Fisher-Price 71644 Instruction Sheet
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Model Number: 71644
For proper set-up and use,please read these instructions.
Please keep this instruction sheet for future reference,
as it contains important information.
Transmitter is electrically powered.
Crib soother is powered by three “D” alkaline batteries (not included).
Remote control receiver is powered by the AC adaptor (included, plugs
into standard household outlets 120V AC). Remote control receiver
also runs on battery power (9V alkaline battery - not included).
Adult assembly is required.
Tool needed for assembly: Phillips screwdriver.
Calming Vibrations
Monitor
2
This product cannot replace
responsible adult supervision.
CAUTION
IMPORTANT!
• This product is not intended to be used as a medical monitor
and its use should not replace adult supervision.
• Test sound reception of remote control receiver before first-time
use and whenever you change location of transmitter.
• To prevent entanglement:
- Never place transmitter in a crib or playpen. Keep transmitter
and remote control receiver out of baby’s reach.
- Never use extension cords with the AC adaptor.
• Never use transmitter, crib soother or remote control receiver near
water (ie.: bathtub, sink,laundry tub or wet basement, etc.).
• Always use transmitter, crib soother and remote control receiver
where there is adequate ventilation.To prevent overheating, keep
transmitter, crib soother and remote control receiver away from
heat sources such as radiators, heat registers, direct sunlight, stoves,
amplifiers, or other appliances which produce heat.
• Never attempt to modify this product.
• Always be sure the transmitter channel switch is set to the same
channel as the remote control receiver.
Calming Vibrations Monitor
3
Listen and respond to baby with calming vibrations and sounds.
Transmitter Crib Soother
Remote Control
Receiver
Transmitter
Place in baby’s room or play area to transmit sounds to the remote control
receiver. Transmitter operates on AC current.
Remote Control Receiver
Listen and respond to baby from anywhere around the home.Remote
control receiver operates using the AC adaptor (included) or battery power.
Crib Soother
Attach to baby’s crib and select calming vibrations, sea shore sounds
or both! Activate by pressing the soothing button on the remote control
receiver, transmitter or the crib soother. Requires three “D” (LR20) alkaline
batteries for operation.
IMPORTANT! Make sure the transmitter channel switch is set to the same
channel switch as the remote control receiver.
4
Occasionally a consumer may experience a problem with one of our
products. If this should happen, please call us toll-free, rather than
return this product to the store. Usually, we can solve the problem
over the telephone or send you replacement parts.
Please call Fisher-Price® Consumer Relations, toll-free at
1-800-432-5437, between 8 AM - 6 PM EST, Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
Consumer Information
If you have any questions about this product:
In Canada, call 1-800-567-7724,or write to: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2.
In Great Britain, telephone 01628 500302.
In Australia, Mattel Australia Pty.Ltd.,658 Church Street,Locked Bag #870,
Richmond,Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812
(valid only in Australia).
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
Assembly
5
Crib Soother Slot
Bolt
Lock Nut
(Rounded Side Out)
M4 x 1" Screw
M4 Lock Nut
Rounded Side
BOTH SHOWN ACTUAL SIZE
• Fit the bolt into the slot on the
back of the crib soother.
• Insert the screw into the hole in
the crib soother,as shown.
• Fit the lock nut, rounded side out,
into the hexagonal opening on
the crib soother,as shown.
• Tighten the screw with a Phillips screwdriver. Do not over-tighten.
Remote Control Receiver
Battery Installation (Optional)
6
• Locate the battery compartment door on the back of the remote
control receiver.
• Loosen the screw in the battery compartment door with a Phillips screwdriver.Lift to remove the battery compartment door.
• Snap the terminals of a fresh, 9V alkaline battery into the remote control
receiver connectors.
• Replace the battery compartment door and tighten the screw with a
Phillips screwdriver. Do not over-tighten.
Battery
Compartment Door
9V (6LR61)
Shown Actual Size
The remote control receiver operates using
the enclosed AC adaptor or battery power.
Crib Soother Battery Installation
7
• Locate the battery compartment door on the back of
the crib soother.
• Loosen the screws in the
battery compartment door
with a Phillips screwdriver.
Lift to remove the battery
compartment door.
• Insert three “D” alkaline batteries as indicated inside the
battery compartment.
• Replace the battery compartment door and tighten the screws with a
Phillips screwdriver. Do not over-tighten.
1.5V x 3
“D” (LR20)
Shown Actual Size
+
-
Battery
Compartment Door
Hint: When battery power is too low,vibrations/sounds may not shut off or
may not function properly as described in these instructions. Remove and replace
all three batteries with three, new “D”(LR20) alkaline batteries.
Battery Tips
• Remove the batteries during long periods of non-use. Always remove
exhausted batteries from the product. Battery leakage and corrosion
can damage this product. Dispose of batteries safely.
• Do not dispose of the batteries in a fire.The batteries may explode
or leak.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the
“Battery Installation” instructions are to be used.
• If a removable rechargeable batteries are used, they are only to be
charged under adult supervision.
• Rechargeable batteries are to be removed from the product before
they are charged.
• If you use a battery charger,it should be examined regularly for
damage to the cord, plug, enclosure and other parts. Do not use
a damaged battery charger until it has been properly repaired.
• We recommend the use of alkaline batteries for longer battery life.
8
Loading...