Fisher-Price 71599 User Manual
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Model Number: 71599
For proper setup and use,please read these instructions.
Please keep this instruction sheet for future reference,
as it contains important information.
Transmitter is electrically powered.
Includes one AC adaptor to power receiver (plugs into
standard household outlets –120V AC). Receiver also runs on battery
power (3.6V, 400mAH nickel cadmium rechargeable battery – included).
Adult assembly is required to install the battery.
Tool needed for battery installation:
Phillips screwdriver (not included).
Vibrating
Monitor
This product cannot replace
responsible adult supervision.
CAUTION
IMPORTANT!
2
• This product is not intended to be used as a medical monitor
and its use should not replace adult supervision.
• Test reception of receiver before first-time use and whenever you
change location of transmitter.
• To prevent entanglement:
- Never place transmitter in a crib or playpen. Keep transmitter
and receiver out of baby’s reach.
- Never use extension cords with the AC adaptor or the transmitter
power cord.
• Never use transmitter or receiver near water (ie.:bathtub, sink,
laundry tub or wet basement, etc.).
• Always use transmitter and receiver where there is adequate
ventilation.To prevent overheating,keep transmitter and receiver
away from heat sources such as radiators,heat registers, direct sunlight, stoves, amplifiers, or other appliances which produce heat.
Receiver Battery Installation
3
Battery
Compartment Door
• Locate battery compartment door on back of receiver.
• Loosen screw in battery compartment door with a Phillips screwdriver.Remove battery compartment door.
• Plug battery connector into receiver connector.
• Replace battery compartment door.Tighten screw with a
Phillips screwdriver.
Battery Tips
• Remove the battery during long periods of non-use. Always
remove an exhausted battery from the product. Battery leakage
and corrosion can damage this product. Dispose of battery safely.
• Do not dispose of battery in a fire. The battery may explode or leak.
• Never short circuit the battery terminals.
• A non-rechargeable battery is not to be recharged.
• Only a battery of the same or equivalent type as recommended in
the “Battery Installation”instructions is to be used.
• If a removable rechargeable battery is used, it is only to be charged
under adult supervision.
• If you use a battery charger,it should be examined regularly for
damage to the cord, plug, enclosure and other parts. Do not use
a damaged battery charger until it has been properly repaired.
• Use only the provided AC adaptor to charge the battery.
Your Fisher-Price® Vibrating Monitor includes a rechargeable battery.
Before first-time use, you will need to charge the battery (see next page).
Hint: If battery connector will not plug into receiver connector,turn it over
and try again. Do not force the battery connector into the receiver connector.
Battery Connector
Receiver Connector
Charging the Receiver Battery
• Insert AC adaptor jack into receiver socket and then plug into
wall outlet.
• Charge the rechargeable battery for 10-12 hours. Do not overcharge
your battery.
Battery Disposal
Nickel cadmium batteries contain materials which are harmful to the
environment if not properly disposed.Contact the recycling center in
your community for proper disposal instructions.
Hint: When using the receiver with the AC adaptor,you will be charging
the battery while monitoring your baby!
4
Even with proper care,the rechargeable battery will not last forever.
The life of the rechargeable battery depends on how well you follow
these instructions and the total number of hours it is used. If you
should need to replace the rechargeable battery, a new one can
be purchased at most electronics stores or contact Fisher-Price®
Consumer Relations at 1-800-432-KIDS.
Testing Reception (for Sound)
5
Test transmitter transmission and receiver reception
each time you change location of use.
Place transmitter in room in which
you intend to use it. Rotate transmitter
power switch to turn power on.Power
indicator lights.Turn on a radio.
Place receiver in room in which
you intend to use it. Rotate the
power/volume dial to turn power
on. Power indicator lights. Adjust
receiver location.
• Variable light display lights when
sound is received by receiver:
- One two dots light for
shallow sounds.
- Three or more dots light for
louder sounds.
If you experience interference
(buzzing or static, etc.) while using
one channel setting, switch both
units to other channel. Selecting
a channel is usually a one time
adjustment.
Hint: All five dots in receiver variable light display light:
- If you turn receiver power on before transmitter power.You will also hear
static noise.Turn volume down on receiver and turn transmitter power on.
- If the receiver is too far away from the transmitter.Move the receiver closer
to the transmitter.
- If loud sounds are transmitting.
Adjust
Channel
BUZZZZ
STATIC
Power
Indicator
Power
Switch
Power
Indicator
Power/Volume
Dial
Loading...