Fisher IM Supplement: CSA Hazardous Area Approvals - FIELDVUE DVC6200 Series Digital Valve Controllers Manuals & Guides

Instruction Manual Supplement

D104203X012

DVC6200 Digital Valve Controllers

July 2017

CSA Hazardous Area Approvals

™

Fisher

FIELDVUE™ DVC6200 Series

Digital Valve Controllers

Hazardous Area Approvals and Special Instructions
for “Safe Use” and Installations in Hazardous Locations

Certain nameplates may carry more than one approval, and each approval may have unique installation/wiring
requirements and/or conditions of “safe use”. These special instructions for “safe use” are in addition to, and may
override, the standard installation procedures. Special instructions are listed by approval type.

Note

This information supplements the nameplate markings affixed to the product and the DVC6200 Series quick start guide
(D103556X012

Always refer to the nameplate itself to identify the appropriate certification.

), available from your Emerson sales office or Local Business Partner, or at Fisher.com.

SIS

WARNING

Failure to follow these conditions of “safe use” could result in personal injury or property damage from fire or explosion
and area re‐classification.

Ordinary Locations Approval

Complies with general electrical safety CAN/CSAC22.2 No. 6101012004

SELV, conduit connected, Enclosure Type 4X, IP66, Installation Category I, Pollution Degree 4

DVC6200 Series (HART HW1, F
Rated Input 9-30 VDC, 4-20 mA

-52_C to + 80_C Ambient
DVC6205 (HART HW1, F
Rated Input 9-30 VDC, 4-20 mA Rated Input 10 VDC max, 3.5 mA max

Outputs 0-9.6 VDC, 0-3.5 mA -52 to 125_C Ambient
-52_C to + 80_C Ambient

OUNDATION Fieldbus, PROFIBUS)

OUNDATION fieldbus, PROFIBUS) DVC6215 Remote Mount

www.Fisher.com

DVC6200 Digital Valve Controllers

July 2017

Instruction Manual Supplement

Explosion-proof and Dust Ignition-proof

DVC6200 and DVC6205 Series (HART HW1 & HW2, SIS, FOUNDATION Fieldbus, PROFIBUS)

Class I, Division 1, Groups B,C,D ; Class I, Division 2, Groups A,B,C,D
Class II, Division 1, Groups E,F,G ; Class II, Division 2, Groups F,G
Class III, Division 1
Ex d IIC
Ex nC IIC
Type 4X, IP66
Single Seal Device (HART HW2 and SIS pending)

Rated input 30 Vmax, 20 mA

- 52_C < Ambient < + 80_C
Max inlet pressure 10 bar (145 psig) (air or natural gas)
Temperature Code: T6 (Tamb ≤ 75_C), T5 (Tamb ≤ 80_C)

DVC6215 Remote Mount

Class I, Division 1, Groups A,B,C,D ; Class I, Division 2, Groups A,B,C,D
Class II, Division 1, Groups E,F,G ; Class II, Division 2, Groups F,G
Class III, Division 1
Ex d IIC
Ex nA IIC
Type 4X, IP66

Rated input 30 Vmax, 20 mA

- 52_C < Ambient < + 125_C
Temperature Code: T6 (Tamb ≤ 75_ C), T5 (Tamb ≤ 90_C), T4 (Tamb ≤ 125_C)

D104203X012

Intrinsically Safe

Class I, Division 1, Groups A,B,C,D
Class II, Division 1, Groups E,F,G
Class III, Division 1
Ex ia IIC
Type 4X, IP66
Single Seal Device (HART HW2 and SIS pending)

Rated input 30 V DC max, 20 mA

- 52 _C < Ambient < + 80_C (-52_C to 125_C for DVC6215)
Max inlet pressure 10 bar (145 psig) (air or natural gas)

Intrinsically safe when connected per installation drawing GE42818, as shown in the following figures

DVC6200 HW2 and DVC6200 SIS figure 1 and 6...........................

DVC6205, DVC6205 SIS, and DVC6215 Remote Mount figure 2 and 6........

DVC6200f and DVC6200p figure 3 and 6.................................

DVC6205f, DVC6205p, and DVC6215 Remote Mount figure 4 and 6.........

DVC6200 HW1 figure 5 and 6...........................................

2

Instruction Manual Supplement

D104203X012

Figure 1. CSA Loop Schematics—FIELDVUE DVC6200 HW2 and DVC6200 SIS

DVC6200 Digital Valve Controllers

July 2017

CLASS I, ZONE 0, GROUP IIC
CLASS I, DIV 1, GROUPS ABCD
CLASS II, DIV 1, GROUPS EFG
CLASS III

HW2 - WITH OR WITHOUT I/O PACKAGE
DVC6200, DVC6200S

LOOP TERMINALS

Vmax = 30 VDC
Imax = 130 mA
Ci = 15 nF
Li = 0.55 mH
Pi = 1.0 W

OUTPUT TERMINALS

Vmax = 28 VDC
Imax = 100 mA
Ci = 15 nF
Li = 0.5 mH
Pi = 1.0 W

HAZARDOUS LOCATION

1 NOTE 7

NON‐HAZARDOUS LOCATION

CSA APPROVED BARRIER

NOTE 1, 3, 4, 5, 6 1

CSA APPROVED BARRIER

NOTE 1, 3, 4, 5, 6 1

POWER MAY BE APPLIED TO
EITHER THE LOOP TERMINALS OR
OUTPUT TERMINALS OR TO BOTH
SETS OF TERMINALS AT THE SAME
TIME

UNITS WITHOUT THE I/O PACKAGE
WILL NOT HAVE “OUTPUT
TERMINALS” AVAILABLE FOR
CONNECTION

T CODE T (amb) T (amb)

T5 ≤ 80_C ≤ 80_C

T6 ≤ 61_C ≤ 74_C

GE42818 Sheet 11, Rev. C

1 SEE NOTES IN FIGURE 6

WITH

I/O PACKAGE

WITHOUT

I/O PACKAGE

3