Fisher & Paykel excellence GWL12, GWM12, GWC12, MWC12, excellence GWM12 Installation Instructions And User Manual

...

New Zealand Australia USA Canada Europe Asia Pacific

GWL12, GWM12, GWC12, MWC12

Installation instructions and

User guide

Clothes Washer

Intelligence Working For You

70 years of laundry experience has led to the development of the world’s most advanced wash system, the Smart Drive™.

Unlike conventional machines, Smart Drive™ autowashers use intelligence to adapt the wash action and water levels to save on water and electricity use; making it kinder on your wallet and the environment.

Intelligent Electronics

A powerful microprocessor controls every aspect of the Smart Drive™, allowing it to continually monitor and respond to each wash. It contains over 10,000 lines of instructions in its brain’ – the result of many years of testing and fine-tuning, to give you the best possible performance.

Direct Drive Motor

Our revolutionary direct drive motor is capable of infinite wash actions, continuously adjusting its speed to the movement of your clothes, removing dirt while caring for the fabric, delivering the ultimate wash.

Reliability

The Smart Drive™ has no mechanical brake, pulleys or gears, which means fewer moving parts and greater reliability.

Saves Time

With a top spin speed of 1000rpm, Smart Drive™ reduces clothes drying time by up to 30%.

Energy Conservation

The unique wash action means a typical load uses only the same amount of electricity as a 100-watt light bulb left on for an hour.

Eco

Designed to make every drop count, using up to 25% less water than the traditional Water Saver rinse.

Contents

Installation Instructions

Specifications 8

Getting Started

Before You do Your First Wash 9 Using Your Excellence Washer 10 Using Your Pride Washer 12

Lidlock

Wash Cycles and Options

The Wash Cycle and Options 15 Selecting the Wash Options and Advancing the Cycle 16 Water Levels 17 Saving Water – Eco, Water Saver 18 Soak, Spin Hold, Delay Start 19 Washing Bulky Items, Washing Woollens 20 Favourite Cycle 21 Customising the Wash Cycle 22

Before You Wash

Sorting, Loading 23 Detergent 24 Fabric Softener, Scrud 25

Changing Pre-set Options

Option Adjustment Mode 26 Wash Temperatures, Rinse Options 28 Controlled Cold, End of Cycle Beeps, Water Saver, Auto Water Fill Level 29 Out of Balance Recovery Routine 30

Machine Information

Cleaning Your Smart Drive™ 31 Products That Might Damage Your Smart Drive™ 32 Smart Drive™ Sounds and Beeps, Automatic Lint System 32

Problem Solving

If Your Smart Drive™ Beeps for Help 33 Operating Problems 35 Wash Problems 36

Please Note:

All diagrams feature the EXCELLENCE button shape unless otherwise stated. The use of the button is the same for all Smart Drive™ models.

Installation Instructions

Unpacking

To ensure the best performance from your new Smart Drive™ please follow the instructions below.

Removing the Packaging

Remove the outer packaging.

Tilt the machine backwards and walk it off the bottom packer one foot at a time.

Remove the bottom packer from under the machine by pulling it out the front.

Lift the lid and remove the bowl packer from the bowl.

Remove the hoses and accessories.

Keep the bottom packer and bowl packer in case they are required for future transit.

Please ensure that the bottom packer has been removed before operating your machine.

In your autowasher you will find:

■

4 rubber inserts for the levelling feet (joined together).

■

1 hose guide.

■

White inlet hose.

Inlet Hose

Connect the straight ends of the white inlet hose to the tap. There are washers fitted in both ends.

Connect the elbow end of the white inlet hose to the machine inlet valve. Inlet valves are marked on the back of the machine

H=Hot C=Cold.

Cold Supply Only:

If you only have a cold water supply, an inlet valve cap (blanking cap) MUST be connected to the hot inlet valve. The cap prevents water leaking out of the hot valve. If you select any of the warm or hot settings, the machine will come up with a user alarm (refer to “If Your Smart Drive™ Beeps for Help”, page 33) as there is no hot water to maintain the temperature you have selected.

Note:

The Smart Drive™ does not have an internal heater to heat the water.

Inlet valve cap

Machine end

Tap end

Installation Instructions

Drain Hose

Carefully pull the black drain hose out from the back

of the machine by pulling the exposed part of the hose downwards and outwards.

The drain hose can be:

■

Connected to a standpipe.

■

Connected to a tub.

■

Connected to a floor drain using an antisyphon vent

pipe (not supplied).

When connecting the drain hose to a tub or

standpipe, use the hose guide, included in the accessory kit, to guide the drain hose over the tub or into the standpipe. The drain hose should not extend more than 20mm from the end of the guide (this is to prevent syphoning). If necessary the drain hose can be trimmed to length.

When connecting to a floor drain we recommend

using an antisyphon vent pipe. This is a short standpipe (400mm long and 40mm in diameter) attached to the back of the machine.

A flexible hose connects it to the floor drain.

Note:

Use an adhesive to attach the vent pipe to the back of the machine. Do not use screws as they may damage internal parts.

Make sure the top of the vent pipe is level with the

drain hose outlet.

Syphoning may occur if the drain hose is positioned too low or connected directly to a floor drain. This may result in a user warning (refer page 33).

Drain hose connected to a standpipe

Drain hose connected to a floor drain using an antisyphon vent pipe

Accessories and Spare Parts

Available from your Fisher & Paykel Dealer or Authorised Service Centre.

Hose Inlet Long (2m) Part No. 422680

Hose Inlet Large Bore Part No. 426123

Drain Hose Extension Part No. 425627p

Power Cord If the Power Cord of your autowasher is damaged it must be

replaced by a Fisher & Paykel Authorised Service Centre, as it is not a standard power cord.

Vent pipe to be level with hose outlet

850 – 1200mm

400mm

Installation Instructions

Levelling

It is IMPORTANT to level the machine to ensure even spin performance.

Separate the 4 rubber foot inserts from the moulding and fit into the feet on the base of the machine.

Move the machine to its final position. (We suggest a minimum clearance of 20mm each side).

Adjust the feet so the machine is level and cannot rock.

To Check if Your Machine is Level:

Look down on the wash bowl and make sure it sits slightly forward of centre (see diagram).

Close the lid. Visually check that the lid fits

evenly on both sides.

If it does not look like the diagram in the middle, adjust one of the front feet slightly until it matches. The diagram on the top and bottom are not correct.

Turn on the water and check all hose connections for leaks. Make sure there are no kinks in

the hose.

Uncoil power cord and plug into wall socket.

Lid Alignment

Lid

Topd ec k

Wind left foot down (out) to correct

Wind right foot down (out) to correct

Adjustable feet

Rubber insert

Correct

Incorrect

To check levelling look down on the wash bowl

Installation Instructions

Earthing

Earthed Plugs

(Power cord with 3 pin plug) Plug into a compatible 3 pin wall socket.

Non–Earthed Plugs

(Power cord with 2 pin plug and a separate earth wire)

This appliance MUST be earthed using the earth wire attached to the rear of the machine. The

exposed end of the earth wire must be in contact with an earth point eg in contact with an earthing bar, metal water pipe.

Improper earthing of this machine can result in a risk of electric shock. Check with a qualified

electrician or serviceman if you are in doubt as to whether the machine is properly earthed. (Refer to page 8).

Water Supply

■

For best operating conditions your hot water should be approximately 65˚C. Your cold water

should not exceed 35˚C or your hot water exceed 75˚C. Temperatures above this may cause the machine to fault or cause damage to the machine.

■

If you have an uncontrolled water heating source (eg a wet back or solar heating system) you

should fit a Safe Valve. This will ensure the hot water temperature remains within safe limits.

Draining

■

Regularly check that your standpipe or tub is free from lint or other obstructions, as this may

affect how your machine works.

■

In multi-storey apartments or any upper floor, the machine should be installed on a drained floor.

■

Draining must comply with local by-laws.

Autowasher Safety

■

This autowasher is not intended for use by young children or infirm persons without supervision.

■

Connection to the water mains must be with new hoses and the old hoses must be discarded.

■

Your Smart Drive™ can be opened while it is filling and agitating, supervise young children to

ensure they do not play with it.

CAUTION!

If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet box), ensure that it is positioned so that it does not come into contact with water or moisture.

Installation Instructions

Specifications

(Please note these are approximate figures for High water levels.)

Water Consumption

Total Water Consumption for the Different Rinse Options

Model

Water Saver

(excellence models)

Eco Option

Spray &

Deep Rinse

1 Deep

Rinse

2 Deep

Rinses

GWL12 150 L 105 L 180 L 155 L 205 L

GWM12 130 L 90 L 165 L 140 L 185 L

GWC12 110 L 76.5 L 145 L 120 L 155 L

MWC12 – 76.5 L 145 L 120 L 155 L

Inlet water pressure Max 1MPa (150 psi) Min 34kPa ( 5 psi)

1020– 1050mm

Height to top of console

Large 650mm

Medium 600mm

Compact 560mm

Height with Lid Open

Large 1410–1440mm

Medium 1360–1390mm

Compact 1320– 1350mm

Large 650mm

Medium 600mm

Compact 560mm

Cold

Minimum height of taps

to clear the top of machine

1150mm

850– 1200mm

Standpipe

Thank you for buying a Fisher & Paykel Smart Drive™ washing machine. We are very proud of this washer and trust it will serve you well for many years.

At Fisher & Paykel we aim to provide innovative products that are simple to use, ergonomic and energy efficient. Thousands of tonnes of washing and 70 years of laundry experience have been programmed into your washing machine to help give you the best possible performance.

We hope you enjoy your new washing machine, we have certainly enjoyed designing it.

Before You Do Your First Wash

You owe it to yourself and your Smart Drive™ to have it installed correctly by an authorised service agent.

Before you start, it is a good idea to go through the following checklist:

Has the basepacker been removed?

Are all valves either connected to an inlet hose or blanking cap? Is the cold hose connected to

the cold valve marked ‘C’?

Is the drain hose threaded through the ‘U bend‘ (with no more than 20mm extended) and on to

your standpipe?

Are the rubber inserts secured into the feet on the base of your machine and is the machine

levelled?

Refer to Installation Instructions, page 4.

If you have bought a Pride model it is a good idea to check the warm fill temperature. (Refer to

page 28).

Using Your Excellence Washer

■

Remove fabric softener dispenser.

■

Place the load evenly around the agitator. (Refer to Sorting and Loading page 23).

A. Detergent

■

Use the mark on the agitator, nearest to the top

of the clothes, as a guide to the correct amount of detergent to use.

■

Pour the detergent down the centre of the

agitator stem. Replace the fabric softener dispenser (this stops small articles falling down the centre of the agitator). (Refer to Detergent page 24).

B. Fabric Softener

■

If you wish to use fabric softener, place it in the

dispenser on the top of the agitator.

■

Fabric softener must not be used if you have

selected the Water Saver or Eco option.

(Refer to Fabric Softener page 25).

C. Power Button

■

Press POWER to turn the machine on.

D. Select Wash Cycle

■

Press the desired wash cycle button.

E. Wash Options

■

Select the WASH TEMPERATURE and other wash options.

F. Start

■

Press START/PAUSE to start the machine.

If You Wish to Stop Your Smart Drive™ During the Cycle

■

Press START/PAUSE

■

If it is during spray rinse or spin there is a slight delay while the bowl is coasted to a stop and the

lid is unlocked.

For best fabric and colour care remove your clothes as soon as the cycle has finished.

Using Your Pride Washer

■

Remove fabric softener dispenser.

■

Place the load evenly around the agitator. (Refer to Sorting and Loading page 23).

A. Detergent

■

Use the mark on the agitator, nearest to the top

of the clothes, as a guide to the correct amount of detergent to use.

■

Pour the detergent down the centre of the

agitator stem. Replace the fabric softener dispenser (this stops small articles falling down the centre of the agitator). (Refer to Detergent page 24).

B. Fabric Softener

■

If you wish to use fabric softener, place it in the

dispenser on the top of the agitator.

■

Fabric softener must not be used if you have

selected the Eco option.

(Refer to Fabric Softener page 25).

C. Power Button

■

Press POWER to turn the machine on.

D. Select Wash Cycle

■

Select the cycle you want by pressing the Cycle Button located below the Regular option. Scroll

through the cycles until the one you want is lit.

E. Wash Options

■

Select the WASH TEMPERATURE and other wash options.

F. Start

■

Press START/PAUSE to start the machine.

If You Wish to Stop Your Smart Drive™ During the Cycle

■

Press START/PAUSE

■

If it is during spray rinse or spin there is a slight delay while the bowl is coasted to a stop and the

lid is unlocked.

For best fabric and colour care remove your clothes as soon as the cycle has finished.

Lidlock

Your Smart Drive™ has a lidlock, which locks when your machine is spinning. This ensures the lid cannot be opened during hazardous parts of the cycle, providing added safety for you and your family.

The lidlock light (above the START/PAUSE button) comes on when the lid is locked to tell you when you cannot open the lid. In short it means you can open the lid while your Smart Drive™ is filling, agitating, and draining, but not while it is spinning.

■

When the Lidlock light is on, the lid is locked.

■

When the Lidlock light is off, the lid is not locked and the lid can be opened.

■

If the Lidlock light is flashing the Lidlock is in the process of locking or unlocking, (i.e. while the

machine coasts down or START/PAUSE has been pressed). During this stage the lid still cannot be lifted.

If the lid is left open, the machine will be unable to lock and the cycle will be halted. The machine will play a tune and the lidlock light will flash until the lid is closed and START/PAUSE is pressed.

The lidlock remains unlocked for the majority of the cycle allowing you to add clothes, dissolve detergent or to add fabric softener (if you do not want to use the Automatic Fabric Softener Dispenser).

The chart below shows the stages when the lid is locked.

Fill Unlocked

Agitate Unlocked

Spray Rinse Locked

Deep Rinse Unlocked

Spin Locked

Keep children away from the machine, especially when you are using hot water, as the lid can be opened during fill and agitate.

DO NOT put anything down the slot in the top deck of your machine. DO NOT try to disable the lidlock.

The Wash Cycles

*Approximate times (minutes) for a high water level load on EXCELLENCE models.

Cycle times are dependent on your household water pressure.

Model Variations

EXCELLENCE

models - Fully featured, with all 5 wash cycles and a favourite cycle.

PRIDE

models - Regular, Heavy Duty, Delicate and Wool cycles.

■

Regular

cycle (with the Eco option) has been designed for normally soiled, everyday washing

eg sheets, towels, T-shirts.

■

Heavy Duty

cycle is for heavily soiled durable garments eg overalls, jeans, tea towels.

■

Delicate

cycle uses a slow, gentle agitation designed to care for your most delicate garments

eg lingerie, blouses.

■

Permanent Press

cycle is for garments that crease easily eg business shirts.

■

Wool

cycle is for machine washable woollens.

Regular Heavy duty Delicate

Permanent

Press

Wool

Wash Time

12 min 15 min 6 min 9 min 6 min

Wash Action

Regular Heavy Duty Delicate Regular Delicate

Wash Temp

Cold Cold Cold Cold Cold

Rinse

deep rinses2 deep rinses2 deep rinses2deep rinses2 deep rinses

Spin Speed

Fast Fast Slow Slow Medium

Spin Time

6 min 6 min 4 min 2 min 6 min

Cycle Times*

Large

50 53 42 43 42

Medium

47 50 38 39 39

Compact

43 46 34 34 34

Wash Options and Advancing the Cycle

To Select the Wash Options

Model

Select the wash cycle, temperature, water level and

spin speed. (Refer to Page 11).

Press the OPTIONS button if you want to choose

Eco, Soak or Water Saver. (Refer to pages 18 and 19).

Press START/PAUSE.

Model

Select the wash cycle, temperature, water level and

spin speed. (Refer to Page 13).

If you wish to save water press the Eco button.

(Refer to page 18).

Press START/PAUSE.

The Wash Progress Lights

The Wash Progress lights show all the tasks your Smart Drive™ will do during the wash cycle. As each task is completed a light goes out, so you can tell at a glance how far the cycle has to go.

Note:

Two lights are used to show warm–hot and warm–cold wash temperatures.

To Advance the Wash Cycle

Press POWER.

Press the button with the “two arrows” repeatedly to advance the cycle, to the desired position.

Press START/PAUSE.

Note:

Each wash progress light equals 3 minutes of agitation. The Eco option wash progress lights may in some cases wash for longer. This is dependent on the water level.

Clothes Care Safeguards

To avoid accidentally damaging your clothes there are a few options that your Smart Drive™ will not accept. For example, you cannot select a hot wash on Delicate, Permanent Press or Wool cycles.

Water Levels

Manual Water Level Selection

The agitator has 5 levels marked on its stem that can be used to help you select the correct water level. Select the correct water level by using the mark nearest to the top of the load.

■

The levels marked on the agitator do not correspond

exactly to the level of the water. They indicate the level of dry clothes suitable for the water level.

■

Your Smart Drive™ may occasionally add water during

agitation. This is to maintain the water level due to the release of air trapped in the garments.

■

Out of balance loads, tangling or splash-over can be caused

by selecting a water level that is too high.

■

The medium/high and medium/low settings are available

on the Excellence models only.

Auto Water Level

Model Only

Your Smart Drive™ can automatically select the appropriate water level for the load.

Place your clothes in the machine.

Select the wash cycle (Select AUTO if not automatically selected).

Press START/PAUSE.

During fill the machine will pause occasionally to sense

the water level. The machine will check if the water level is correct by using a series of 2 different agitate strokes. A slow stroke to sense the load and an agitate stroke to mix the load. (This may take over a minute.) If it detects that the water level is not high enough, it will fill with more water and re-check the level.

■

When washing an unusual load, eg large bulky garments

or pillows, we recommend you manually select the water level and select the Delicate cycle.

■

Manually select the water level if there is already water in

the bowl.

Note:

If you feel the Auto Water Level does not fill to the correct level, you can adjust the level the machine selects. (Refer to Changing Pre-set options page 26 – 29).

Wash Options – Saving Water

Eco

& Models

Press the Eco option to save large amounts of water. The Eco option uses an Eco Spray rinse which has been specially designed to use 25% less water than the Water Saver option. Use this option when you want to use less detergent and less water. If you have low water

pressure or sensitive skin it is better to use the Water Saver option (Excellence model only).

The Eco option has not been designed to be used with fabric softener as it does not have a second deep rinse

to dispense the softener correctly.

Water Saver

Model Only

Our Excellence model provides an excellent opportunity to save on water. Use the Water Saver option when you want to minimise the amount of water used during a Regular or Heavy Duty wash cycle.

Press the Water Saver option to change the rinse from two Deep rinses to a Shower rinse. A Shower rinse alternatively showers the clothes with water and spins them to remove the sudsy water. (If you wish to save even more water select the Eco option).

The Water Saver option has not been designed to be used with fabric softener as it does not have a second deep rinse to dispense the softener correctly.

Note:

Water Saver and Eco options are only available on the Regular and Heavy Duty cycles. If you try to select these options on the Wool, Delicate or Permanent Press cycle, your Smart Drive™ will skip over the option. Water Saver and Eco will take slightly longer than two deep rinses.

There are some wash loads that may not suit being washed using either the `Eco´ or `Water Saver´ options. For instance, loads that have a lot of sand or sawdust in them or garments where the colour still runs from them.

Wash Options

Soak

Model Only

Use the Soak option to soak clothes at the end of the wash phase or when you wish to re-use the wash water.

When you select Soak your Smart Drive™ will soak for

a period of 1 hour before completing rinse and spin. During soak your Smart Drive™ will agitate for a few seconds every minute.

Nappy Sanitisers/ Bleach

Nappy sanitisers and bleach are very corrosive to metal surfaces. DO NOT use your Smart Drive™ to soak items

in bleach or sanitiser, or tip the contents of the nappy bucket into your machine. Rinse and wring items out

thoroughly before placing them in your machine.

Spin Hold

Use the Spin Hold option to:

■

Remove drip dry garments from a mixed load before the

wash goes into spin.

■

Minimise the clothes creasing when they are left to sit in

the bottom of the bowl at the end of the cycle.

When you have selected Spin Hold, your Smart Drive™

will pause at the end of rinse, beep and the spin light will flash to tell you that it is waiting for another instruction.

Press START/PAUSE to begin the spin.

Delay Start

Model Only

Delay Start will delay the start of the wash cycle for 1, 3 or 9 hours.

Press DELAY START once for a delay of 1 hour. Press again for 3

hours, a third time for 9 hours (and again to return to normal).

■

Once you press Delay Start your Smart Drive™ will begin the

delay period, you do not have to press START/PAUSE.

■

Be careful if using Delay Start for non-colourfast clothes as

dyes may run if the clothes are damp.

■

Your Smart Drive™ will not beep at the end of the cycle if Delay

Start is selected.

Wash Options

Washing Bulky Items

Forcing large items into the machine may result in

them being damaged during washing. Make sure there is enough room in the machine for items to move when being washed.

Some items float up during the wash, (eg duvets/

doonas and pillows). If they sit too high they may touch stationary parts of the machine during agitate or spin. To minimize the chance of this happening, bulky items

should be pushed down below the water level after fill and pushed to sit below the medium high water level mark on the agitator before spinning. Select a slow spin.

To prevent an out of balance load or splashover we

recommend washing these items on the Delicate cycle. If you wish to re-spin the load at a faster speed

make sure the load is sitting below the medium-high mark before spinning.

Washing Woollens

The Wool Cycle has been approved by the New Zealand Wool Board and the Australian Wool Corporation for Woolmark products carrying a MACHINE WASHABLE care claim. The fibres of these woollens have been treated to prevent felting when they are machine washed. Most handknitted garments are not made of machine washable wool and we recommend that you wash them by hand.

■

Check the care label.

■

Use a wool detergent.

■

Use the Wool cycle.

■

Hand washed woollens may be spun in your Smart Drive™.

■

To dry woollens lie them flat on a towel and pat into shape. Dry out of direct sunlight.

■

Some wool underlays and sheepskin products can be washed in a washing machine but may

produce excessive amounts of lint that may cause pump blockages.

Bulky items should sit below the medium high water level mark.

Favourite Cycle

Model Only

Favourite cycle lets you design the wash cycle. It can be any wash cycle with any of its wash options and it can start from any point in the cycle. For instance, it may be a cycle to wash your gym gear or it may be a rinse and spin to finish washing the nappies.

To Set Your Favourite Cycle

Press Power.

Press the FAVOURITE cycle button. Hold down for 2 seconds.

You will hear 2 quick beeps and the Favourite light will flash.

Select your favourite cycle, (eg Regular, Delicate).

Select the wash options, (eg cold wash, soak). Use ADVANCE if you want part of a cycle, (eg to rinse nappies).

Press FAVOURITE again to store your favourite cycle.

To change your favourite cycle simply repeat these steps.

Note:

Your Smart Drive™ will remember your favourite cycle even when it is turned off at the wall. It is not possible to program a delayed start into the Favourite cycle.

To Use Favourite Cycle

Press POWER.

Press FAVOURITE. (Your favourite cycle and wash options will be automatically selected).

Press START/PAUSE.

Customising the Wash Cycles

To Customise A Wash Cycle

Model Only

You can program your Smart Drive™ to remember the wash options you prefer for each wash

cycle. For instance, you may want to set the Regular cycle to a cold wash or set Heavy Duty to include a soak.

Press POWER.

Press the wash cycle button. Hold down for 2 seconds.

You will hear 2 quick beeps and the wash cycle light will flash.

Select your wash options, (eg cold wash, soak).

Press the wash cycle again to store your customised cycle.

To change your customised wash cycle simply repeat these steps.

When you are customising a wash cycle you can shorten or lengthen the agitation time.

■

To shorten the agitation time, press ADVANCE to reduce the number of green lights.

■

To increase the agitation time keep pressing ADVANCE until all the green lights are on.

Note:

Unlike the Favourite cycle you cannot customise a wash cycle to start at the rinse or spin stage. On Heavy Duty and Wool you can only decrease the wash time.

+ 50 hidden pages

Fisher & Paykel excellence GWL12, GWM12, GWC12, MWC12, excellence GWM12 Installation Instructions And User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual