Fisher-Price 76922 User Manual

Owner’s Manual with Assembly Instructions

Please read this manual and save it with your original sale’s receipt.

For Model 76922

Tools needed for assembly:Phillips Screwdriver, Hammer, and Slotted Screwdriver (not included).

Use only with a Power Wheels®6 Volt (4.0 Amp/Hr.) Battery, Power Wheels®25 Amp Fuse

and Power Wheels®6 Volt (4.0 Amp/Hr.) Charger (all included).

Product features may vary from the picture above.

Songbird

ATV

Fisher-Price, Power Wheels by Fisher-Price and BARBIE are U.S. trademarks of Mattel, Inc.

Table of Contents

Important Information

A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

D Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

E Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

F Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

G Label Decoration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

H Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

I Battery Care and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

J Car ing For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

K Rules For Safe Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

L How to Operate Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

M Problems and Solutions Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

N Statement of Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

O Authorized Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

• Your new vehicle requires adult assembly. Please set aside at least 45 minutes for assembly.

• You must charge your battery for 18 - 30 hours before you use your vehicle for the first time.We recommend that you start charging your battery before beginning assembly. Please see Battery Charging beginning on page 6 for detailed instructions.

• Read this manual carefully for important safety infor mation and operating instructions before using your vehicle. Please keep this manual for future reference as it contains important information.

• This vehicle is designed for use: on grass, asphalt and other hard surfaces; on generally level terrain; and by children 12 - 36 months of age.

• Make sure children know and follow these rules for safe driving and riding:

- always sit on the seat.

- always wear shoes.

- only 1 (one) rider at a time.

• To prevent damaging the motors and gears, do not tow anything behind the vehicle or overload it. Do not exceed the maximum weight capacity of 40 lb.(18 kg).

• If you have any questions about your Power Wheels

vehicle, please call our toll-free service lines at 1-800-348-0751 from 8 AM to 6 PM (EST) Monday through Friday.Trained customer ser vice representatives are available to take your call in English or French.Habla Español? Si usted tiene alguna pregunta ó necesita asistencia llame gratis 1-800-348-0755 para los Estados Unidos.Tenemos representantes que hablan español para atender su llamada.

• For your convenience, Power Wheels®maintains an Authorized Service Center Network with more than 400 authorized service centers nationwide. Our authorized service centers will repair or replace parts under warranty at no extra charge, and can perform non-warranty repairs for a minimal charge.Please see the Authorized Service Center list beginning on page 22 to find the authorized service center nearest you, or call 1-800-348-0751.

• Please complete and return the enclosed Registration Card today, or call 1-800-348-0751 to register your vehicle by phone.

CA UTION

• In the unassembled state, this package contains small parts. Adult assembly is required.

• Use the charger in dry locations only.

WARNING

• Prevent Injuries and Deaths

• Direct Adult Supervision Required

• Keep Children Within Safe Riding Areas. These areas must be:

- away from swimming pools and other bodies of water to prevent drownings

- generally level to prevent tipovers

- away from steps, driveways, roads and alleys.

RIDING HAZARD

WARNING

• Batteries can fall out and injure a child if vehicle tips over. Always use battery clamp.

• PREVENT FIRE

- Do not bypass a Power Wheels®fuse. It is a safety device.

- Use only a Power Wheels

25 Amp fuse.

- Never modify the electrical system.Alterations could cause a fire resulting in serious injur y

and could also ruin the electrical system.

- Use of the wrong type battery, fuse or charger could cause a fire or explosion resulting in

serious injury.

- Use of Power Wheels

components in products other than Power Wheels®vehicles could

cause overheating, fire or explosion.

• The battery must be handled by adults only.The batter y is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in serious injur y.

• Never allow children to charge the batter y. Batter y charging must be done by adults only. A child could be injured by the electricity involved in charging the batter y.

• Never lift or carry the battery by the wires or connector. This can damage the battery and possibly cause a fire resulting in serious injury. Lift and carr y the batter y by the case only.

• Read the safety instructions on the battery.

• Examine the battery, charger and their connectors for excessive wear or damage each time you charge the battery. If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.

• HOT motors. Handle carefully.

Warnings and Cautions

ELECTRICAL HAZARD

Footrest

Handlebar Wire Harness

Handgrip - 2

Steering Column

Bushing

Wheel Bushing - 2

Cap Nut - 4*

Washer - 2

25 Amp Fuse - 1*

Round Bushing - 2

#8 x

/4" Screw - 3#10 x

" Screw - 2

All Shown Actual Size

Not Shown: Label Sheet

*For your convenience, an extra cap nut and an extra 25 amp fuse are included.

Vehicle Body

Front Wheel - 2

6 V olt Battery

6 Volt Battery Charger

Steering Column

Steering Linkage

Handlebar

Grille

Seat

Parts

• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store.

• Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.

• Metal parts have been coated with a lubricant to protect them during shipment.Wipe all metal parts with a paper towel to remove any excess lubricant.

IMPORTANT! Some parts were placed under the seat for shipment. Unlock the seat lock fastener, using a slotted screwdriver to rotate the lock fastener 1/4turn to the unlocked position . Lift the seat to access the battery compar tment.

Handgrip Streamer - 2

1. Vehicle Body

2. Steering Column

3. Handlebar

4. Handgrip - 2

5. Steering Column Bushing

6. Cap Nut - 4

7. 6 Volt Battery (4.0 Amp/Hr.)

8. Charger

9. Footrest

10. Seat

11. Handlebar Wire Harness

12. Battery Clamp

13. Grille

14. #10 x 7/8" Screw - 2

15. #8 x 3/4" Screw - 3

16. Steer ing Linkage

17. Washer - 2

18. Wheel Bushing - 2

19. Round Bushing - 2

20. Front Wheel - 2

21. 25 Amp Fuse

22. Handgrip Streamer - 2

Not Shown: Label Sheet

Parts Diagram

Note: Some parts shown are assembled on both sides of the vehicle.

CA UTION

Use the charger in dry locations only.

WARNING

Battery Charging

• Battery can fall out and injure a child if vehicle tips over. Always use battery clamp.

• PREVENT FIRE

- Do not bypass a Power Wheels

fuse.

It is a safety device.

- Use only a Power Wheels®25 Amp fuse.

- Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also r uin the electrical system.

- Use of the wrong type battery, fuse or charger could cause a fire or explosion resulting in serious injury.

- Use of Power Wheels

components in

products other than Power Wheels

vehicles could cause overheating, fire or explosion.

• The battery must be handled by adults only.The battery is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in serious injury.

• Never allow children to charge the batter y. Battery charging must be done by adults only. A child could be injured by the electricity involved in charging the battery.

• Never lift or carry the battery by the wires or connector.This can damage the battery and possibly cause a fire resulting in serious injury.Lift and carry the batter y by the case only.

• Read the safety instructions on the battery.

• HOT motors. Handle carefully.

Important Notes

• Your new battery must be charged for at least 18 hours before you use it in your vehicle for the first time.

• We recommend that you start charging your battery before beginning assembly of your new vehicle.

• The battery must be upright while charging.

• The charger is not a toy.

• Do not short circuit the battery.

• The battery must be removed from your vehicle for the initial charge in order to complete assembly.You do not need to remove the battery from your vehicle to recharge it.

• Before charging the battery, examine the battery case for cracks and other damage which may cause sulfuric acid (electrolyte) to leak during the charging process. If damage is detected, do not charge the battery or use it in your vehicle.Battery acid is very corrosive and can cause severe damage to surfaces it contacts.

• Do not charge the battery on a surface which could be damaged by the acid contained inside the battery. Take precautions to protect the surface on which you charge your battery.

• Use only a Power Wheels®6 volt charger (4.0 Amp/Hr.) and 25 Amp fuse to charge your Power Wheels

rechargeable 6 volt battery (4.0 Amp/Hr.).

• If your battery is old and will not accept a full charge, do not leave it in the vehicle. Always remove a dead battery from the vehicle.

ELECTRICAL HAZARD

• Insert a 25 amp fuse into the batter y. Note: The top of the fuse will not be flush with the top of the

battery when properly installed.

• Plug the charger connector into the battery connector.

• Plug the charger into a standard 120 volt wall outlet. Note: If power flow to the wall outlet is controlled by a

switch, make sure the switch is “ON”.

• Before first time use, charge the battery for at least

18 hours. Never charge the battery longer than 30 hours.

• Recharge the battery for at least 14 hours after each use of your vehicle.Do not charge the battery longer than 30 hours.

• Once the battery is charged, disconnect the charger connector from the battery connector.Unplug the charger from the wall outlet.The battery is now charged and is ready to be installed in your vehicle.Please see "Battery Installation" on page 14 for detailed battery installation instructions.

Battery Connector

Battery Clamp

Charger Connector

25 Amp Fuse

Charger

Battery Charging

IMPORTANT! The batter y must be removed from your vehicle for the initial charge in order to complete assembly. You do not need to remove the battery from your vehicle to recharge it.

• Using a Phillips screwdriver, loosen the screws in the battery clamp. Remove the battery clamp from the vehicle body.

• Remove the Power Wheels

6 Volt (4.0 Amp/Hr.) battery

from the battery compartment.

Wheel Bushing

• Fit a washer onto one end of the front axle.

• Slide the front wheel, bushing side first, onto the front axle.

• Turn the vehicle body upside down.

• Fit the steering linkage onto the fork on the front of the vehicle body. Make sure the center axle is toward the rear of the vehicle.

Front Wheel

Front Axle

Washer

Wheel Bushing

Fork

Steering Linkage

Center Axle

Vehicle Body

Assembly

• Turn the front wheels over.

• Fit a wheel bushing into the rectangular opening in each front wheel.

• Apply label #2 to the recessed circle on each front wheel, as shown. Please see “Label Decoration” on page 13 for application guidelines.

IMPORTANT! Some parts were placed under the seat for shipment. Unlock the seat lock fastener, using a slotted screwdriver to rotate the lock fastener

/4turn to the unlocked position .

Lift the seat to access the battery compartment.

Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle.

WARNING

• Slide a round bushing onto the front axle and press it into the center of the front wheel.

• Fit a cap nut onto the end of the front axle.

• Tap the cap nut with a hammer to secure it on the front axle.

• Repeat assembly steps 4 and 5 to assemble the other front wheel to the other side of the front axle.

Cap Nut

Front Axle

Round Bushing

• Insert the connector end of the handlebar wire harness into the rectangular opening in the handlebar.

• Feed the handlebar wire harness through the handlebar.

• Push firmly on the button end of the handlebar wire harness to snap it into the rectangular opening.

Rectangular Opening

Handlebar

Button End

Connector End

Handlebar Wire Harness

Handlebar

• Turn the handlebar upside down.

• Align the handlebar wire harness with the guides on the underside of the handlebar.

• Push firmly on the handlebar wire harness near each of the guides to secure the wire in the underside of the handlebar.

Guides

Assembly

Handgrip

Handgrip Streamer

• Using the tip of a slotted screwdriver, press the metal retainer on a handgrip streamer into the hole in a handgrip, as shown.

• Repeat this procedure to attach the other handgrip streamer to the other handgrip.

+ 18 hidden pages