainy weather. Do not leave the vehicle out in the rain or let your child wash it with soap and water.
• This vehicle has a special circuit-breaker in the wiring to protect the motors and electrical system. If the vehicle is put under extreme load (driving on rough surfaces, too much weight, climbing too steep an incline), the circuit-breaker will shut the electrical system down for up to 20 seconds. If the system repeatedly shuts down, the driving conditions may be too demanding (ie: too steep or too much weight).
• Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant.
Parts
C
Sport Bar Support – 2
1
2
3
4 5
6
7
8
12-VOLT
CHARGER
12 Volt Charger
Sport Bar Swivel – 2
Lens Guard – 2
Battery Retainer
6
If you experience a problem with this product, or are missing a part, please call us
at 1-800-348-0751, rather than return this product to the store.
Please save all packaging material until assembly is complete to ensure that no parts are discarded.
Dashboard Plate
Phone Holder Clip
Headlight Lens – 2
Turn Signal Lens – 2
Taillight Housing Set
Taillight Lens Set
Gas Cap Assembly
Steering Wheel Cap
Phone
Sport Bar Bracket – 2
Short Seat Belt Strap – 2
Long Seat Belt Strap
Phone Holder
Canopy
Key Chain
Knob Plate
#8 x 1" Screw – 10
#8 x3/4" Screw – 8
Hood Latch – 2
#10 x 1" Screw – 2
#6 x 1" Screw – 1
30 Amp Fuse – 3*
Dashboard Knob – 2
Windshield
Front Bumper
Rear Bumper
Sport Bar
Not Shown: Label Sheets
6 Volt Battery – 2
Steering Column
7
Parts
Cap Nut – 3*
All Screws Shown
Actual Size
Vehicle Body
Dash
Hood
Seat
* For your convenience, an extra 30 amp fuse
and cap nut have been included.
**#3 x
3
/8" screws found in phone.
Steering Wheel
Key Assembly
#8 x1/2" Screw – 2
Light Cover – 2
Light Rack, Rear Light Rack, Front
#10 x1/2" Screw – 2
#6 x 11/2" Screw – 4
1
/4" x 11/2" Machine Screw – 2
#3 x 3/8" Screw – 2**
Parts Diagram
D
1 Dash 2 Dashboard Plate 3 Steering Wheel 4 Steering Wheel Cap 5 Phone 6 Phone Holder 7 Phone Holder Clip 8 Key Chain 9 Dashboard Knob – 2 10 Knob Plate 11 Key Assembly 12 Windshield 13 Headlight Lens – 2
14 Lens Guard – 2 15 Turn Signal Lens – 2 16 Sport Bar 17 Sport Bar Swivel – 2 18 Sport Bar Support – 2 19 Light Cover – 2 20 Canopy 21 Sport Bar Bracket – 2 22 Light Rack – Rear 23 Light Rack – Front 24 Hood Latch – 2 25 Gas Cap Assembly 26 Taillight Lens – 2
27 Taillight Housing – 2 28 Rear Bumper 29 Vehicle Body 30 Seat 31 Short Seat Belt Strap – 2 32 Long Seat Belt Strap 33 Hood 34 6 Volt Battery – 2 35 Battery Retainer 36 Steering Column 37 Front Bumper 38 12 Volt Charger
Not Shown: Label Sheet – 2
Parts
8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
12-VOLT CHARGER
9
First-Time 6 Volt Battery Charging
E
WARNING
• Batteries must be handled by adults only.
• Never allow children to charge the 6 volt batteries. Battery charging must be done by adults only. A child could be injured by the electricity involved in charging batteries.
• Use of the wrong type battery, fuse or charger could cause a fire or explosion, resulting in serious injury.
• Never permit a child to handle batteries. The 6 volt batteries are heavy and contain sulfuric acid (electrolyte), and if dropped, could result in a serious injury. Read the cautions on the back panel of the 6 volt battery.
• Never lift or carry the 6 volt batteries by the wires or connectors. This can damage the 6 volt batteries and possibly cause a fire. Lift and carry the 6 volt batteries by the cases only.
• Examine the 6 volt batteries, charger and their connectors for excessive wear or damage each time you charge the 6 volt batteries. If damage or excessive wear is detected, do not use the charger or the vehicle until you have replaced the worn or damaged part.
• Never alter this vehicle or its electrical system in any way. Alterations could cause a fire resulting in injury and could also ruin the electrical system.
CAUTION
• Do not operate the vehicle for the first time until you have inserted 30 amp fuses into the 6 volt batteries and charged them for at least 18 hours. Never charge the 6 volt batteries longer than 30 hours.
• Carefully read the Battery Care instructions to obtain the best battery life. Failure to follow the Battery Care instructions may permanently damage your 6 volt batteries and may void your warranty.
• Use the charger indoors only.
We recommend that you start charging the 6 volt batteries before beginning assembly of your vehicle. Your new 6 volt batteries must be charged for at least 18 hours before you use
your vehicle for the first time.
®
®
• Squeeze the Lock-In
TM
connector tabs on the charger connector and plug it into the battery connector.
• Plug the charger into a standard 120 volt wall outlet.
Note: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”.
• Before first time use, charge the
6 volt batteries for at least 18 hours. Never charge the 6 volt batteries longer than 30 hours.
Note: The 6 volt batteries must be upright while charging.
2
3
Battery Connector
Charger Connector
Lock-In
TM
Connector Tabs
First-Time 6 Volt Battery Charging
10
• Insert a 30 amp fuse into each 6 volt battery.
Note: The top of the fuse will not be flush with the top of the 6 volt battery when properly installed.
• Stack one battery connector on top of the other and snap them together.
®
®
®
1
30 Amp Fuse
Battery Connectors
Charger
®
®
IMPORTANT
A 25 AMP FUSE MUST
BE INSTALLED IN TOP OF BATTERY BEFORE
TOY WILL RECHARGE OR OPERATE
IMPORTANT
A 25 AMP FUSE MUST
BE INSTALLED IN TOP OF BATTERY BEFORE TOY WILL RECHARGE
OR OPERATE
Assembly
Do Not Omit Any Steps. Please set aside at least 60 minutes for assembly.
• Apply labels to the dashboard plate, knob plate, and both sides of the key chain as shown. Make sure the areas where the labels will be applied are clean and dry. For best adhesion, avoid applying labels more than once.
Dashboard Plate
Knob Plate
1
11
F
COOL
HEAT
15
13
13
Key Assembly
Knobs
19
• Snap the key assembly into the
dashboard plate.
• Insert the key chain end through
the key and then into the square opening in the key chain.
• Snap the knobs into the knob
plate. Note: Gently squeeze the tabs on
the knobs together before insert­ing the knobs into the knob plate.
• Set the dashboard plate and
knob plate aside.
2
• Fit the phone holder into the pocket in the dash, as shown.
• Slide the tab on the front of the phone holder clip into the slot in the bottom of the phone holder to secure the phone holder to the dash.
• Insert a #6 x 1'' screw through the top of the phone holder and the dash, and into the screw peg on the back of the phone holder clip, as shown.
Helpful Hint: Press on the screw peg to align it with the screw holes in the phone holder and dash.
• Tighten the screw with a Phillips screwdriver. Do not over-tighten.
3
Square Opening
Key
Key Chain
#6 x 1" Screw
Shown Actual Size
Dash
Phone Holder
Phone Clip Holder
Tab
18
COOL
HEAT
TM
Key Chain
20
21
12
Assembly
• Open the phone’s battery compartment door and remove the packet of #3 x 3/8" screws.
• Insert three “AAA” (LR03) alkaline batteries as indicated in the battery compartment.
• Close the battery compartment door.
• Insert the #3 x 3/8" screws into the holes in the battery compartment door and tighten the screws with a Phillips screwdriver. Do not over-tighten.
4
“AAA” (LR03) x 3
Shown Actual Size
WARNING
Placing the “AAA” (LR03) batteries in the phone with the positive (+) and negative (-) markings the wrong way could cause damage or over-heating resulting in injury. The “AAA” (LR03) batteries must be positioned as shown on the battery compartment door.
Phone
Battery Compartment Door
Please Note:
• Do not mix old and new batteries.
• Do not mix different types of batteries; alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Remove batteries during long periods of non-use. Always remove exhausted batteries from this product. Battery leakage and corrosion can damage this product.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type, as recommended above, are to be recharged.
• If removable rechargeable batteries are used, they are only to be charged under adult supervision.
• Rechargeable batteries are to be removed from this product before they are charged.
• If you use a battery charger, it should be examined regularly for damage to the cord, plug, enclosure and other parts. Do not use a damaged battery charger until it has been properly repaired.
#3 x 3/8" Screw – 2
Shown Actual Size
+
13
Assembly
• Bend the end of the telephone cord so that it forms a “T”.
• Insert the end of the telephone cord through the hole in the dash, as shown.
• Pull up on the end of the telephone cord to be sure it is secure.
• Place the telephone in the telephone holder with the number pad facing out.
• Position the bottom edge of the knob plate in the opening in the dash.
• Snap the top of the knob plate into the dash.
1
2
3
4
5
6
7
8
Dash
5
Knob Plate
Telephone Cord
• Fit the tabs on the dash into
the slots in the front of the vehicle body.
• Insert two #10 x 1" screws through
the holes closest to the front of the vehicle body and into the vehicle body .
• Insert two #10 x 1/2'' screws through
the holes closest to the seating area and into the holes in the vehicle body .
• Tighten each screw with a Phillips
screwdriver. Do not over-tighten.
2
1
1
2
3
4
5
6
7
8
Dash
Tab
6
Slots
Tab
#10 x 1" Screw – 2
Body
#10 x 1/2" Screw – 2
Both Shown Actual Size
12121
2
• Fit the dashboard plate on the dash. The notch in the large hole should be at the top.
• Insert four #8 x 3/4" screws as shown.
• Tighten each screw with a Phillips screwdriver. Do not over-tighten.
7
Steering Column
• Wipe the steering column with a paper towel to remove any excess lubricant.
• Turn the vehicle body on its side.
• Insert the straight end of the steering column up through the hole in the vehicle body wall and out through the hole in the dashboard plate.
14
Dash
Dashboard Plate
Assembly
#8 x 3/4" Screw – 4
Shown Actual Size
Hole
8
Large Hole
Bottom View
Notch
10
• Turn the vehicle body upright.
• Position the steering wheel so that the spokes form a “Y” as shown. The tab on the steering wheel stem should face up.
• Fit the steering wheel onto the steering column.
• Fit a cap nut onto the end of the steering column.
• Tap the cap nut with a hammer to secure it on the steering column.
Helpful Hint! You may want the help of another person to support the steering column while you tap the cap nut with the hammer.
15
Steering Wheel
Cap Nut
Assembly
Steering Column
• Insert the end of the steering column through the hole in the steering rod.
• Fit a cap nut onto the end of the steering column.
• While supporting the steering column, tap the cap nut with a hammer to secure it on the steering column.
Helpful Hint! You may want the help of another person to support the steering column while you tap the cap nut with the hammer.
9
Steering Rod
Cap Nut
End of Steering Column
Bottom View
“UP”
Tab
TM
Loading...
+ 33 hidden pages