Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
650
Te c h n i c a l
The Details
NACE MR0175, “Sulde Stress Corrosion Cracking Resistant
Metallic Materials for Oil Field Equipment” is widely used
throughout the world. In late 2003, it became NACE MR0175/
ISO 15156, “Petroleum and Natural Gas Industries - Materials for
Use in H2S-Containing Environments in Oil and Gas Production.”
These standards specify the proper materials, heat treat conditions
and strength levels required to provide good service life in sour
gas and oil environments.
NACE International (formerly the National Association of
Corrosion Engineers) is a worldwide technical organization which
studies various aspects of corrosion and the damage that may
result in reneries, chemical plants, water systems and other types
of industrial equipment. MR0175 was rst issued in 1975, but the
origin of the document dates to 1959 when a group of engineers
in Western Canada pooled their experience in successful handling
of sour gas. The group organized as a NACE committee and in
1963 issued specication 1B163, “Recommendations of Materials
for Sour Service.” In 1965, NACE organized a nationwide
committee, which issued 1F166 in 1966 and MR0175 in 1975.
Revisions were issued on an annual basis as new materials and
processes were added. Revisions had to receive unanimous
approval from the responsible NACE committee.
In the mid-1990’s, the European Federation of Corrosion (EFC)
issued 2 reports closely related to MR0175; Publication 16,
“Guidelines on Materials Requirements for Carbon and Low Alloy
Steels for H2S-Containing Environments in Oil and Gas Production”
and Publication 17, “Corrosion Resistant Alloys for Oil and Gas
Production: Guidance on General Requirements and Test Methods
for H2S Service.” EFC is located in London, England.
The International Organization for Standardization (ISO) is a
worldwide federation of national standards bodies from more than
140 countries. One organization from each country acts as the
representative for all organizations in that country. The American
National Standards Institute (ANSI) is the USA representative
in ISO. Technical Committee 67, “Materials, Equipment and
Offshore Structures for Petroleum, Petrochemical and Natural Gas
Industries,” requested that NACE blend the different sour service
documents into a single global standard.
This task was completed in late 2003 and the document was
issued as ISO standard, NACE MR0175/ISO 15156. It is
now maintained by ISO/TC 67, Work Group 7, a 12-member
“Maintenance Panel” and a 40-member Oversight Committee
under combined NACE/ISO control. The three committees are an
international group of users, manufacturers and service providers.
Membership is approved by NACE and ISO based on technical
knowledge and experience. Terms are limited. Previously, some
members on the NACE Task Group had served for over 25 years.
NACE MR0175/ISO 15156 is published in 3 volumes.
Part 1: General Principles for Selection of Cracking-Resistant Materials
Part 2: Cracking-Resistant Carbon and Low Alloy Steels, and the
Use of Cast Irons
Part 3: Cracking-Resistant CRA’s (Corrosion-Resistant Alloys) and
Other Alloys
NACE MR0175/ISO 15156 applies only to petroleum production,
drilling, gathering and ow line equipment and eld processing
facilities to be used in H2S bearing hydrocarbon service. In the
past, MR0175 only addressed sulde stress cracking (SSC). In
NACE MR0175/ISO 15156, however, but both SSC and chloride
stress corrosion cracking (SCC) are considered. While clearly
intended to be used only for oil eld equipment, industry has
applied MR0175 in to many other areas including reneries, LNG
plants, pipelines and natural gas systems. The judicious use of
the document in these applications is constructive and can help
prevent SSC failures wherever H2S is present. Saltwater wells and
saltwater handling facilities are not covered by NACE MR0175/
ISO 15156. These are covered by NACE Standard RP0475,
“Selection of Metallic Materials to Be Used in All Phases of Water
Handling for Injection into Oil-Bearing Formations.”
When new restrictions are placed on materials in NACE MR0175/
ISO 15156 or when materials are deleted from this standard,
materials in use at that time are in compliance. This includes
materials listed in MR0175-2002, but not listed in NACE
MR0175/ISO 15156. However, if this equipment is moved to a
different location and exposed to different conditions, the materials
must be listed in the current revision. Alternatively, successful use
of materials outside the limitations of NACE MR0175/ISO 15156
may be perpetuated by qualication testing per the standard. The
user may replace materials in kind for existing wells or for new
wells within a given eld if the environmental conditions of the
eld have not changed.
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
651
Te c h n i c a l
New Sulfide Stress Cracking Standard
for Refineries
Don Bush, Principal Engineer - Materials, at Emerson Process
Management Fisher Valves, is a member and former chair of
a NACE task group that has written a document for renery
applications, NACE MR0103. The title is “Materials Resistant
to Sulde Stress Cracking in Corrosive Petroleum Rening
Environments.” The requirements of this standard are very similar
to the pre-2003 MR0175 for many materials. When applying this
standard, there are changes to certain key materials compared with
NACE MR0175-2002.
Responsibility
It has always been the responsibility of the end user to determine
the operating conditions and to specify when NACE MR0175
applies. This is now emphasized more strongly than ever in NACE
MR0175/ISO 15156. The manufacturer is responsible for meeting
the metallurgical requirements of NACE MR0175/ISO 15156. It
is the end user’s responsibility to ensure that a material will be
satisfactory in the intended environment. Some of the operating
conditions which must be considered include pressure, temperature,
corrosiveness, uid properties, etc. When bolting components
are selected, the pressure rating of anges could be affected. It
is always the responsibility of the equipment user to convey the
environmental conditions to the equipment supplier, particularly if
the equipment will be used in sour service.
The various sections of NACE MR0175/ISO 15156 cover the
commonly available forms of materials and alloy systems. The
requirements for heat treatment, hardness levels, conditions of
mechanical work and post-weld heat treatment are addressed for
each form of material. Fabrication techniques, bolting, platings and
coatings are also addressed.
Applicability of NACE MR0175/ISO 15156
Low concentrations of H2S (<0.05 psi (0,3 kPa) H2S partial
pressure) and low pressures (<65 psia or 450 kPa) are considered
outside the scope of NACE MR0175/ISO 15156. The low stress
levels at low pressures or the inhibitive effects of oil may give
satisfactory performance with standard commercial equipment.
Many users, however, have elected to take a conservative approach
and specify compliance to either NACE MR0175 or NACE
MR0175/ISO 15156 any time a measurable amount of H2S is
present. The decision to follow these specications must be
made by the user based on economic impact, the safety aspects
should a failure occur and past eld experience. Legislation can
impact the decision as well. Such jurisdictions include; the Texas
Railroad Commission and the U.S. Minerals Management Service
(offshore). The Alberta, Canada Energy Conservation Board
recommends use of the specications.
Basics of Sulfide Stress Cracking (SSC) and Stress
Corrosion Cracking (SCC)
SSC and SCC are cracking processes that develop in the presence
of water, corrosion and surface tensile stress. It is a progressive
type of failure that produces cracking at stress levels that are
well below the material’s tensile strength. The break or fracture
appears brittle, with no localized yielding, plastic deformation or
elongation. Rather than a single crack, a network of ne, feathery,
branched cracks will form (see Figure 1). Pitting is frequently
seen, and will serve as a stress concentrator to initiate cracking.
With SSC, hydrogen ions are a product of the corrosion process
(Figure 2). These ions pick up electrons from the base material
producing hydrogen atoms. At that point, two hydrogen atoms
may combine to form a hydrogen molecule. Most molecules
will eventually collect, form hydrogen bubbles and oat away
harmlessly. However, some percentage of the hydrogen atoms will
diffuse into the base metal and embrittle the crystalline structure.
When a certain critical concentration of hydrogen is reached and
combined with a tensile stress exceeding a threshold level, SSC
will occur. H2S does not actively participate in the SSC reaction;
however, suldes act to promote the entry of the hydrogen atoms
into the base material.
As little as 0.05 psi (0,3 kPa) H2S partial pressure in 65 psia
(450 kPa) hydrocarbon gas can cause SSC of carbon and low
alloy steels. Sulde stress cracking is most severe at ambient
temperature, particularly in the range of 20° to 120°F (-6° to
49°C). Below 20°F (-6°C) the diffusion rate of the hydrogen is
Figure 1. Photomicrograph Showing Stress Corrosion Cracking
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
652
Te c h n i c a l
so slow that the critical concentration is never reached. Above
120°F (49°C), the diffusion rate is so fast that the hydrogen
atoms pass through the material in such a rapid manner that the
critical concentration is not reached.
Chloride SCC is widely encountered and has been extensively
studied. Much is still unknown, however, about its mechanism.
One theory says that hydrogen, generated by the corrosion
process, diffuses into the base metal in the atomic form and
embrittles the lattice structure. A second, more widely accepted
theory proposes an electrochemical mechanism. Stainless steels
are covered with a protective, chromium oxide lm. The chloride
ions rupture the lm at weak spots, resulting in anodic (bare)
and cathodic (lm covered) sites. The galvanic cell produces
accelerated attack at the anodic sites, which when combined with
tensile stresses produces cracking. A minimum ion concentration
is required to produce SCC. As the concentration increases, the
environment becomes more severe, reducing the time to failure.
Temperature also is a factor in SCC. In general, the likelihood of
SCC increases with increasing temperature. A minimum threshold
temperature exists for most systems, below which SCC is rare.
Across industry, the generally accepted minimum temperature for
chloride SCC of the 300 SST’s is about 160°F (71°C). NACE
MR0175/ISO 15156 has set a very conservative limit of 140°F
(60°C) due to the synergistic effects of the chlorides, H2S and low
pH values. As the temperature increases above these values, the
time to failure will typically decrease.
Resistance to chloride SCC increases with higher alloy materials.
This is reected in the environmental limits set by NACE
MR0175/ISO 15156. Environmental limits progressively increase
from 400 Series SST and ferritic SST to 300 Series, highly alloy
austenitic SST, duplex SST, nickel and cobalt base alloys.
Carbon Steel
Carbon and low-alloy steels have acceptable resistance to SSC and
SCC however; their application is often limited by their low resistance
to general corrosion. The processing of carbon and low alloy steels
must be carefully controlled for good resistance to SSC and SCC. The
hardness must be less than 22 HRC. If welding or signicant cold
working is done, stress relief is required. Although the base metal
hardness of a carbon or alloy steel is less than 22 HRC, areas of the
heat affected zone (HAZ) will be harder. PWHT will eliminate these
excessively hard areas.
ASME SA216 Grades WCB and WCC and SAME SA105 are
the most commonly used body materials. It is Fisher’s policy to
stress relieve all welded carbon steels that are supplied to NACE
MR0175/ISO 15156.
All carbon steel castings sold to NACE MR0175/ISO 15156
requirements are produced using one of the following processes:
1. In particular product lines where a large percentage of
carbon steel assemblies are sold as NACE MR0175/ISO
15156 compliant, castings are ordered from the foundry with
a requirement that the castings be either normalized or stress
relieved following all weld repairs, major or minor. Any
weld repairs performed, either major or minor, are
subsequently stress relieved.
2. In product lines where only a small percentage of carbon steel
products are ordered NACE MR0175/ISO 15156 compliant,
stock castings are stress relieved whether they are weld repaired
by Emerson Process Management or not. This eliminates the
chance of a minor foundry weld repair going undetected and not
being stress relieved.
ASME SA352 grades LCB and LCC have the same composition
as WCB and WCC, respectively. They are heat treated differently
and impact tested at -50°F (-46°C) to ensure good toughness in low
temperature service. LCB and LCC are used in locations where
temperatures commonly drop below the -20°F (-29°C) permitted for
WCB and WCC. LCB and LCC castings are processed in the same
manner as WCB and WCC when required to meet NACE MR0175/
ISO 15156.
For carbon and low-alloy steels NACE MR0175/ISO 15156
imposes some changes in the requirements for the weld procedure
qualication report (PQR). All new PQR’s will meet these
requirements; however, it will take several years for Emerson
Process Management and our suppliers to complete this work. At
this time, we will require user approval to use HRC.
H
H
H
H
H
H
H
H
H
H H
H
H
H
+
H
+
M
+
S
-2
H
+
H
+
H
+
H
+
S
-2
H
H
H
2
M
+
S
-2
M
+
e
-
e
-
e
-
σ
σ
Figure 2. Schematic Showing the Generation of Hydrogen Producing SSC
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
653
Te c h n i c a l
Carbon and Low-Alloy Steel Welding
Hardness Requirements
• HV-10, HV-5 or Rockwell 15N.
• HRC testing is acceptable if the design stresses are less than
67% of the minimum specied yield strength and the PQR
includes PWHT.
• Other methods require user approval.
• 250 HV or 70.6 HR15N maximum.
• 22 HRC maximum if approved by user.
Low-Alloy Steel Welding Hardness Requirements
• All of the above apply with the additional requirement of stress
relieve at 1150°F (621°C) minimum after welding.
All new PQR’s at Emerson Process Management and our foundries
will require hardness testing with HV-10, HV-5 or Rockwell 15N
and HRC. The acceptable maximum hardness values will be 250
HV or 70.6 HR15N and 22 HRC. Hardness traverse locations are
specied in NACE MR0175/ISO 15156 part 2 as a function of
thickness and weld conguration. The number and locations of
production hardness tests are still outside the scope of the standard.
The maximum allowable nickel content for carbon and low-alloy
steels and their weld deposits is 1%.
Low alloy steels like WC6, WC9, and C5 are acceptable to NACE
MR0175/ISO 15156 to a maximum hardness of 22 HRC. These
castings must all be stress relieved to FMS 20B52.
The compositions of C12, C12a, F9 and F91 materials do not fall
within the denition of “low alloy steel” in NACE MR0175/ISO
15156, therefore, these materials are not acceptable.
A few customers have specied a maximum carbon equivalent
(CE) for carbon steel. The primary driver for this requirement
is to improve the SSC resistance in the as-welded condition.
Fisher’s practice of stress relieving all carbon steel negates this
need. Decreasing the CE reduces the hardenability of the steel and
presumably improves resistance to sulde stress cracking (SSC).
Because reducing the CE decreases the strength of the steel, there
is a limit to how far the CE can be reduced.
Cast Iron
Gray, austenitic and white cast irons cannot be used for any
pressure-retaining parts, due to low ductility. Ferritic ductile iron
to ASTM A395 is acceptable when permitted by ANSI, API or
other industry standards.
Stainless Steel
400 Series Stainless Steel
UNS 410 (410 SST), CA15 (cast 410), 420 (420 SST) and several
other martensitic grades must be double tempered to a maximum
hardness of 22 HRC. PWHT is also required. An environmental
limit now applies to the martensitic grades; 1.5 psi (10 kPa) H2S
partial pressure and pH greater than or equal to 3.5, 416 (416 SST)
is similar to 410 (410) with the exception of a sulfur addition to
produce free machining characteristics. Use of 416 and other free
machining steels is not permitted by NACE MR0175/ISO 15156.
CA6NM is a modied version of the cast 410 stainless steel.
NACE MR0175/ISO 15156 allows its use, but species the
exact heat treatment required. Generally, the carbon content
must be restricted to 0.03% maximum to meet the 23 HRC
maximum hardness. PWHT is required for CA6NM. The same
environmental limit applies; 1.5 psi (10 kPa) H2S partial pressure
and pH greater than or equal to 3.5.
300 Series Stainless Steel
Several changes have been made with the requirements of the
austenitic (300 Series) stainless steels. Individual alloys are no
longer listed. All alloys with the following elemental ranges
are acceptable: C 0.08% maximum, Cr 16% minimum, Ni 8%
minimum, P 0.045% maximum, S 0.04% maximum, Mn 2.0%
maximum, and Si 2.0% maximum. Other alloying elements are
permitted. The other requirements remain; solution heat treated
condition, 22 HRC maximum and free of cold work designed to
improve mechanical properties. The cast and wrought equivalents of
302, 304 (CF8), S30403 (CF3), 310 (CK20), 316 (CF8M), S31603
(CF3M), 317 (CG8M), S31703 (CG3M), 321, 347 (CF8C) and
N08020 (CN7M) are all acceptable per NACE MR0175/ISO 15156.
Environmental restrictions now apply to the 300 Series SST. The
limits are 15 psia (100 kPa) H2S partial pressure, a maximum
temperature of 140°F (60°C), and no elemental sulfur. If the
chloride content is less than 50 mg/L (50 ppm), the H2S partial
pressure must be less than 50 psia (350 kPa) but there is no
temperature limit.
There is less of a restriction on 300 Series SST in oil and gas
processing and injection facilities. If the chloride content in
aqueous solutions is low (typically less than 50 mg/L or 50 ppm
chloride) in operations after separation, there are no limits for
austenitic stainless steels, highly alloyed austenitic stainless steels,
duplex stainless steels, or nickel-based alloys.
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
654
Te c h n i c a l
Post-weld heat treatment of the 300 Series SST is not required.
Although the corrosion resistance may be affected by poorly
controlled welding, this can be minimized by using the low carbon
ller material grades, low heat input levels and low interpass
temperatures. We impose all these controls as standard practice.
NACE MR0175/ISO 15156 now requires the use of “L” grade
consumables with 0.03% carbon maximum.
S20910
S20910 (Nitronic® 50) is acceptable in both the annealed and high
strength conditions with environmental restrictions; H2S partial
pressure limit of 15 psia (100 kPa), a maximum temperature
of 150°F (66°C), and no elemental sulfur. This would apply
to components such as bolting, plugs, cages, seat rings and
other internal parts. Strain hardened (cold-worked) S20910 is
acceptable for shafts, stems, and pins without any environmental
restrictions. Because of the environmental restrictions and poor
availability on the high strength condition, use of S20910 will
eventually be discontinued except for shafts, stems and pins where
unrestricted application is acceptable for these components.
CK3MCuN
The cast equivalent of S31254 (Avesta 254SMO®), CK3MCuN
(UNS J93254), is included in this category. The same elemental
limits apply. It is acceptable in the cast, solution heat-treated
condition at a hardness level of 100 HRB maximum in the absence
of elemental sulfur.
S17400
The use of S17400 (17-4PH) is now prohibited for pressureretaining components including bolting, shafts and stems. Prior to
2003, S17400 was listed as an acceptable material in the general
section (Section 3) of NACE MR0175. Starting with the 2003
revision, however, it is no longer listed in the general section. Its
use is restricted to internal, non-pressure containing components
in valves, pressure regulators and level controllers. This includes
cages and other trim parts. 17-4 bolting will no longer be supplied
in any NACE MR0175/ISO 15156 construction. The 17-4 and
15-5 must be heat-treated to the H1150 DBL condition or the
H1150M condition. The maximum hardness of 33 HRC is the
same for both conditions.
CB7Cu-1 and CB7Cu-2 (cast 17-4PH and 15-5 respectively) in
the H1150 DBL condition are also acceptable for internal valve
and regulator components. The maximum hardness is 30 HRC or
310 HB for both alloys.
Duplex Stainless Steel
Wrought and cast duplex SST alloys with 35-65% ferrite are
acceptable based on the composition of the alloy, but there are
environmental restrictions. There is no differentiation between cast
and wrought, therefore, cast CD3MN is now acceptable. There
are two categories of duplex SST. The “standard” alloys with a
30≤PREN≤40 and ≥1.5% Mo, and the “super” duplex alloys with
PREN>40. The PREN is calculated from the composition of the
material. The chromium, molybdenum, tungsten and nitrogen
contents are used in the calculation. NACE MR0175/ISO 15156
uses this number for several classes of materials.
PREN = Cr% + 3.3(Mo% + 0.5W%) + 16N%
The “standard” duplex SST grades have environmental limits of
450°F (232°C) maximum and H2S partial pressure of 1.5 psia (10 kPa)
maximum. The acceptable alloys include S31803, CD3MN, S32550
and CD7MCuN (Ferralium® 255). The alloys must be in the solution
heat-treated and quenched condition. There are no hardness restrictions
in NACE MR0175/ISO 15156, however, 28 HRC remains as the limit
in the renery document MR0103.
The “super” duplex SST with PREN>40 have environmental limits of
450°F (232°C) maximum and H2S partial pressure of 3 psia (20 kPa)
maximum. The acceptable “super” duplex SST’s include S32760 and
CD3MWCuN (Zeron® 100).
The cast duplex SST Z 6CNDU20.08M to the French National
Standard NF A 320-55 is no longer acceptable for NACE MR0175/
ISO 15156 applications. The composition fails to meet the
requirements set for either the duplex SST or the austenitic SST.
Highly Alloyed Austenitic Stainless Steels
There are two categories of highly alloyed austenitic SST’s that are
acceptable in the solution heat-treated condition. There are different
compositional and environmental requirements for the two categories.
The rst category includes alloys S31254 (Avesta 254SMO®) and
N08904 (904L); Ni% + 2Mo%>30 and Mo=2% minimum.
Alloy S31254 and N08904 Environmetal Limits
MAXIMUM
TEMPERATURE
MAXIMUM H2S
PARTIAL
PRESSURE
MAXIMUM
CHLORIDES
ELEMENTAL
SULFUR
140°F (60°C) 1.5 psia (10 kPa) No restriction No
140°F (60°C) 50 psia (345 kPa) 50 mg/L Chloride No
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
655
Te c h n i c a l
Alloy N07718 and N09925 Environmental Limits
MAXIMUM
TEMPERATURE
MAXIMUM H
L
2
S
PARTIAL PRESSURE
ELEMENTAL SULFUR
450°F (232°C) 30 psia (0,2 MPa) No
400°F (204°C) 200 psia (1,4 MPa) No
390°F (199°C) 330 psia (2,3 MPa) No
375°F (191°C) 360 psia (2,5 MPa) No
300°F (149°C) 400 psia (2,8 MPa) No
275°F (135°C) No limit Yes
Cast N07718 Environmental Limits
MAXIMUM
TEMPERATURE
MAXIMUM H
2
2
S
PARTIAL PRESSURE
ELEMENTAL
SULFUR
450°F (232°C) 30 psia (0,2 MPa) No
400°F (204°C) 200 psia (1,4 MPa) No
300°F (149°C) 400 psia (2,8 MPa) No
275°F (135°C) No limit Yes
Monel® K500 and Inconel® X750
N05500 and N07750 are now prohibited for use in pressureretaining components including bolting, shafts and stems. They
can still be used for internal parts such as cages, other trim
parts and torque tubes. There are no environmental restrictions,
however, for either alloy. They must be in the solution heat-treated
condition with a maximum hardness of 35 HRC. N07750 is still
acceptable for springs to 50 HRC maximum.
Cobalt-Base Alloys
Alloy 6 castings and hardfacing are still acceptable. There are
no environmental limits with respect to partial pressures of H2S
or elemental sulfur. All other cobalt-chromium-tungsten, nickelchromium-boron (Colmonoy) and tungsten-carbide castings are
also acceptable without restrictions.
The second category of highly alloyed austenitic stainless steels
are those having a PREN >40. This includes S31654 (Avesta
654SMO®), N08926 (Inco 25-6Mo), N08367 (AL-6XN), S31266
(UR B66) and S34565. The environmental restrictions for these
alloys are as follows:
Alloy S31654, N08926, N08367, S31266, and S34565
Environmental Limits
MAXIMUM
TEMPERATURE
MAXIMUM H
2
2
S
PARTIAL PRESSURE
MAXIMUM
CHLORIDES
ELEMENTAL
SULFUR
250°F (121°C) 100 psia (700 kPa) 5,000 mg/L chloride No
300°F (149°C) 45 psia (310 kPa) 5,000 mg/L chloride No
340°F (171°C) 15 psia (100 kPa) 5,000 mg/L chloride No
Nonferrous Alloys
Nickel-Base Alloys
Nickel base alloys have very good resistance to cracking in sour,
chloride containing environments. There are 2 different categories
of nickel base alloys in NACE MR0175/ISO 15156:
• Solid-solution nickel-based alloys
• Precipitation hardenable alloys
The solid solution alloys are the Hastelloy® C, Inconel® 625 and
Incoloy® 825 type alloys. Both the wrought and cast alloys are
acceptable in the solution heat-treated condition with no hardness
limits or environmental restrictions. The chemical composition of
these alloys is as follows:
• 19.0% Cr minimum, 29.5% Ni minimum, and 2.5% Mo
minimum. Includes N06625, CW6MC, N08825, CU5MCuC.
• 14.5% Cr minimum, 52% Ni minimum, and 12% Mo
minimum. Includes N10276, N06022, CW2M.
N08020 and CN7M (alloy 20 Cb3) are not included in this
category. They must follow the restrictions placed on the
austenitic SST’s like 304, 316 and 317.
Although originally excluded from NACE MR0175/ISO 15156,
N04400 (Monel® 400) in the wrought and cast forms are now
included in this category.
The precipitation hardenable alloys are Incoloy® 925, Inconel® 718
and X750 type alloys. They are listed in the specication as individual
alloys. Each has specic hardness and environmental restrictions.
N07718 is acceptable in the solution heat-treated and precipitation
hardened condition to 40 HRC maximum. N09925 is acceptable
in the cold-worked condition to 35 HRC maximum, solutionannealed and aged to 38 HRC maximum and cold-worked and
aged to 40 HRC maximum.
The restrictions are as follows:
Cast N07718 is acceptable in the solution heat-treated and
precipitation hardened condition to 35 HRC maximum. The
restrictions are as follows:
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
656
Te c h n i c a l
All cobalt based, nickel based and tungsten-carbide weld overlays
are acceptable without environmental restrictions. This includes
CoCr-A, NiCr-A (Colmonoy® 4), NiCr-C (Colmonoy® 6) and
Haynes Ultimet® hardfacing.
Wrought UNS R31233 (Haynes Ultimet®) is acceptable in the solution
heat-treated condition to 22 HRC maximum, however, all production
barstock exceeds this hardness limit. Therefore, Ultimet® barstock
cannot be used for NACE MR0175/ISO 15156 applications. Cast
Ultimet is not listed in NACE MR0175/ISO 15156.
R30003 (Elgiloy®) springs are acceptable to 60 HRC in the cold
worked and aged condition. There are no environmental restrictions.
Aluminum and Copper Alloys
Per NACE MR0175/ISO 15156, environmental limits have not
been established for aluminum base and copper alloys. This
means that they could be used in sour applications per the
requirements of NACE MR0175/ISO 15156, however, they should
not be used because severe corrosion attack will likely occur.
They are seldom used in direct contact with H2S.
Titanium
Environmental limits have not been established for the wrought
titanium grades. Fisher® has no experience in using titanium in
sour applications. The only common industrial alloy is wrought
R50400 (grade 2). Cast titanium is not included in NACE
MR0175/ISO 15156.
Zirconium
Zirconium is not listed in NACE MR0175/ISO 15156.
Springs
Springs in compliance with NACE represent a difcult problem.
To function properly, springs must have very high strength
(hardness) levels. Normal steel and stainless steel springs would
be very susceptible to SSC and fail to meet NACE MR0175/ISO
15156. In general, relatively soft, low strength materials must
be used. Of course, these materials produce poor springs. The
two exceptions allowed are the cobalt based alloys, such as
R30003 (Elgiloy®), which may be cold worked and hardened to
a maximum hardness of 60 HRC and alloy N07750 (alloy X750)
which is permitted to 50 HRC. There are no environmental
restrictions for these alloys.
Coatings
Coatings, platings and overlays may be used provided the base
metal is in a condition which is acceptable per NACE MR0175/ISO
15156. The coatings may not be used to protect a base material
which is susceptible to SSC. Coatings commonly used in sour
service are chromium plating, electroless nickel (ENC) and
nitriding. Overlays and castings commonly used include CoCrA (Stellite® or alloy 6), R30006 (alloy 6B), NiCr-A and NiCr-C
(Colmonoy® 4 and 6) nickel-chromium-boron alloys. Tungsten
carbide alloys are acceptable in the cast, cemented or thermally
sprayed conditions. Ceramic coatings such as plasma sprayed
chromium oxide are also acceptable. As is true with all materials in
NACE MR0175/ISO 15156, the general corrosion resistance in the
intended application must always be considered.
NACE MR0175/ISO 15156 permits the uses of weld overlay
cladding to protect an unacceptable base material from cracking.
Fisher does not recommend this practice, however, as hydrogen
could diffuse through the cladding and produce cracking of a
susceptible basemetal such as carbon or low alloy steel.
Stress Relieving
Many people have the misunderstanding that stress relieving
following machining is required by NACE MR0175/ISO 15156.
Provided good machining practices are followed using sharp
tools and proper lubrication, the amount of cold work produced is
negligible. SSC and SCC resistance will not be affected. NACE
MR0175/ISO 15156 actually permits the cold rolling of threads,
provided the component will meet the heat treat conditions and
hardness requirements specied for the given parent material. Cold
deformation processes such as burnishing are also acceptable.
Bolting
Bolting materials must meet the requirements of NACE MR0175/
ISO 15156 when directly exposed to the process environment
(“exposed” applications). Standard ASTM A193 and ASME
SA193 grade B7 bolts or ASTM A194 and ASME SA194 grade
2H nuts can and should be used provided they are outside of
the process environment (“non-exposed” applications). If the
bolting will be deprived atmospheric contact by burial, insulation
or ange protectors and the customer species that the bolting
will be “exposed”, then grades of bolting such as B7 and 2H
are unacceptable. The most commonly used fasteners listed for
“exposed” applications are grade B7M bolts (99 HRB maximum)
and grade 2HM nuts (22 HRC maximum). If 300 Series SST
fasteners are needed, the bolting grades B8A Class 1A and B8MA
Class 1A are acceptable. The corresponding nut grades are 8A
and 8MA.
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
657
Te c h n i c a l
It must be remembered, however, that the use of lower strength
bolting materials such as B7M may require pressure vessel
derating. The special S17400 double H1150 bolting previously
offered on E body valves to maintain the full B7 rating is no longer
acceptable to NACE MR0175/ISO 15156. Prior to the 2003,
S17400 was listed as an acceptable material in the general section
(Section 3) of NACE MR0175. Following the 2003 revision, it is
no longer listed in the general section. Its use is now restricted to
internal, non-pressure containing components in valves, pressure
regulators and level controllers. The use of S17400 for bolting is
specically prohibited. N07718 (alloy 718) bolting with 2HM nuts
is one alternative.
Two different types of packing box studs and nuts are commonly
used by Fisher®. The stainless steel type is B8M S31600 class 2
(strain hardened) and 316 nuts per FMS 20B86. The steel type is B7
studs with 2H nuts. If the customer species that the packing box
studs and nuts are “exposed” then grade B7M studs and grade 2HM
nuts or B8MA Class 1A studs and 8MA nuts are commonly used.
Bolting Coatings
NFC (Non-Corroding Finish) and ENC (Electroless Nickel
Coating) coatings are acceptable on pressure-retaining and nonpressure-retaining fasteners. For some reason, there is often
confusion regarding the acceptability of zinc plated fasteners per
NACE MR0175/ISO 15156. NACE MR0175/ISO 15156 does
not preclude the use of any coating, provided it is not used in an
attempt to prevent SSC or SCC of an otherwise unacceptable base
material. However, zinc plating of pressure-retaining bolting is not
recommended due to liquid metal induced embrittlement concerns.
Composition Materials
NACE MR0175/ISO 15156 does not address elastomer and
polymer materials although ISO/TC 67, Work Group 7 is now
working on a Part 4 to address these materials. The importance
of these materials in critical sealing functions, however, cannot be
overlooked. User experience has been successful with elastomers
such as Nitrile (NBR), Neoprene and the Fluoroelastomers (FKM)
and Peruoroelastomers (FFKM). In general, uoropolymers such
as Polytetrauoroethylene (PTFE), TCM Plus, TCM Ultra and
TCM III can be applied without reservation within their normal
temperature range.
Elastomer use is as follows:
1. If possible, use HNBR for sour natural gas, oil, or water at
temperatures below 250°F (121°C). It covers the widest
range of sour applications at a lower cost than PTFE or
Fluoroelastomer (FKM). Unfortunately, the material is
relatively new, and only a handful of parts are currently set
up. Check availability before specifying.
2. Use PTFE for sour natural gas, oil, or water applications
at temperatures between 250°F (121°C) and 400°F (204°C).
3. Fluoroelastomer (FKM) can be used for sour natural gas,
oil, or water applications with less than 10% H2S and
temperatures below 250°F (121°C).
4. Conventional Nitrile (NBR) can be used for sour natural
gas, oil, or water applications with less than 1% H2S and
temperatures below 150°F (66°C).
5. CR can be used for sour natural gas or water applications
involving temperatures below 150°F (66°C). Its resistance to
oil is not as good.
6. IIR and Ethylenepropylene (EPDM) (or EPR) can be used for
H2S applications that don’t involve hydrocarbons (H2S gas, sour
water, etc.).
Tubulars
A separate section has been established for downhole tubulars and
couplings. This section contains provisions for using materials in
the cold-drawn condition to higher hardness levels (cold-worked
to 35 HRC maximum). In some cases, the environmental limits
are also different. This has no affect on Fisher as we do not make
products for these applications. Nickel-based components used for
downhole casing, tubing, and the related equipment (hangers and
downhole component bodies; components that are internal to the
downhole component bodies) are subject to the requirements.
Expanded Limits and Materials
With documented laboratory testing and/or eld experience, it is
possible to expand the environmental limits of materials in NACE
MR0175/ISO 15156 or use materials not listed in NACE MR0175/
ISO 15156. This includes increasing the H2S partial pressure
limit or temperature limitations. Supporting documentation must
be submitted to NACE International Headquarters, which will
make the data available to the public. NACE International will
neither review nor approve this documentation. It is the user’s
responsibility to evaluate and determine the applicability of the
documented data for the intended application.
It is the user’s responsibility to ensure that the testing cited is
relevant for the intended applications. Choice of appropriate
temperatures and environments for evaluating susceptibility to
both SCC and SSC is required. NACE Standard TM0177 and EFC
Publication #1739 provide guidelines for laboratory testing.
Sulfide Stress Cracking
--NACE MR0175-2002, MR0175/ISO 15156
658
Te c h n i c a l
Field-based documentation for expanded alloy use requires
exposure of a component for sufcient time to demonstrate its
resistance to SCC/SSC. Sufcient information on factors that affect
SCC/SSC (e.g., stress levels, uid and gas composition, operating
conditions, galvanic coupling, etc.) must be documented.
Codes and Standards
Applicable ASTM, ANSI, ASME and API standards are used
along with NACE MR0175/ISO 15156 as they would normally
be used for other applications. The NACE MR0175/ISO 15156
requires that all weld procedures be qualied to these same
standards. Welders must be familiar with the procedures and
capable of making welds which comply.
Certification
Fisher® Certication Form 7508 is worded as follows for NACE
MR0175-2002 and MR0175/ISO 15156:
“NACE MR0175/ISO 15156 OR NACE MR0175-2002: This unit
meets the metallurgical requirements of NACE MR0175 or ISO
15156 (revision and materials of construction as specied by the
customer). Environmental restrictions may apply to wetted parts
and/or bolting.”
Loading...